The stepped shaft shown in Figure 3(a) must transmit 40 kW at a speed of 720 rpm. If an allowable stress of 36 MPa is not to be exceeded, i. Determine the stress concentration factor K Ans : 1.214 1.8 ii. Determine the minimum radius r of the fillet using the graph in Figure 1.7 Ans : 10.8 mm (11.25 mm>r> 10.13mm) 8-11 -물-125 1.6 D. 1.5 -1.666 (1.4 -2

The stepped shaft shown in Figure 3(a) must transmit 40 kW at a speed of 720 rpm. If an allowable stress of 36 MPa is not to be exceeded, i. Determine the stress concentration factor K Ans : 1.214 1.8 ii. Determine the minimum radius r of the fillet using the graph in Figure 1.7 Ans : 10.8 mm (11.25 mm>r> 10.13mm) 8-11 -물-125 1.6 D. 1.5 -1.666 (1.4 -2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A hollow circular shaft with OD 1.5 and ID 1.25 and made of steel with an allowable shear stress of 15 ksi is rated for 5000 in-lbs of torque. A narrow slit is cut lengthwise along the shaft as shown in the figure on the right. Determine the rated capacity of the shaft after it has been modified. Choose the answer that is closest from the list below. 0 0 0 0 3,600 in lbs 360 in-lbs 1,800 in-lbs 2,500 in-lbs
A hollow steel shaft transmits 600 kW at 500 rpm. The maximum shear stress is 62.4 MPa. Find the outside and inside diameter of the shaft, if the outer diameter is twice of inside diameter, assuming that the maximum torque is 20% greater than the mean torque The answer is 100mm and 50 mm. can you help me this calculation and i give the answer already. and write with pen. tqvm
The solid steel shaft is supported by the frictionless customer on D and E. This system The mile provided 5 kW of power in w dev / second and was connected to a motor at C. wwww ww www ww ww www wwwm www w A and B If gears get primary 2 kW and 3 kW, determine the minimum shaft diameter. w rotation speed and The safety shear stress is known and is included in the table below. pictures. wwww ww wwwwwwwww www wwwwww wwwwwwww wwwwwwwww w(cycle/second) = 100 tem(Mpa) = 40 3 kW 5 kW 2 kW A D B E C _
3:35 PM Wed Dec 15 7 51% A power transmission shaft is to carry a steady 30 horsepower while rotating at 1000 rpm. Specify a suitable diameter for the solid circular shaft if it is to be made from AISI 1020 cold-drawn steel. Use Appendix A-2 for preferred size. 61
What is the minimum diameter in mm of a solid steel shaft that will not twist through more than 3° in 6 meter length, when subjected to a torque of 14 kN m. Use G of 83 Gpa. 1180 118 0.0118 O 0.118
A solid 2.0 in. diameter shaft is used to synchronize multiple mechanisms in a manufacturing plant. The torque delivered by the shaft is 3300 Ib-in. What horsepower must be delivered to the shaft to maintain a shaft speed of 590 rpm? What is the maximum shear stress developed in the shaft? Answer: P = hp psi Save for Later Attempts: 0 of 1 used Submit Answer
A step shaft (shown to the right) is sub- jected to a torque, T (not shown). The shaft is made of copper. Use a factor of safety of 2.0 (and t y) and take into account the stress concentration due to the change in diameter of the shaft. 0.75 1/16" radius 0.35" Determine the maximum allowable torque T that may be applied. 9.13 lb-in.
A solid 1.9 in. diameter shaft is used to synchronize multiple mechanisms in a manufacturing plant. The torque delivered by the shaft is 3500 lb-in. What horsepower must be delivered to the shaft to maintain a shaft speed of 520 rpm? What is the maximum shear stress developed in the shaft? Part 1 Convert the given shaft speed to units of rad/s. Answer: W= i rad/s
A solid shaft consisting of steel and aluminum segments carries the torques T and 2T. Find the largest allowable value of T if the working shear stress is 14,000 psi for steel and 7,500 psi for aluminum, and the angle of rotation at the free end must not exceed 8 degrees. Use G = 12 x 10^6 psi for steel and G =4 x 10^6 psi for aluminum. Express your final answer in Ib.ft to the nearest whole number. Note: Do not include the unit in your answer. 27 2 in. 1.5 in. 3 ft B 2 ft |C 800mm 500mm
The drive shaft for a truck (outer diameter 60 mm and inner diameter 40 mm) is running at 42 Hz. If the shaft transmits 133 kW, what is the maximum shear stress in the shaft in MPa? Round up final answer to whole number
Micro Bh Micros Bb Micros - с * Question Completion Status: Question 2 2.0 d=1.50 in. dia. 1.9 1.8 Class r = 0.08 in. The figure below show a stepped shaft in torsion. Compute the maximum shear stress at the step when it rotates at 100 rad/s and transmits 5000 lb-in/s. Use CamScanner app or Notes app of iPhone to scan all hand-written pages into one PDF file. Attach the PDF file here to answer in this question. Class ( bbhosted.cuny.edu/webapps/assessment/take/take.jsp?course_assessment_id=_2374 Class D = 2.00 in. dia. r= Fillet radius Class G Cuent Projec suntur Et WA AS hp
A solid 1.5 in. diameter shaft is used to synchronize multiple mechanisms in a manufacturing plant. The torque delivered by the shaft is 3500 lb-in. What horsepower must be delivered to the shaft to maintain a shaft speed of 670 rpm? What is the maximum shear stress developed in the shaft? Convert the given shaft speed to units of rad/s. Answer: W = i rad/s