Answered: A thin cylinder of inner radius 500 mm…

A thin cylinder of inner radius 500 mm and thickness 10 mm subjected to an internal pressure of 5 MPa. The average circumferential (hoop) stress in MPa is

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.13P: : A hollow, pressurized sphere having a radius r = 4.8 in, and wall thickness t = 0.4 in. is lowered...

See similar textbooks

Related questions

Q: A thin cylinder of inner radius 500mm and thickness 10mm is subjected to an internal pressure of 5…

Q: 100 kip 10 kip-ft The 4-in. diameter shaft shown above is made from a ductile brass alloy. Which of…

A: solution Given d=4 in

Q: A steel rod of 20 mm diameter passes centrally through a copper tube of external diameter 40 mm and…

Q: A thin hollow spherical container has a diameter 1 m and a thickness of 4 mm is subjected to an…

Q: A solid square steel bar is fixed at one end as shown, and is loaded with a 25 kg weight. If the…

A: given data;load=mg=25*9.81=245.25Nlimiting stress σ=27.24kpa=27240Pa=27240N/m2cross sectional…

Q: An L-shaped bracket lying in a horizontal plane supports a load F = 1kN. The bracket has a hollow…

A: Write the given information.

Q: 3. A cylinder with one closed end and one free end has an outer radius, b =260mm, and an inner radiu…

Q: Two loads P act as shown, one parallel to (x0) and another parallel to z0; each load P equals 1850…

A: GIVEN :- b1=85mmb2=130mmb3=60mmd=28mmP=1850N

Q: Q-1 ) A thin cylinder of inner radius 150 mm and thickness 9 mm is subjected to an internal pressure…

A: Data given - P = 9 MPa r = 150 mm Or d = 2 × r = 2 × 150 = 300 mm t = 9 mm

Q: Q3 - A thin-walled cylindrical vessel has an internal diameter of 1m and a thickness of 10 mm…

A: pressure:- Pressure is defined as the physical force exerted on an object. The force applied is…

Q: A thin copper tube, 14 mm internal diameter and 0,5 mm wall thickness has closed ends and rotates at…

Q: determine the tensile stress induced in the bolt.

A: For solution refer below images.

Q: Problem No. 3. The compound shaft has the following properties: G in both Segment 1 Segment 1 pipe…

Q: 5. Segment AB of the bar is a tube with an outer diameter of d1 and a wall thickness of 0.125 in.…

Q: A flanged bolt coupling consists of eight 10-mm diameter steel bolts on a bolt circle 400 mm in…

A: Given:no=8do=10 mmDo=400 mmni=6di=10 mmDi=300 mmFo=8000 N

Q: A solid steel bar with a diameter of 50 mm is subjected to three forces as shown in the figure,…

A: In the given problem, the main stresses will be developed at point B due to 1200N force which will…

Q: A closed-ended compound cylinder is formed by shrinking a steel [E = 200 GPa; v = 0.3] tube that has…

Q: Question attached

A: Given: q=425 kPa To determine: Vertical stress increased below column A Vertical stress increased…

Q: 4- A hollow tubular shaft is 1.5 m long and has an outer diameter of 75-mm. The shaft transmits the…

Q: 4. A force Q is applied to a rectangular member with a size of 300mm x 450mm. Q is located 37.5mm…

A: Find the stress at point C and D and also find the value of force Q.

Q: Que 1.23. A steel rod of 3 cm diameter is enclosed centrally in a hollow copper tube of external…

Q: A1 A uniform bar of length L and cross sectional area A is held vertically at the upper end and…

A: When a uniform bar is hanged hanged vertically, the weight of bar varies from zero to W. At tip, it…

Q: A steel cylinder is 160 mm ID and 320 mm OD. If it is subject to an internal pressure of 150 MPa,…

A: Given data Internal diameter of steel cylinder (Di) = 160 mm internal radius (ri) = 80 mm outer…

Q: A central horizontal section of a hook is a symmetrical trapezium of inner width =67.5mm and of…

A: Given:Inner width,bi=67.5 mmOuter width,bo=22.5 mmP=37.5 KNInner radius,Ri=52.5 mmh=90 mmOuter…

Q: A cylindrical tank steel pressure vessel 200mm in radius and 4.0m in length, is subjected to an…

Q: A body is subjected to a direct tensile stress of 300 MPa in one plane accompained by a simple shear…

A: Given data Direct tensile stress = 300 MPa Shear stress = 200 Mpa

Q: For the given stress element, consider the magnitude for oA, OB, and t to be 15.0 MPa, 40.0 MPa, and…

Q: Figure 5 shows a thick cylinder of 50 mm internal radius and 115 mm outer radius is subjected to an…

A: Given data Inner radius = 50 mmOuter radius = 115 mmInternal Pressure =60 MN/m2External Pressure =…

Q: A thin walled spherical shell is subjected to an internal pressure. If the radius of the shell is…

A: The formula for the hoop stress can be expressed as,

Q: 4. A thin cylinder of inner radius 500 mm and thickness 10 mm is subjected to an internal pressure…

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal…

A: For the Given system P = 9 kips Q = 5 kips R = 20 kips S = 30 kips stress limit in (1) = 19 ksi…

Q: 69. A disc of 600 mm diameter and uniform thickness is rotating at 3000 rpm. Calculate the maximum…

