The spherical grit particles, having a radius of 0.01mm and specific gravity of 3.0, need to be separated in a settling chamber. It is given that g=9.81m/s² the density of the liquid in the settling chamber = 1000kg / m³ the kinematic viscosity of the liquid in the settling chamber = 10 m²/s Assuming laminar conditions, the settling velocity (in mm/s, up to one decimal place) is_

The spherical grit particles, having a radius of 0.01mm and specific gravity of 3.0, need to be separated in a settling chamber. It is given that g=9.81m/s² the density of the liquid in the settling chamber = 1000kg / m³ the kinematic viscosity of the liquid in the settling chamber = 10 m²/s Assuming laminar conditions, the settling velocity (in mm/s, up to one decimal place) is_

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter7: Permeability

Section: Chapter Questions

Problem 7.17P

See similar textbooks

Similar questions

The spherical grit particles, having a radius of 0.01 mm and specific gravity of 3.0, need to be separated in a settling chamber. It is given that g=9.81m/s² • the density of the liquid in the settling ● chamber = 1000kg / m² · • the kinematic viscosity of the liquid in the settling chamber = 10-6 m² / s Assuming laminar conditions, the settling velocity (in mm/s, up to one decimal place) is____
Q-The spherical grit particles, having a radius of 0.01 mm and specific gravity of 3.0, need to be separated in a settling chamber. It is given that g=9.81m/s² the density of the liquid in the settling chamber =1000kg / m³ the kinematic viscosity of the liquid in the settling chamber = 10 m² (s Assuming laminar conditions, Find the settling velocity.
3. The capillary pressure data for a water-oil system are given below: Sw Pc 0.25 35 0.30 16 0.40 8.5 0.50 1.0 The core sample used in generalizing the capillary pressure data was taken from a layer that is characterized by an absolute permeability of 300 md and a porosity of 17%. Generate the capillary pressure data for a different layer that is characterized by a porosity and permeability of 15%, 200 md, respectively. The interfacial tension is measured at 35 dynes/cm.
In a water treatment, the temperature of water is 20°C. The diameter of the solid particles present in water is 0.05 mm and have specific gravity of 1.2. Determine the settling velocity of the partiles if the kinematic viscosity of water is 1.01 cSt.
Estimate the terminal settling velocity in water at a temperature of 15°C of spherical silicon particles with specific gravity 2.4 and average diameter of 0.05mm. Assume ρ=999 kg/m3 and µ= 0.00113 Ns/m2
5. A packed bed of solid particles of density 2500 kg/m3 occupies a depth of 1 m in a vessel of cross-sectional area 0.04 m2. The mass of solids in the bed is 50 kg and the surface- volume mean diameter of the particles is 1mm. A liquid of density 800 kg.m3and viscosity 0.002 Pa s flows upwards through the bed, which is restrained at its upper surface.(a) Calculate the voidage (volume fraction occupied by voids) of the bed.(b) Calculate the frictional pressure drop across the bed when the volume flow rate of liquid is 1:44m3/h.
Estimate the terminal settling velocity in water at a temperature of 15°C of spherical silicon particles with specific gravity 2.4 and average diameter of 0.05mm. Assume p=999 kg/m3 and p= 0.00113 Ns/m2
An irregular lump of saturated clay with a mass of 605.2 g was coated with paraffin wax. The total mass of the coated lump (in air) was 614.2 g. The volume of the coated lump was found to be 311 ml by displacement in water. After carefully removing the paraffin wax, the lump of clay was over-dried to a dry mass of 479.2 g. The specific gravity of the hardened wax is 0.90. Determine the water content, specific gravity, dry unit weight and void ratio.
• Q-3. Settling characteristics of a conceritrated suspension C = 3000 mg/t were deterrmined in a laboratory study. The suspension was settled in a colurmn 100-centimeters high, aind thé height of the interface h, was recorded with tirme Time, minutes 100 79 60 10 15 38 20 25 23 15 30 12 35 40 50 7.5 Calculate the area required to achieve clarification and to yield a thickeried sludge concentration of 25,000 mg/f- for an inıfluent flow rate of 5 mgd.
Ex.6: Drilling mud with 16 ppg density. The volume percentage of solids in it is (32%). Calculate the percentage of each on in the mud.
Estimate the teminal settling velocity in water at a temperature of 15 °C of spherical silicon particles with specific gravity 2.40 and average diameter of 0.05 mm. Assume p =999 kg/m? and u = 0.00113 N sm².
Q3.Define the substitutional solid solution types with diagram.