The simple span T-beam is part of a floor system of span length 6 m. and beam spacing 1125 mm on centers. The bars are placed with 25 mm clear space between łayers. It is reinforced with 10 – 28 mm ø bars placed in two rows. The width of web section is 600 mm with a tota! depth of 1000 mm. Słab thickness is 162.5 mm. Diameter of stirrups is 10 mm ø. Use 40 mm clear cover for reinforcements. f' = 20.7 MPa, fy = 414.6 MPa. Q Compute the depth of compression block. ® Compute the practical moment strength ø Mn. ® How much steel would be required in this beam cross section to make the compressive steel block just completely cover the flange?

The simple span T-beam is part of a floor system of span length 6 m. and beam spacing 1125 mm on centers. The bars are placed with 25 mm clear space between łayers. It is reinforced with 10 – 28 mm ø bars placed in two rows. The width of web section is 600 mm with a tota! depth of 1000 mm. Słab thickness is 162.5 mm. Diameter of stirrups is 10 mm ø. Use 40 mm clear cover for reinforcements. f' = 20.7 MPa, fy = 414.6 MPa. Q Compute the depth of compression block. ® Compute the practical moment strength ø Mn. ® How much steel would be required in this beam cross section to make the compressive steel block just completely cover the flange?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Bearing P plate Let the allowable stresses in the post be ost=120MPaand oco=6MPA. Compute the maximum safe axial load P that may be applied. The moduli of elasticity are 200 GPafor steel and 14 GPafor a concrete. Each steel bar has cross-sectional area of 900mm2. Steel - Concrete - 300 mm 300 mm
2 A simply supported beam has a dimension of 300mmw x 600mmh has a span of 6m. it has a superimposed load of 30KN/m and live load of 50KN. It has a specified concrete strength of 28MPa and yield strength of 420MPa. Distance of centroid steel area to outermost fiber is 60mm. a. What is the maximum moment of the beam? b. What is the required tension steel area? Use et = 0.004
AT:Design the steel reinforcement for flexural for the beam shown in the kN fig.below The dead load on the beam is 100 (not include self weight) & the live load is 200KN. useØ25mm& Use effective cover in top& bottom=60mm, use fc' = 27.6 Mpa, fy= 414Mpa. Ptive=200KN kN D.L= 100 d= 550mm 275mm 3m Зт
10 mm | | | | 10 mm 50 mm ارت - 50 mm 10 mm 20 kN B 150 mm 910 mm 10 kN D ------- 150 mm Two vertical forces are applied to a am of the cross section sh vn. Determine the maximum tensile and compressive stresses in portion BC of the beam.Show your complete solution and box your answer.
2. Use the method of sections to determine the forces in members AB, FG, AH, and GH. State whether the forces are in tension or compression. -2.5 m 2.5 m- 2.5 m 5 kN 3 kN 2 kN A hleck..ha ma of 1E0 L nable hinh na unra 1E0 mm
A reinforced concrete beam is 250 mm wide with an effective depth of 400 mm. Use f'c= 21 MPa and fy = 275 MPa. The section is reinforced with 4 - $25mm bars. U = 1.2D + 1.6L. a. Compute for the nominal flexural strength. b. Calculate the design flexural strength of the section. c. Calculate the safe service live load moment if the service moment from total dead load is 96 kN-m. d. If the beam is 5m long with a moment from total dead load of 96 kN-m, find the maximum moving concentrated service live load that can be supported by the beam.
A horizontal tension member is to be constructed of two pieces of plastic glued along the incline pq at an angle of 30 deg with the horizontal. The allowable stresses on the glued joint in tension and shear are 5MPa and 3MPa respectively. Determine the largest load P. Assume that the strength of the glued joint controls the design. The cross-sectional area of the bar is 225 mm². - Need asap pls.
Determine the force in member AB of the truss below. Indicate as positive if the member is in tension and negative (-) if the member is in compression. Provide the answer in kips t H 1.5 k F 2 k 2 k G B C . 8 ft 8 ft -8 ft 8 ft E D 4 ft Q Search securySearch 5 17 & 8
A traffic light signal pole is subjected to the weight of each traffic signal 45 lbs and the weight of the road lamp 55 lbs . The weight of lateral arms is included in the signal and lamp weights. The people is fixed and the base and is made of round structural steel section HSS 14.000 x 0.25. The details of the pole section may be obtained form the Manual of American society of steel Construction (AISC Steel Manual). Analyze the principle normal stresses and the maximum shear stresses on elements A and B located at the base in the pole as shown in the sketch below.
the T-beam is reinforced with an unbonded tendon having an area Aps=1000 sq. mm., fc'=35 MPa, Fpu= 1800 MPa, Fpy= 1620 MPa and the effective stress after losses is Fpe= 1100 MPa. The beam has a simple span of 6 m, b= 2500 mm, hf= 80 mm, bw= 300 mm, dp= 800mm and h= 900 mm. Compute the stress in prestressed reinforcement at nominal strength. Compute the depth of compression block. Compute the moment capacity of the beam.
Situation 14 - Using method of sections, determine the internal force. of members 2-3 and 2-5. Use L = 1.5 m and P = 5 kN 4L 3L 3L 3L 20 3 نی 4 P P 3P 13P L
HiW@ Draw S.f.n and BiMin for beam shown by Naphial methds Anst hinge %3D M= 9 W.m 3m 2m 3m Mmny = -6 IW.m