The required no-load voltage ratio in a 150 kVA single-phase 50 Hz core-type, two-winding transformer is 5000/250 V. Calculate the load kVA for maximum efficiency. The full-load I2R loss is 1800 W and the core loss is 1500 W

The required no-load voltage ratio in a 150 kVA single-phase 50 Hz core-type, two-winding transformer is 5000/250 V. Calculate the load kVA for maximum efficiency. The full-load I2R loss is 1800 W and the core loss is 1500 W

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.32MCQ

See similar textbooks

Related questions

Q: 1. Explain the working principle of a transformer under no-load condition by referring to the…

A: A Transformer is a Power electrical device which is used to transfer power from one transmission…

Q: An 11,000/230-V, 150-kVA, 50-Hz, 1-phase transformer has a core loss of 1.4 kW and full-load Cu loss…

Q: 2. A 3-phase, 6,600/415-V, 2,000-kVA transformer has a per unit resistance of 0.02 and a per unit…

Q: Assignment 2 A 60-Hz 20-kVA 2400/240-V-rms transformer has the following equivalent-circuit…

A: Given f=60 HzV1=2400V2=240 Calculating transformer ratio a=V1V2a=2400240a=10

Q: iii. No-load current 3. If the ratio of V/F has been kept constant and the observed value of…

A: Q.1) Explanation 1)When the frequency is lowered (for slower motor speed), the magnetic field…

Q: Draw and explain the scheme illustrating the principle of a transformer voltage U2 regulation…

A: OLTC (On-load tap changer transformer): The tap changer is a device that is tied to the power…

Q: 55 V / 220 V, 50 Hz single phase transformer, high voltage (secondary) windings are left idle and…

A: Winding resistance of the secondary referred to the primary, R2'=0.015 Ω

Q: Q2: A 4000/400 V, 10 kVA transformer has the following constants: Primary and secondary winding…

A: The transformation ratio of the transformer is determined as:

Q: 9- An 11,000/230-V, 150-kVA, 50-Hz, 1-phase transformer has a core loss of 1.4 kW and full-load Cu…

A: Given, Full load KVA, Sfl=150 kVA Core loss, Pi=1.4 kW Full load Copper loss, Pcu=1.6 kW Power…

Q: We wish to connect a 6 kVA, 120/240 V transformer as an autotransformer to a 120 V source to supply…

A: "Since you have posted a question with multiple sub parts we will solve first three subpart for you…

Q: Question 2: Determine the below parameters for the given transformer while switch is ON and OFF.…

A: Given

Q: 1) 10 kVA, single-phase, 2400-V:120-V, 60 Hz transformer has an equivalent impedance referred to LV…

Q: A 400-k VA, 2300 230, 60-hz transformer supplies a 0.8 lagging power-factor load whose KVA Is…

A: The efficiency of the transformer is given by the relation, Where, x = percent rated load…

Q: The required no-load voltage ratio in a 150 kVA single-phase 50 Hz core-type, two-winding…

A: The required no-load voltage ratio in a 150 kVA single-phase 50 Hz core-type, two-winding…

Q: Q.2 (a) Give TWO reasons why we must use transformer in electrical system. (b) A single-phase…

A: a) To reduce transmission line losses, transformers are utilised to boost up the input voltage.…

Q: (b) A 50-kVA, 2600/1300-V, single-phase transformer has a core loss of 780 W. The transformer has a…

Q: a. Find the full-load regulation of this transformer at a power factor of 0.8 lagging. b. Find the…

Q: step down transformer rated 2200:220 having an effective core area of 100sqcm. and has 120 turns on…

Q: 55 V / 220 V, 50 Hz single phase transformer, high voltage (secondary) windings are left idle and…

A: Referring the resistance at primary side, R1=0.026 Ωand the inductance at secondary side,X1=0.045…

Q: 2. Determine the core area, the number of turns and pos the tapping point for a 500-kVA, 50-Hz,…

A: In this question auto transformer is given....We have to find out core area , no of turns and…

Q: A 23 KVA, 2300/230 V, 60 Hz step down transformer has the following resistance and leakage reactance…

A: A transformer is an electrical machine which is used in AC circuit to either step up or step down…

Q: Two transformers A and B have the following data Transformer A: 6600/440 V, (250 KVA ) requires (…

Q: Q/ The efficiency of a 400-kVA, single-phase, 60-Hz transformer is 98.77% when delivering full-load…

Q: The short circuit losses of a 15 kV single-phase transformer are 700W. Given that the reduced…

