The rigid bar ABC as shown in the figure is pinned supported at B and attached to the vertical two rods. Initially, the bar is horizontal and the vertical rods are stress- free. The temperature in the steel rod is decreased by 42°C. Neglect the weight of the bar Steel L = 900 mm A = 300 mm² E = 200 GPa a = 11.7 x 106/°C ΔΥ = -42°C 1m 3m Aluminum L=1320 mm A = 1200 mm² E = 70 GPa a = 23 x 10-6/°C Determine the deformation at steel if we will consider only the effect of change in temperature.

The rigid bar ABC as shown in the figure is pinned supported at B and attached to the vertical two rods. Initially, the bar is horizontal and the vertical rods are stress- free. The temperature in the steel rod is decreased by 42°C. Neglect the weight of the bar Steel L = 900 mm A = 300 mm² E = 200 GPa a = 11.7 x 106/°C ΔΥ = -42°C 1m 3m Aluminum L=1320 mm A = 1200 mm² E = 70 GPa a = 23 x 10-6/°C Determine the deformation at steel if we will consider only the effect of change in temperature.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rigid bar of negligible weight is supported and loaded with 70 kN, compute the temperature change AT (°C) that will cause the stress in the bronze rod (L = 1.5 m, A = 300 mm?, and E = 83 GPa) to be 50 MPa. Assume a = 18.9 µm/(m°C) for bronze and 12.8 um/(m°C) for aluminum (L = 3 m, A = 750 mm2, and E = 70 GPa). Aluminum Bronze 2.5 m 1.5 m 70 kN
Problem 1 An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown. Axial loads are applied at the positions indicated. Aluminum Steel A=800mm2 A=1000mm2 Bronze A=700mm? 4P 2P 500mm 600mm 700mm 1. What is the maximum value of P that will not exceed the axial stress bronze of 105 MPa? 2. What is the maximum value of P that will not exceed the axial stress in aluminum of 90 MPa? 3. If P=10KN, what is the axial force to be carried by the aluminum in KN? 4. If P is 5KN, what is the axial stress of steel?
1. At a temperature of 5°C, a 3-mm gap exists between the end of polymer bar (1) and support A as shown. Bar (1) is 50 mm wide and 20 mm thick (E = 800 MPa, a = 140 x 10-6/°C). Bar (2) is 75 mm wide and 25 mm thick (E = 2.7 GPa, a = 67 x 106/°C). The supports at A and C are rigid (i.e., fixed). Determine: a) the temperature at which the normal stress in bar (2) will be equal to -3.0 MPa, and b) the lengths of the two polymer bars at this temperature. (1) 3-mm gap 50 mm 500 mm B 75 mm 400 mm (2)
P = 300N ، a=140mm , b=240mm , d=26mm
An aluminum bar having a cross-sectional area of 160 mm carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E = 70000 MPa. The length of each bars are follow: B1 = 0.8 m; B2 = 1.0 m; B3 = 0.6 m. Determine the total deformation of the bars B1, B2 and B3 in mm. 35KN B1 B2 B3 10KN 15KN 30KN 2.5 B 1.79 C) 0.54 3.75 E 4.83
Determine the normal stress and change in length of the aluminum rod if the temperature was raised by 125°C. The 0.5-mm gap exists at 20°C. q = 5 t = 0
Knowing that a 0.02in gap exists when the temperature is 75°F, determine (a) the temperature at which the normal stress in the aluminum bar will be equal to -11ksi, (b) the corresponding exact length (2 decimal places in 103 inches) of the aluminum bar. 0.02 in. 14 in. Bronze A = 2.4 in² E = 15 × 106 psi a = 12 x 10-6/°F 18 in. Aluminum A = 2.8 in² E = 10.6 × 106 psi a = 12.9 x 10-6/°F
In the figure, determine the normal stress and change in length of the aluminum rod if the temperature was raised by 126°C. The 0.5-mm gap exists at 25°C. 0.56 mm 366 mm 255 mm Aluminum A = 2TTT mm² E = 75 GPa x = 23 x 10*/°C B Stainless Steel A = 8QQ mm² E = 190 GPa α = 17.3 x 10/°℃
In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to increase 20 x 103 mm while those at CD decrease 60 x 103 mm in the 230- mm-gage length. Using E = 180 GPa, determine the flexural stress at the top fiber. Answer must be in MPa. Given: a = 40 mm, b = 130 mm, and c= 70 mm. gage length a mm A B. b mm c mm
Two polymer bars are connected to a rigid plate at B, as shown. Bar (1) has a cross-sectional area of 1.21 in.? and an elastic modulus of 2350 ksi. Bar (2) has a cross-sectional area of 1.032 in.? and an elastic modulus of 4100 ksi. Assume L1=20 in., L2=49 in., Q=7.1 kips, P=2.9 kips, and R=12.9 kips. Determine the horizontal deflection of end C relative to end A. P (1) (2) C В L1 L2 Answer: uc/A in. %3D