The root diameter of a double square thread is 0.55 in. The screw has a pitch of 0.2 in. Find the outside diameter, the number of threads per inch, and the lead.

Q: Buttress threads are used for withstanding high forces in one direction only. Select one: True False

A: Buttress threads is a design of screw thread in which leading faces are perpendicular to screw axis…

Q: Q4: Determine the plate thickness if the rivet diameter was 10 mm?

A:

Q: 8-1 A power screw is 25 mm in diameter and has a thread pitch of 5 mm. (a) Find the thread depth,…

A:

Q: The triple thread screw has a lead of 15 mm. Determine its thread per inch.

A: Given               Lead, L = 15 mm                           = 0.59 in No of thread, n = 3 Find…

Q: 10. What is the minimum diameter in mm of a steel shaft which will be used to operate a 14 kN-m…

A:

Q: Problem 6 You've been asked to design a stamping tool as shown. What are the internal forces at A…

A: FBD

Q: Compute the lead angle of M16 x 1.2 thread

A:

Q: A 3/8-inch diameter bolt is subjected to a 2,135-lb tensile load. The bolt passes through a very…

A:

Q: Find the pitch in mm for an external thread, if  the depth of thread is 5 mm. Pitch (in mm) =

A:

Q: Write the formula used to determine the average shear stress?

A: shear stress is the stress produced due to shear force.

Q: The rectangular piece of wood, 72 mm by 193 mm, is used as a compression block. The grain of the…

A: GivenA=72mm×193mmθ=16.3oσallowable=28.5MPa

Q: y=23 76 M=2 Find a,6, u

A: Given, Z1  = 23 Z2  = 76 m = 2   For d1 = Z1m = 23 * 2 = 46 For d2 = Z2m = 76 * 2 = 152 For a =…

Q: 6. Four cylinders rolling in opposite directions has a speed ratio of AB.C:D = 5:2:3:4. If center…

A: Let the diameters of each cylinders be - DA, DB, DC and DD . The center distance is given by -DA2+…

Q: An elastic member 16.6 mm thick is glued in between two rigid members. Considering a shear force of…

A:

Q: A 5-m hollow steel shaft (G= 80 GPa) is subjected to a 25 kN-m torque. The outer diameter is 200 mm.…

A: Given data:- Length of shaft =5-m G=80 GPa Torque (T)=25 kN-m The outer diameter (D) = 200 mm. The…

Q: A metric thread of pitch 2 mm and thread angle 60° is inspected for its pitch diameter using 3 wire…

A: Given:Pitch, P=2 mmThread angle, 2θ= 60oθ=30o

Q: 2. The composite shaft of total length 1.8 m consists of 5 mm thick brass and is fixed to a 30 mm…

A:

Q: The thread depth is  measured along the ----------------- of the thread. Pitch Crest Angles Face

A: Thread: A thread is a simple machine structure mainly used to convert the the linear motion of force…

Q: Determine the major diameter limits (upper and lower) for the following thread using the Machinery's…

A: Here we have given thread ½-20 UNF 2A and need to find out its  major diameter limits i.e. Upper and…

Q: I need the answers to this question.

A: The explanation of the above terms have been explained below.

Q: Find Pitch(in mm) , if Minor diameter is 27 mm and Nominal diameter is 33 mm for an internal thread.…

A: Given: Dnominal=33 mm Dminor=27 mm To Find: Pitch

Q: The solid spindle AB is made of a steel with an allowable shearing stress of 12 ksi, and sleeve CD…

A: Spindle AB is made of steel with allowable shearing stress of Sleeve CD is made of brass with…

Q: Compute the lead of an M16x 1.6 double thread

A:

Q: 3. Two ½ in. thick A36 steel plates are joined with two % in. thick A36 steel splice plates and…

A: It is asked to find the smallest bolt size to support the load of 55 kips

Q: Determine the distance of O (shear center) to the center of mass A in base unit with 1 digits after…

A: Given:The radius to the center of the thickness, The thickness of the circular section,

Q: If you have a rod with an initial diameter 12 mm, final diameter is 10 mm and yield stress 40Mpa, it…

A:

Q: What is the axis yielding?

A: A yielding is phenomena of give up to something like external pressure. to yield something does not…

Q: List down the formulas for calculating the shear stress and angle of twist of the following cross…

A: It is asked to write the shear stress and angle of twist formula for the cross-sections of shape…

Q: For an internal thread, If the 3.75mm pitch and Tap drill size is 12 mm. Find the Nominal diameter.…

A: pitch=3.75 mm  tap drill size =12mm nominal diameter =?

Q: Please be sure . If the MMC for a hole is .2500'' and the MMC for the shaft is .2498, the allowance…

A: Allowance: 1. It is a Minimum clearance or maximum interference between the assembly of shaft and…

Q: In an external thread the root diameter can be calculated by the following expression   OD-2X…

A:

Q: Two in. thick A36 steel plates are joined with two % in. thick A36 steel splice plates and twelve…

A: It is asked to find the smallest bolt size to support the load of 55 kips

Q: The outside diameter of a hollow shat is 1.6 times the inside diameter. When transmitting 420 W of…

A:

Q: Can you give a more detailled explanation for part C and answer to the following question please:…

A: Given

Q: lestion IJ alculate the maximum stress in 0.10-i 2.00-in dia. Applied torque %3D

A:

Q: 15-1 Compare the tensile load capacity of a 5/16-18 UNC thread and a 5/16-24 UNF thread made of the…

A: The tensile load capacity is the product of the tensile stress and the cross-section area. As the…

Q: For the cross section in problem 1 (which is also shown below), you are asked to determine the…

A:

Q: For an internal thread, If the 3.75mm pitch and Tap drill size is 12 mm. Find the Nominal diameter.…

A: Given data: -  The pitch is P = 3.75 mm. The tap drill size is T = 12 mm.

Q: 8. A solid steel shaft 5 m long is stressed to 60 MPa when twisted through 4". Find the shaft…

A:

Q: 2. A flange coupling is to connect two 57 mm shafts. The hubs of the coupling are each 111 mm in…

A: According to our guidelines ,we are supposed to answer 1st three sub parts ,Please repost other…

Q: (a) Find Depth of cut and Root diameter for M18 x 2.75 x 30 internal thread.

A: Given:- M18 x 2.75 x 30   To find:- Depth of cut Root diameter

Q: wo shafts having the same length and material are joined in series. If the ratio of the diamete

A: Given Data⇒ Material and length of shaft is same.  Ratio of the diameter of the first shaft to that…

Q: Determine the vertical displacement of joint C . EA is constant

A: The vertical displacement of the joint C. FBD: The free-body diagram of the joint C is shown below.

Q: 7- Give the true representation of screw thread from the following, and mark the reasons for it. !!…

A: Given: Select the true representation of screw thread.

Metrology of Screw Threads

Screw threads are a series of ridges having the profile of a helix. This helix profile runs continuously along the length of a uniform solid or a hollow bar of a circular cross-section at periodic intervals. These helix ridges are also formed over a conical bar. These continuous helical ridges are termed threads.