A: TRANSFORMER: The transformer transfers power from one circuit to another circuit without a change…

Q: 2.2 A single phase transformer with its primary winding supplied from a 50 Hz supply has 100 turns…

Q: voltage per winding of the 220V/12V, 60 Hz single phase core transformer is 2V. If the maximum flux…

A: We know direct formula of per winding voltage. From that formula we will find out cross section…

Q: The following test data were obtained from short-circuit and open-circuit tests of a 50-kVA,…

A: Given data Apparent power is S = 50 kVA Voltage is V = 600 V frequency is f = 60 Hz a) Calculating…

Q: 3/The core of a 300-kVA, 15000/650 V, 50-Hz, 1-ph, core type transformer has across- section of 30…

A: In the given question we note that The core of = 300 KVA , 1500/ 650 V Cross section area is…

Q: Q1: During the separation of transformer core losses experiment: 1. Why should always keep the ratio…

Q: In the single-phase, three- winding, transformer, the primary current is equal to lo at the…

A: In this question we need to choose a correct option

Q: Q2: A Cockcroft-Walton type voltage multiplier has ten stages with capacitances, all equal to 1.5…

A: Solution- Given,n=10C=1.5μFVmax =800kVf=50HzI=8mA

Q: A 230/400 V single-phase transformer absorbs 35 W when its primary winding is connected to a 230 V,…

Q: 2. A single-phase, 50-Hz, core-type transformer's no-load voltage ratio is 1,200/440. If the maximum…

A: Since you have asked multiple questions , we will solve the first question for you . If you want any…

Q: A 500/100V, single-phase transformer takes a full load primary current of 4A. Neglecting losses,…

A: Given data, VS = 100 V. VP = 500 V. IP = 4 A. (a) The expression for full load secondary current…

Q: Two transformers A and B have the following data Transformer A: 6600/440 V, (250 KVA ) requires (…

A: According to question: The efficiency of transformer is maximum when iron loss (no load loss) is…

Q: Q Two transformers A and B have the following data Transformer A: 6600/440 V, (250 KVA ) requires (…

Q: A 10-kVA, 2300/230-V transformer is to be tested to determine its excitation branch components, its…

A: 10-kVA, 2300/230-V transformer Open and short circuit parameters given Voc = 2300 V Vsc = 48 V Ioc =…

Q: Answer by true or false * True False The secondary winding of current transformer should be a large…

A: TRANSFORMER: The transformer transfers power from one circuit to another circuit without a change…

Q: The primary and secondary windings of a 500-kVA, 11-kV/415-V, single-phase transformer have…

Q: 1. A 10 kVA, single-phase, 2400-V:120-V, 60 Hz transformer has an equivalent impedance referred to…

A: Dear student as per our guidelines we are supposed to solve only one question.kindly repost other…

Q: Two transformers A and B have the following data Transformer A: 6600/440 V, (250 KVA ) requires (…

A: Since you have asked multiple questions in a single request, we will be answering only the 1st…

Q: What is the level of the peak voltage at the secondary 1 (Vsecondary 1) and secondary 2 (Vsecondary…

Q: (a) Consider the concept of magnetic circuit to explain the effect of air gap on the flow of flux.…

Q: A 23 KVA, 2300/230 V, 60 Hz step down transformer has the following resistance and leakage reactance…

A: A transformer is an electrical machine which is used in AC circuit to either step up or step down…

Q: 5) The maximum efficiency of a 100 kVA, 6600/240 V, 60 Hz single phase transformer occurs at half…

A: The solution is given below

Q: 2.20 The nameplate on a 25-MVA, 60-Hz single-phase transformer indicates that it has a voltage…

A: NOTE: Since you have asked multiple question, we will solve the first question for you. If you want…

Q: The per-unit system calculations method allows to: Select one: O a. improve the efficiency of the…

A: In the power systems analysis, Per Unit values are defined for per phase only not for 3 phase . A…

Q: 4. A single-phase, 1000-kVA, 2400/8000-V, 60HZ distribution transformer has the following…

A: There are two questions in the given image. We will be able to answer only the 1st question.

Concept explainers

Single Phase Transformer

A single-phase transformer is a type of power transformer. It is an electrical device that accepts converts the single phase alternating power into single phase alternating power. In this power conversion the voltage is stepped up or down. If the voltage is stepped up, the current will be stepped down and if the voltage is stepped down, the current will be stepped up.

