The single-line diagram of a three-phase power system is shown in below Figure. Equipment ratings are given as follows: Synchronous generators: 1000 MVA 1000 MVA 500 MVA 750 MVA GI G2 G3 G4 Transformers: TI T2 T3 T4 1000 MVA 1000 MVA 500 MVA 750 MVA Transmission lines: 1-2 1-3 2-3 b) c) 500 kV 500 kV 500 kV d) 15 kV 15 kV 13.8 kV 13.8 kV Xd=X₂= 0.18, Xo = 0.07 per unit Xd=X₂=0.20, Xo = 0.10 per unit Xd=X₂-0.15, Xo = 0.05 per unit Xa=0.30, X₂=0.40, Xo= 0.10 per unit 15 kV A/500 kV Y 15 kV A/500 kV Y 15 kV Y/500 kVY 15 kV Y/500 kV Y a) The inductor connected to Generator 3 neutral has a reactance of 0.05 per unit using generator 3 ratings as a base. Draw the zero-, positive-, and negative-sequence reactance diagrams using a 1000-MVA, 500-kV base in the zone of line 1-2. Neglect the A-Y transformer phase shifts. X=0.10 per unit X=0.10 per unit X=0.12 per unit X=0.11 per unit Χι = 50 Ω, Χ@ = 150 Ω Χρ = 40 Ω, Χο = 100 Ω Χι = 40 Ω, Χ@ = 100 Ω Faults at bus 1 are of interest. Determine the Thévenin equivalent of each sequence network as viewed from the fault bus 1. Prefault voltage is 1.0 per unit. Prefault load currents and A-Y transformer phase shifts are neglected. (Hint: Use the Y-A conversion.) Determine the subtransient fault current in per-unit and in kA during a bolted three-phase fault at the fault bus 1. Determine the subtransient fault current in per-unit and in kA, as well as the per-unit line-to-ground voltages at the fault bus for bolted single line-to-ground fault at the fault bus 1.
The single-line diagram of a three-phase power system is shown in below Figure. Equipment ratings are given as follows: Synchronous generators: 1000 MVA 1000 MVA 500 MVA 750 MVA GI G2 G3 G4 Transformers: TI T2 T3 T4 1000 MVA 1000 MVA 500 MVA 750 MVA Transmission lines: 1-2 1-3 2-3 b) c) 500 kV 500 kV 500 kV d) 15 kV 15 kV 13.8 kV 13.8 kV Xd=X₂= 0.18, Xo = 0.07 per unit Xd=X₂=0.20, Xo = 0.10 per unit Xd=X₂-0.15, Xo = 0.05 per unit Xa=0.30, X₂=0.40, Xo= 0.10 per unit 15 kV A/500 kV Y 15 kV A/500 kV Y 15 kV Y/500 kVY 15 kV Y/500 kV Y a) The inductor connected to Generator 3 neutral has a reactance of 0.05 per unit using generator 3 ratings as a base. Draw the zero-, positive-, and negative-sequence reactance diagrams using a 1000-MVA, 500-kV base in the zone of line 1-2. Neglect the A-Y transformer phase shifts. X=0.10 per unit X=0.10 per unit X=0.12 per unit X=0.11 per unit Χι = 50 Ω, Χ@ = 150 Ω Χρ = 40 Ω, Χο = 100 Ω Χι = 40 Ω, Χ@ = 100 Ω Faults at bus 1 are of interest. Determine the Thévenin equivalent of each sequence network as viewed from the fault bus 1. Prefault voltage is 1.0 per unit. Prefault load currents and A-Y transformer phase shifts are neglected. (Hint: Use the Y-A conversion.) Determine the subtransient fault current in per-unit and in kA during a bolted three-phase fault at the fault bus 1. Determine the subtransient fault current in per-unit and in kA, as well as the per-unit line-to-ground voltages at the fault bus for bolted single line-to-ground fault at the fault bus 1.
Power System Analysis and Design (MindTap Course List)
6th Edition
ISBN:9781305632134
Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma
Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma
Chapter3: Power Transformers
Section: Chapter Questions
Problem 3.32P: Determine the positive- and negative-sequence phase shifts for the three- phase transformers shown...
