The simply supported concrete beam shown in the figure has an effective depth of 600 mm and a sectional width of 300 mm. If fc= 28 MPa and fy=420 MPa, then :answer the following questions: 1-he spacing of Ø10 mm stirrups at the critical section from the face of support A equals =, mm (round to * the nearest integer number 2-The spacing of Ø10 mm stirrups at the critical section from the face of support Bequals. .mm (round to the * nearest integer numbe 100 kN/m A 6 m 8 m

The simply supported concrete beam shown in the figure has an effective depth of 600 mm and a sectional width of 300 mm. If fc= 28 MPa and fy=420 MPa, then :answer the following questions: 1-he spacing of Ø10 mm stirrups at the critical section from the face of support A equals =, mm (round to * the nearest integer number 2-The spacing of Ø10 mm stirrups at the critical section from the face of support Bequals. .mm (round to the * nearest integer numbe 100 kN/m A 6 m 8 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the largest torque T which may be applied to end of the solid bar which is shown in the diagram below, knowing that the maximum allowable shear stress = 107MPa and G = 40GPa. Provide your answer in kNm with precision to two decimal points. B 40 mm TABLE 3.1. Coefficients for Rectangular Bars in Torsion a/b C₁ C₂ 1.0 0.208 0.1406 1.2 0.219 0.1661 60 mm 1.5 0.231 0.1958 2.0 0.246 0.229 2.5 0.258 0.249 3.0 0.267 0.263 4.0 0.282 0.281 5.0 0.291 0.291 N 10.0 0.312 0.312 مة 0.333 0.333
A prestressed beam is given in the figure below. Aps = 720 mm² H = 600 mm B = 400 mm y = 100 mm If the initial prestress is fps,i = 1,208 MPa, calculate the stress at the top fiber, at midspan section due to prestress only. Input the answer in MPa, wtih 2 decimal places including the sign. + for tensi for compression. Aps mm B (mm) II (mm) y (mm) L (m)
Answer in two decimal places please
PROBLEM 3 340 mm The plates are connected by 9-20 mm bolts. Force F = 5Ở KN are applied at both plates in opposite directions as shown in Figure 3. Compute the following: A. Axial stress of each plate. B. Shear stress of each bolt. Assume that each bolt resists the applied force equally. %3D +F 150 mm 中 F 50 mm 340 mm Figure 3: Bolted Plates
can you write the answer please
Both ends of the beam are guided or slider support not Fixed support. Plz, solve this problem using stiffness Method and show all the step and alsi draw SFD and BMD My last two digits of my reg.no: 95 Structural Analysis-2
Fig shows a 700 mm length of aluminum alloy bar is suspended from the ceiling such away to provide a clearance of 0.3 mm between it and a 250 mm length of steel bar as shown in figure. Aal = 1250 mm² Eat =70 GN/m²; A = 2500 mm², E, = 210 GN/m². Find the stress in the aluminum and in the steel due to a 300 kN load applied 500 mm from the ceiling. 0.3 mm- 250 mm 500 mm 200 mm 300kN o Steel Aluminum M N
Can you help me to solve this question please ? Thank you!
Vn = 6*36*1/(4*1.1) = 49.09 am I wrong? I believe in the calculation in the solution the coefficient m was not taken into account. And Pn is not 54 kips either, with the given formula it comes up as 6*36*0.5/(4*1.25) = 21.6 and in which case the design strength would be 21.6 kips. Please let me know if there's something I'm missing from the formulas.
A stat of stress is specified in Figure. By using Mohr's circle determine the normal and shearing stresses on (a) the principal planes, (b) the planes of maximum shearing stress. 20 MPa 32 MPa 10 MPa 10 MPa 32 MPa 20 MPa I need a clear answer by hand, not by keyboard and fast answer within 20 minutes. Thank you | dybala
A 3 m long beam has a 4 kN/m distributed load applied to the cantilever steel beam as shown below. The dimensions for a = 40,b= 40, c = 40, and d = 100. a w kN/m >a d Section a-a (unit in mm) Mc M 1_M FORMULAS: 06 = or == " I S P EI L b C
Situation 2: A steel rod is inserted into a wooden block as shown. Further, two cables (one on each end) are attached to the rod where it carries a bar with negligible weight. Determine the maximum allowable force P in Newtons based on the stress and strain parameters given below. Wooden Block: Shear strength capacity = 10 MPa Bearing strength capacity = 15 MPa Normal strength capacity = 40 MPa Steel Rod: Shear strength capacity = 15 MPa 40 mm 2500 mm 100 mm 120 mm 'I 220 mm 12 mm dia.