The simply supported beam with a rectangular cross-sectional area is designed to support the loading as shown in Figure Q3. i) Calculate the reactions at A and B. ii) Draw the shear force and bending moment diagrams for the beam. ii) Determine the maximum normal stress and shear stress due to bending. 3 kN 3 kN 450 N • m 100 mm B D E 80 mm 300 mm 300 mm 200 mm

Q: how to measure cylinder taper and out of round

A: Cylinder out of Round is the difference of diameter when measured parallel to the crankshaft and…

Q: Feeler gauge is used to measure the Select one: O a. Screw pitch O b. Surface Roughness O C. Radius…

A: Feeler gauge is used for measuring the gap widths. Feeler gauges are mostly used in engineering to…

Q: I need isometric view please correct

A: The required isometric view is drawn with 1 Grid= 1 Unit

Q: Explain in details how to calibrate the WAX Bath

A: Given Wax bath To find Calibration technique

Q: Why must a cylinder ridge be removed before attempting to remove the piston?

A: Cylinder ridge reamer is a component use to remove the ridge.

Q: This part of the a cylinder holds the piston in place and helps support the rod as it extends. a.…

A: Option c is correct.

Q: Define lateral and radial runout

A: Runout:-  Runout is an inaccuracy of rotating mechanical systems , in other words the tool or shaft…

Q: Find the two-dimensional temperature distribution T(r,z) under steady state condition. Where, To=20…

A:

Q: Mention the basic flame types a

A: Given: Basic Flame types

Q: The tooth height is defined by the sum of addendum and the dedendum Select one: True False

A: Tooth height in gear is defined as the radial distance between the addendum and dedendum circle of…

Q: A low Reynolds number will result in a precipitate a. Bad sort b. Good sorting c. round c. Uncertain

A: A low Reynolds number will result in a precipitate  Good sorting.

Q: 40. Worn cylinders can be reconditioned by-- a. None of the below b. Machining in the lathe c.…

A: Solution:   Note: Dear Student! As per our guidelines, we are only allowed to answer three sub-parts…

Q: 1.Name type of failures in engine blocks

A: The engine is the most important part of the IC engine. In production, Every company produces an…

Q: 5 ft 2 ft 7 ft The train has a weight of 23000 Ib and a center of gravity at G. It is suspended from…

A: Free Body Diagram for the given condition can be made as shown below: All normal reactions are…

Q: How are single-acting cylinders retracted?

A: To find : How are single-acting cylinders retracted?

Q: What material is the piston? None of these answers are correct Steel Cast iron O Aluminum

A: Given:   To select the correct option for the material of the piston.

Q: Which of the following pressure is the highest? a. 25x10-4 Pascal b. 45 micro Pascal c. 0.03…

A:

Q: Please all solve the problem

A:

Q: Worn teeth on a speed gear can cause?

A: worn teeth creates a big problem in gear drive.

Q: The rotation angle of the joints is still needed.

A:

Q: Acidizing removes damage near wellbore by injecting fluid into the formation above the fracturing…

A: Option b is correct  True

Q: What is the maximum gas flow rate for a nozzle size?

A: GIVEN; What is the maximum gas flow rate for a nozzle size?

Q: Given two oil According to the standard by Society Automotive Engineers the oil , by comparing the…

A: Given: Given two oil According to the standard by Society Automotive Engineers the oil , by…

Q: The velocity of flow increases when valve openings decreases Select one: O True O False

A: True Velocity of flow increases when valve openings decreases

Q: Draw three views of the adjusting bracket. . Orill-2 Holes 3 BOrill

A: The figure below shows the top and front view of the given model.

Q: Design a piston for use in automobile engines (piston ring, pin, skirt).

A:

Q: When pressurized fluid enters the cap end of a double-acting cylinder, the rod will retrac

A: GIVEN DATA - A MCQ GIVEN ABOUT DOUBLE ACTING CYLINDER

Q: how did you get the 3038Pa in static pressure?

A:

Q: False

A: It is False. Higher the gauge number, indicates thinner the sheet metal.

Q: State and draw two methods used to mount cylinders?

A:

Q: specific weight is also known as weight. select one: True False

A: Answer: False

Q: Riser is designed so as to ?

A: Riser is part of gating system in casting process. The gating system includes pour basing, sprew,…

Q: Which tool steel group would be the best for master gauges? D M P S

A: Given :-  Which tool steel group would be the best for master gauges? D M P S

Q: Which type of oil ring is slotted so that excess oil canpass through it?a. Cast ironb. Segmentedc.…

A: A compression ring is the seal that keeps leaks from pipe segments with a bell-shaped orifice at…

Q: 3 Questions 1. Describe the Petrol Engine?

A:

Q: What was the orginal size of the smallest outside diameter?

A: Data given-

Q: Definition of bottom dead centre

A:

Q: Wipers pads on lathe machines are used between slides and slideways designed to be cleaned by…

A: The given statement is false.

Q: A kick occurs because the pressure inside the wellbore annulus is higher than formation pressure. a.…

A: The kick formation depend on the pressure gradient in wellbore annulus and formation pressure.