Related questions
Concept explainers
Load flow analysis
Load flow analysis is a study or numerical calculation of the power flow of power in steady-state conditions in any electrical system. It is used to determine the flow of power (real and reactive), voltage, or current in a system under any load conditions.
Nodal Matrix
The nodal matrix or simply known as admittance matrix, generally in engineering term it is called Y Matrix or Y bus, since it involve matrices so it is also referred as a n into n order matrix that represents a power system with n number of buses. It shows the buses' nodal admittance in a power system. The Y matrix is rather sparse in actual systems with thousands of buses. In the power system the transmission cables connect each bus to only a few other buses. Also the important data that one needs for have a power flow study is the Y Matrix.
Types of Buses
A bus is a type of system of communication that transfers data between the components inside a computer or between two or more computers. With multiple hardware connections, the earlier buses were parallel electrical wires but the term "bus" is now used for any type of physical arrangement which provides the same type of logical functions similar to the parallel electrical bus. Both parallel and bit connections are used by modern buses. They can be wired either electrical parallel or daisy chain topology or are connected by hubs which are switched same as in the case of Universal Serial Bus or USB.
Question
Just part D
Transcribed Image Text:The single-line diagram of a three-phase power system is shown in below Figure.
Equipment ratings are given as follows:
Synchronous generators:
1000 MVA
1000 MVA
500 MVA
750 MVA
GI
G2
G3
G4
Transformers:
TI
T2
T3
T4
1000 MVA
1000 MVA
500 MVA
750 MVA
Transmission lines:
500 kV
500 kV
500 kV
1-2
1-3
2-3
a)
b)
c)
d)
15 kV
15 kV
13.8 kV
13.8 kV
Xd = X2= 0.18, Xo = 0.07 per unit
Xd = X2=0.20, Xo = 0.10 per unit
Xd = X2= 0.15, Xo = 0.05 per unit
Xd 0.30, X₂=0.40, Xo = 0.10 per unit
15 kV A/500 kV Y
15 kV A/500 kV Y
15 kV Y/500 kV Y
15 kV Y/500 kV Y
X = 0.10 per unit
X= 0.10 per unit
X = 0.12 per unit
X=0.11 per unit
Χρ = 50 Ω, Χ@ = 150 Ω
X₁40 S2, Xo= 100 2
X₁40 2, Xo 100 2
The inductor connected to Generator 3 neutral has a reactance of 0.05 per unit
using generator 3 ratings as a base. Draw the zero-, positive-, and negative-sequence
reactance diagrams using a 1000-MVA, 500-kV base in the zone of line 1-2. Neglect
the A-Y transformer phase shifts.
Faults at bus 1 are of interest. Determine the Thévenin equivalent of each
sequence network as viewed from the fault bus 1. Prefault voltage is 1.0 per unit.
Prefault load currents and A-Y transformer phase shifts are neglected. (Hint: Use the
Y-A conversion.)
Determine the subtransient fault current in per-unit and in kA during a bolted
three-phase fault at the fault bus 1.
Determine the subtransient fault current in per-unit and in kA, as well as the
per-unit line-to-ground voltages at the fault bus for a bolted single line-to-ground
fault at the fault bus 1.
Transcribed Image Text:Line 1-2
Line 1-3
2
2
T₂
Line 2-3
3
T3
38
TA
38
21 Ý
3
4
youthiy
Expert Solution
This question has been solved!
Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.
This is a popular solution!
Step 1: Given
VIEWStep 2: sequence compoenet for generators
VIEWStep 3: sequence compoenet for generators
VIEWStep 4: Sequence compoenet for transformer and tranmission line
VIEWStep 5: Positive sequence diagram and equivalent reactance
VIEWStep 6: Negative sequence diagram and equivalent reactance
VIEWStep 7: Zero sequence diagram and equivalent reactance
VIEWStep 8: Fault current
VIEWStep 9: pu line to ground voltages at fault bus
VIEWSolution
VIEW
Trending now
This is a popular solution!
Step by step
Solved in 10 steps with 14 images
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.Recommended textbooks for you
Power System Analysis and Design (MindTap Course …
Electrical Engineering
ISBN:
9781305632134
Author:
J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma
Publisher:
Cengage Learning
Power System Analysis and Design (MindTap Course …
Electrical Engineering
ISBN:
9781305632134
Author:
J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma
Publisher:
Cengage Learning