Question

The required no-load voltage ratio in a 150 kVA single-phase 50 Hz core-type, two-winding transformer is 5000/250 V. Calculate the load kVA for maximum efficiency. The full-load I²R loss is 1800 W and the core loss is 1500 W. Round your answer off to the nearest whole number

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The symbol shown is a(n) a. iron core transformer. b. auto transformer. c. current transformer. d. air core transformer.
Consider an ideal transformer with N1=3000andN2=1000 turns. Let winding 1 be connected to a source whose voltage is e1(t)=100(1| t |)volts for 1t1ande1(t)=0 for | t |1 second. A2- farad capacitor is connected across winding 2. Sketch e1(t),e2(t),i1(t),andi2(t) versus time t.
An ideal transformer has no real or reactive power loss. (a) True (b) False
For an ideal transformer, the efficiency is (a) 0 (b) 100 (c) 50
For an ideal 2-winding transformer, an impedance Z2 connected across winding 2 (secondary) is referred to winding 1 (primary) by multiplying Z2 by (a) The turns ratio (N1/N2) (b) The square of the turns ratio (N1/N2)2 (c) The cubed turns ratio (N1/N2)3
A single-phase, 50-kVA,2400/240-V,60-Hz distribution transformer has the following parameters: Resistance of the 2400-V winding: R1=0.75 Resistance of the 240-V winding: R2=0.0075 Leakage reactance of the 2400-V winding: X1=1.0 Leakage reactance of the 240-V winding: X2=0.01 Exciting admittance on the 240-V side =0.003j0.02S (a) Draw the equivalent circuit referred to the high-voltage side of the transformer. (b) Draw the equivalent circuit referred to the low-voltage side of the transformer. Show the numerical values of impedances on the equivalent circuits.
A single-phase step-down transformer is rated 13MVA,66kV/11.5kV. With the 11.5 kV winding short-circuited, rated current flows when the voltage applied to the primary is 5.5 kV. The power input is read as 100 kW. Determine Req1andXeq1 in ohms referred to the high-voltage winding.
Why is it important to reduce the moisture within a transformer to acceptable levels during transformer installation?
The ratings of a three-phase three-winding transformer are Primary(1): Y connected 66kV,15MVA Secondary (2): Y connected, 13.2kV,10MVA Tertiary (3): A connected, 2.3kV,5MVA Neglecting winding resistances and exciting current, the per-unit leakage reactances are X12=0.08 on a 15-MVA,66-kV base X13=0.10 on a 15-MVA,66-kV base X23=0.09 on a 10-MVA,13.2-kV base (a) Determine the per-unit reactances X1,X2,X3 of the equivalent circuit on a 15-MVA,66-kV base at the primary terminals. (b) Purely resistive loads of 7.5 MW at 13.2 kV and 5 MW at 2.3kV are connected to the secondary and tertiary sides of the transformer, respectively. Draw the per- unit impedance diagram, showing the per-unit impedances on a 15-MVA,66-kV base at the primary terminals.
Three single-phase, two-winding transformers, each rated 450MVA,20kV/288.7kV, with leakage reactance Xeq=0.10perunit, are connected to form a three-phase bank. The high-voltage windings are connected in Y with a solidly grounded neutral. Draw the per-unit equivalent circuit if the low-voltage windings are connected (a) in with American standard phase shift or (b) in Y with an open neutral. Use the transformer ratings as base quantities. Winding resistances and exciting current are neglected.
A 23/230-kV step-up transformer feeds a three-phase transmission line, which in turn supplies a 150-MVA,0.8 lagging power factor load through a step-down 230/23-kV transformer. The impedance of the line and transformers at 230kVis18+j60. Determine the tap setting for each transformer to maintain the voltage at the load at 23 kV.
A transformer has primary and secondary turns of 1250 and 125 respectively. It has core cross-sectionof 36 cm2 and its rms flux density is to be limited to 1.4 T (to prevent core saturation). Whatmaximum 50 Hz voltage can be applied on the primary side and the corresponding open-circuitsecondary voltage?The core has a mean length of 150 cm and its relative permeability can be assumed to be 8000. Whatwould be the rms exciting current when the transformer’s primary winding is excited at a voltage ascalculated above? Also calculate the magnetizing susceptance as seen from primary and secondarysides.If the transformer were to be excited at 60 Hz, 1. What should be the maximum primary voltage for thecore flux density limit not to be exceeded? 2. What would be the magnetizing susceptance as seen oneach side in this case?