The points on the bullseye are measurements whose exact value is the center of the bullseye. Indicate the correct statement: (A). The points of target 3 have clearly less standard deviation than that of target 2. (B). Target 2 points have the worst repeatability of all. (C). The points of target 3 are a set of measurements that lead to a fairly accurate value of the variable, but the instrument cannot be considered very precise. (D). Target 4 points only have systematic errors.

The points on the bullseye are measurements whose exact value is the center of the bullseye. Indicate the correct statement: (A). The points of target 3 have clearly less standard deviation than that of target 2. (B). Target 2 points have the worst repeatability of all. (C). The points of target 3 are a set of measurements that lead to a fairly accurate value of the variable, but the instrument cannot be considered very precise. (D). Target 4 points only have systematic errors.

Principles of Instrumental Analysis

7th Edition

ISBN:9781305577213

Author:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Publisher:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

ChapterA1: Evaluation Of Analytical Data

Section: Chapter Questions

Problem A1.1QAP

See similar textbooks

Similar questions

The three targets from a rifle range shown below were producedby: (A) the instructor firing a newly acquired targetrifle; (B) the instructor firing his personal target rifle; and(C) a student who has fired his target rifle only a few times.(a) Comment on the accuracy and precision for each of thesethree sets of results. (b) For the A and C results in the future tolook like those in B, what needs to happen? [Section 1.6]
3) For the results, discuss the significance of the following in terms of accuracy or precision: a) Deviation vs Absolute Error. b) % Error vs Standard Deviation.
Consider the following sets of replicate measurements: (1) Calculate the mean and standard deviation of Group A. (2) Determine the confidence interval at 95% confidence level. Assume the data here are the only knowledge you have and no previous measurements are available.
I am supposed to calculate Average absolute deviation (%). I am not sure if 7.16 is the final answer, or do i need to multiply by 100 because they are asking for percent?
Scores from the midterm statistics exam followed a normal distribution with a mean of 68 and a standard deviation of 10. If a student had to score at least an 86 to earn an A, what is the probability that a student earned an A? (Use a table or technology. Round your answer to four decimal places.)
For a certain analysis, the concentration of the analyte was determined using the model equation: Sample - Sblank CA= k where CA is the analyte concentration, Seample is the signal given by the sample, Sblank is the signal given by the blank (sample with no analyte) and k is a proportionality constant. Which of the following formulas best describes the calculation for the combined uncertainty in CA? 2 usplank + ussample + (1) Splank CA Ssample CA = (2) 4sample) + (usmlank)´+ (ux)² CA 2 (uSsampte) +(uShlanz) + (+)° (3) CA Ssample-Spiank 2 uk (4) + (Usplane) + Ussample %3D blank CA
how do i know if my measurement is significantly different from the exact value, at least 2 sentences. exact value was 0.25 the average was 0.223 and standard deviation was 0.025. the RSD was 11.2%
Which of the following errors are determinate errors? Personal errors. Method errors. O Random errors.
3. A student weighed an unknown mass directly on an electronic balance of intermediate sensitivity, and got a result of 28.774 g. The student then realized a mistake had been made, and weighed the same unknown by difference on the same balance with the following results:Mass of beaker plus unknown = 59.121 g.Mass of empty beaker = 30.346 g.When the sensitivity of the balance is taken into account, the two values obtained for the unknown mass are considered to be:a. Differentb. The SameExplain your answer.
Assuming that you weighted a piece of silver five times and each time you got 52 grams. However, the actual weight from the Bureau of Standards said it should weigh 50 g. (a) What is the % relative errors? (b) What type of error does this exemplify? (c) Does this affect (a) reliability (b) Accuracy (c) both a & b
There samples of the same metal are weighed and their masses are found to be 42.02 g.4.63 g, and 44.16g. The corresponding volumes are 455 ml., 5.11 ml., and 4.84 m., respectively. Determine the density, d, of the metal and calculate the standard deviation of the density. d= The densities of several metals are given in the table. Metal (g/cm) aluminum 2.70 iron 7.87 cobalt 8.90 copper 8.96 gold 19.3 glemt Which of the metals could the sample be? gold cobalt D aluminoun copper g/cm³
Chemistry find absolute and relative standard deviation of this data.