The pulmonary artery, which pumps blood from the heart to the lungs, has an inner radius of 18.8 mm and is 4.82 cm long. If the pressure drop between the heart and lungs is 1,275 Pa, what is the volume flow rate of blood in the pulmonary artery? Give your answer in cm /s with two digits of precision. The viscosity of blood at 37°C is 2.1 x 103 Pa s. Your Answer: Answer

The pulmonary artery, which pumps blood from the heart to the lungs, has an inner radius of 18.8 mm and is 4.82 cm long. If the pressure drop between the heart and lungs is 1,275 Pa, what is the volume flow rate of blood in the pulmonary artery? Give your answer in cm /s with two digits of precision. The viscosity of blood at 37°C is 2.1 x 103 Pa s. Your Answer: Answer

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

What should be the surface tension of a liquid if its density, which is 1.44 g/cc, is the same as that of the calibrating liquid? The displacements of the liquid and the calibrating liquid inside the capillary tube are both 0.5 cm. The surface tension of the calibrating liquid is 29.4509 dynes/cm.
A well is 3500 meters deep and 3100 meters vertically deep. It is filled with two drilling fluids, the first with a density of 10.5 lb/gal located up to 1000 meters and the rest of the well is filled to the bottom with fluid with a density of 12 lb/gal. During the operation, a wellhead pressure equivalent to 320 psi was recorded. With these data in hand, the pressures occurred at the bottom of the well and the equivalent density of the bottom of the well in lb/gal are, respectively: The. 6389 psi/12.12 lbs/gal 6429 psi/ 12.1 lbs/gal 5959 psl/13.2 lbs/gal 6220 psi/11.9 lbs/gal E 20:13 + 130% =
Question 2: The pressure drop, AP, in a horizontal pipe depends on the pipe diameter, d, pipe length, L, pipe roughness, &, average velocity, V, density of the fluid, p, and absolute viscosity of the fluid, u. Express the variables in non-dimensional form using Buckhingham-Pi theorem (25 Points)
Question 2: The pressure drop, AP, in a horizontal pipe depends on the pipe diameter, d, pipe length, L, pipe roughness, ɛ, average velocity, V, density of the fluid, p, and absolute viscosity of the fluid, u. Express the variables in non-dimensional form using Buckhingham-Pi theorem
The kinematic viscosity of liquid oil is 20 stoke and relative density = 0.85. Find the dynamic viscosity of this liquid oil in Sl and British systems. (1 stoke = 1 cm/s, 1m 3.28 ft, 1ft 30.48 cm and 1kg = 2.2 lb). Choose the correct answer: a- In SI system 25 kg/m.s and in British system 16.6 Ib/ft.s b- In SI System 17 kg/m.s and in British system 1.17 Ib/ft.s c- In Sl system 20 kg/m.s and in British system 8.15 Ib/ft.s
A- Womersley number (a) of a human aorta is 20 and for the rabbit aorta is 17, the blood density is approximately the same across the species. The values of viscosity were 0.0035 Ns/m² for the human and 0.0040 Ns/m² for the rabbit. The diameter of the aorta is 2.0 cm for the man, and 0.7 cm for the rabbit, estimate the heart rate beats per minute (bpm) for both species
QI A ball made of INOX AISI 365 steel with density of 8.52 gricm3 was used to determine the viscosity of oil with specific gravity of 0.91. In the viscometer, the ball traveled 19 cm in 2.2 seconds. If the diameter of the ball is 2.95 mm, what is the viscosity of the oil in pa.s ? assume that water density is 1000 kg/m'.
The property of a fluid called viscosity is related to its internal friction and resistance to being deformed. The viscosity of water, for instance, is less than that of molasses and honey, just as the viscosity of light motor oil is less than that of grease. A unit used in mechanical engineering to describe viscosity is called the poise, named after the physiologist Jean Louis Poiseuille, who performed early experiments in fluid mechanics. The unit is defined by 1 poise = 0.1 (N s)/m2. Show that 1 poise is also equivalent to 1 g/(cm · s). %3D
In Figure below all fluids are at 20 deg.C. Determine pressure at point B, if pressure at point A is 150 kPa and weight of air is neglected. Use the table below for the densities at 20 deg.C. Liquid p. kg/m Kerosene - Ammonia 608 Benzene 881 Air Carbon tetrachloride 1590 Benzene Ethanol 789 Ethylene glycol Freon 12 B 1117 40 cm 9 cm 1327 20 cm Gasoline 680 14 cm Glycerin Kerosene 1260 t8 cm 804 Mercury- Water Mercury Methanol 13,550 791 SAE 10W oil 870 SAE 10W30 oil 876 SAE 30W oil 891 SAE 50W oil 902 Water 998 Seawater (30%e) 1025
23 ft^3 of air was drawn from a ventilation duct and measured by means of a dry gas meter. the meter's temperature averaged 60 F and the meter gage pressure was -1.9" H2O. Barometric pressure during the sampling was 752 mm Hg. Calculate the volume in standard cubic feet and in standard cubic meter (25C, atm)
Dynamic viscosity of fluid Density of fluid If X= , then the unit of X is = O m?/kg O m/sec? O m/sec O m?/sec The container contains an oil of specific gravity 0.64 with the pressure measured at the bottom of the container is 150 Pa. Find the pressure head in m of oil. The pressure head of oil in m = If the density of fluid is not a variable in a fluid flow, it is known as O Incompressible O Unsteady flow O Uniform flow O Compressible
1. A special-purpose piece of laboratory glassware, called a pyncnometer; is used to measureLiquid densities. It has a volume of 25 cc, and a mass of 17 .24 g when it is full of air. Whenfilled with a liquid of unknown density, its mass = 45.00 g. What is the density of this liquid?How large an error do we make if we ignore the mass of the air that was in it when we weighed itand found m = 17.24 g?