The steel rod is stress-free before the axial loads P₁ =169 kN and P2 = 88 kN are applied to the rod. Assuming that the walls are rigid, calculate the axial force in each segment after the loads are applied. Use E=200 GPa. A = 2000 mm² A = 900 mm² A = 1200 mm² P P B C D +25 -250 mm- m+++ 500 mm -350 mm A ANSWER: PCD = KN, PAB = KN, PBC = KN

The steel rod is stress-free before the axial loads P₁ =169 kN and P2 = 88 kN are applied to the rod. Assuming that the walls are rigid, calculate the axial force in each segment after the loads are applied. Use E=200 GPa. A = 2000 mm² A = 900 mm² A = 1200 mm² P P B C D +25 -250 mm- m+++ 500 mm -350 mm A ANSWER: PCD = KN, PAB = KN, PBC = KN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2 decimal places
please recheck your final answer.
PROBLEM 3 340 mm The plates are connected by 9-20 mm bolts. Force F = 5Ở KN are applied at both plates in opposite directions as shown in Figure 3. Compute the following: A. Axial stress of each plate. B. Shear stress of each bolt. Assume that each bolt resists the applied force equally. %3D +F 150 mm 中 F 50 mm 340 mm Figure 3: Bolted Plates
Fig shows a 700 mm length of aluminum alloy bar is suspended from the ceiling such away to provide a clearance of 0.3 mm between it and a 250 mm length of steel bar as shown in figure. Aal = 1250 mm² Eat =70 GN/m²; A = 2500 mm², E, = 210 GN/m². Find the stress in the aluminum and in the steel due to a 300 kN load applied 500 mm from the ceiling. 0.3 mm- 250 mm 500 mm 200 mm 300kN o Steel Aluminum M N
Please show all steps so your process is easy to follow
A rectangular plate is subjected to uniform biaxial stress with x = 90 MPa (tension), oy = -20 MPa (compression), and ₂ = 0. The plate has original dimensions 400 X 800 X 200 mm (x X y X z) and is made of steel with E = 200 GPa and v = 0.3. What are the strains Ex, Ey, and Ez?
The post shown, whose cross-sectional area is 100 x 150 mm2, rests at the middle of a circular solid steel plate. The steel plate is placed above a hollow cylinder. Both the steel plate and the cylinder have diameter of 300 mm and a thickness of 20 mm. Solve for the following: a. punching shear stress in the steel plate b. punching shear stress in the hollow cylinder c. bearing stress in the steel plate due to the post d. bearing stress in the cylinder due to the steel plate
!! Show Complete & Detailed Solution w/ FBD !!The bronze bar 3 m long with a cross-sectional area of 350 mm^2 is placed between two rigid walls. At a temperature of –25C, there is a gap  = 2.5 mm, as shown in the figure. Find the temperature at which the compressive stress in the bar will be 30 MPa. Use α = 18.0 x 10–6 /C and E = 80 GPa.
4. A rigid block of having a weight M is suspended by symmetrically placed rods. Each copper rod has an area of 1200 sq.mm: E= 125,000 MPa and the allowable stress is 90 MPa. The steel rod has an area of 1500 sq.mm; E 220GPa; and the allowable stress is 120 Mpa. Determine the largest weight M which can be supported by the rods. 8c=8s Copper 160 mm Pc Ps Steel 240 mm TIT Pc ..initial level Tinal level Copper 160 mm
A flat steel bar, 30 mm wide by 2 mm thick and 1.6 m long, is bent by couples applied at the ends so that the midpoint deflection is 23 mm. Compute the maximum stress in the bar. Use E =210GPA. Answer must be in MPa.
A circle of diameter d = 225 mm is inscribed on an unstressed aluminum plate of thickness t = 18 mm. Forces acting in the plane of the plate later cause normal stresses o₂ = 84 MPa and o₂ = 140 MPa For E= 70 GPa and v=- (v = poisson's ratio), determine the change in y D Listah 380 mm A C 0₁ 380 mm B (i) The length of diameter AB, (ii) The length of diameter CD, (iii) The thickness of the plate, x
Determine the compressive force (in N) in the bars shown after a temperature rise of 165°F if d = 0.011 in. Round off the final answer to five decimal places. d ... L M Use the following data: Bronze Aluminum A = 2.33 sq. in E = 14988461 psi A = 2.6 sq. in E = 10519262 psi L = 17.3 in L = 12.6 in a = 11.71 x 106/ °F. a = 12.73 x 106/°F