A: In this problem, a disc with a diameter of 600 mm and a uniform thickness is rotating at 3000 rpm.We…

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal…

Q: Calculate the smallest area of each cable if the stress is not to exceed 76 000 KPa in bronze and…

A: Given Data: The permissible stress in Bronze cable is, σ1=76000 kPa. The permissible stress in…

Q: The figure shows 16-mm diameter bolts used to hold two steel plates by fitting inside a cylindrical…

Q: Figure 1.1 shows the horizontal rigid bar ABC support by pin at A and steel cables BD and CD. Cables…

A: FBD,

Q: A steam turbine rotor is 160 mm diameter below the blade ring and 25 mm thick. The turbine is…

A: A steam turbine rotor has a diameter of 160 mm below the blade ring and is 25 mm thick.The turbine…

Q: 3-m long thin-walled tube has an equilateral triangular cross-section with a constant thickness of…

Q: For the assembly, find the stress in each rod if the temperature rises 30°C after a load W 120 kN is…

Q: A steel column of hollow circular cross section shown in Figure is supported on a circular steel…

Q: 5. Segment AB of the bar is a tube with an outer diameter of d1 and a wall thickness of 0.125 in.…

A: Given Allowable stress in rod AB = 3400 psi Outer diameter = d1 Inner diameter = d1 - 0.125…

Q: Determine the thickness of a steel air receiver with 30 in. diameter and pressure load of 120 psi,…

Q: A steel bar has a uniform cross sectional area of 300mm². Calculate the stress at member AB 1.6m…

Q: 3. A cylinder with one closed end and one free end has an outer radius, b =260mm, and an inner…

A: solutionwe have given in the question.outer radius (r0)=260mminner radius (ri)=55mminterval pressure…

Q: A steel cylindrical vessel is subjected to a pressure of 21 MPa. Its outer diameter is 4.6 m and its…

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

A thin cylinder of inner radius 500 mm and
thickness 10 mm subjected to an internal pressure
of 5 MPa. The average circumferential (hoop)
stress in MPa is

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
A fire extinguisher tank is designed for an internal pressure of 825 psi. The tank has an outer diameter of 4.5 in. and thickness of O.OS in. Calculate the longitudinal stress, the circumferential stress, and the maximum shear stresses (out-of-plane and in-plane) at the outer surface of the tank.
A hemispherical window (or viewport) in a decompression chamber (see figure) is subjected to an internal air pressure of 85 psi. The window is attached to the wall of the chamber by 14 bolts. (a) Find the tensile force Fin each bolt and the tensile stress (T in the viewport if the radius of the hemisphere is 14 in. and its thickness is 1.25 in. (b) If the yield stress for each of the 14 bolts is 50 ksi and the factor of safety is 3.0, Find the required bolt diameter. (c) If the stress in the viewport is limited to 500 psi, find the required radius of the hemisphere.
-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. a
A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded in biaxial stress by normal stresses r and cry. (sec figure). A strain gage is bonded to the plate at an angle 4 = 350 If the stress o is 10,700 psi and the strain means used by the gageise = 390 X 106.whatisthcmax- imum in-plane shear stress (Tr, ),. and shear strain (>‘ ).? What is the maximum shear strain (y ) in the x-: plane? What is the maximum shear strain (y ).. in the y-r plane?
‘7.3-11 The stresses on an element are sx= -300 psi and sy= 600 psi. Find the maximum shear stresses on the element and show them on a sketch of a properly oriented clement.
A single steel strut AB with a diameter (a) Find the strut force Fs and average normal stress ds= 8 mm supports the vehicle engine hood of a in the strut. mass 20 kg that pivots about hinges at C and D (see (b) Find the average shear stress t aver in the bolt at A,figure parts a and b). The strut is bent into a loop at (C) Find the average bearing stress bon the bolt at A. its end and then attached to a bolt at A with a diameter db= 10 mm. Strut AB lies in a vertical plane.
- A specimen used in a coupon test has norm al stress ??. = 15 MPa (see figure). Using Mohr’s circle, find the state of stress on the element oriented at angle ? = 20° and show the full stress state on a sketch of a properly oriented element.
: A hollow, pressurized sphere having a radius r = 4.8 in, and wall thickness t = 0.4 in. is lowered into a lake (see figure). The compressed air in the tank is at a pressure of 24 psi (gage pressure when the tank: is out of the water). At what depth D0will the wall of the tank be subjected to a compressive stress of 90 psi?
The state of stress on an element along the hydraulic lift cylinder on a truck is trv= — 5 MPaLFind the maximum shear stress on the clement and show the state of stress on a sketch of a properly oriented clement.
The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
Two sections of steel drill pipe, joined by bolted flange plates at Ä are being tested to assess the adequacy of both the pipes. In the test, the pipe structure is fixed at A, a concentrated torque of 500 kN - m is applied at x = 0.5 m, and uniformly distributed torque intensity t1= 250 kN m/m is applied on pipe BC. Both pipes have the same inner diameter = 200 mm. Pipe AB has thickness tAB=15 mm, while pipe BC has thickness TBC= 12 mm. Find the maximum shear stress and maximum twist of the pipe and their locations along the pipe. Assume G = 75 GPa.