The plate of thickness, t 5 mm, is loaded with the following stress; oy = 100 MPa, o, = -60 MPa, E = 200 GPa, v = 0.33. If a = 160 mm, and b = 200 mm, C A Calculate the change in the length (mm) of AD. Select the correct response

The plate of thickness, t 5 mm, is loaded with the following stress; oy = 100 MPa, o, = -60 MPa, E = 200 GPa, v = 0.33. If a = 160 mm, and b = 200 mm, C A Calculate the change in the length (mm) of AD. Select the correct response

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The rigid bar AB is hinged at A and supported by a steel plate hanger. The hanger is fixed at C and bolted at D with two plates. D Given: Width of plate hanger = 40 mm Thickness od plate hanger = 10 mm Bolt diameter = 20 mm 2 m 1.2 m B Allowable bolt shear stress = 60 MPa Allowable bolt bearing stress = 250 MPa W a. What is the allowable stress in the hanger based on bolt capacity in double shear at D. b. If the maximum tensile stress in the hanger is 130MPA, find the allowable load W c. If the load W= 60KN, find the vertical displacement at B.
2. A rod is composed of an aluminum section rigidly attached between steel and bronze sections as shown in the figure. Axial loads are applied at the positions indicated. The cross-sectional area of the rod is 300sq.mm. Express your answer in MPa. Determine the stress in the steel. b. a. Determine the stress in the aluminum. Determine the stress in the bronze. C. STEEL ALUMINUM BRONZE 56kN 14kN -0.6m- -0.9m- -0.76m-
SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and attached to two vertical rods. Assume that the rods were initially stress-free. Allowable stress in steel is 120 MPa and in bronze is 60 MPa. For this problem, a = 1.8m; b = 1.3m; c = 1.7m. b C P Steel: A=900 mm² E = 200 GPa L=1.5m Bronze: A 1200 mm E=83 GPa L=2.0m What is the value of P without exceeding the allowable stress of bronze, in kN? 174 145 161 124
A thin polymer plate PQR is deformed so that corner Q is displaced downward 0.9 mm to new position Q', as shown in. Determine the shear strain at Q' associated with the two edges (PQ and QR). Assume a = 150 mm, b = 216 mm, c = 180 mm, and A = 0.9 mm. a b P R C Answer: Shear strain y = Q i A X urad.
G6//The light rigid bar ABCD shown in Figure is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free, determine the stress in each rod after the load after the loadP = 20 KN is applied. Steel L=2m A=250mm 4m E=200Mpa C. Aluminum L=2m A=500mm2 2m 2m E-72Mра P=20KN
Part 2 * Your answer is incorrect. The z-component of momemt M will cause compression at A and B, and tension at C and D. The y-component of moment M will cause compression at A and D, and tension at B and C. The maximum tensile bending stress will occur at point C. Calculate the magnitude of the largest bending moment that can be applied so that the stress at corner C does not exceed 205 MPa. Answer: M- eTextbook and Media Save for Later Part 3 8.31E1 Answer: M-i The z-component of moment M will cause compression at A and B, and tension at C and D. The y-component of moment M will cause compression at A and D, and tension at B and C. The maximum compressive bending stress will occur at point A. Calculate the magnitude of the largest bending moment that can be applied so that the stress at corner A does not exceed 205 MPa. eTextbook and Media Save for Later Part 4 kN-m * Your answer is incorrect. kN-m Submit Answer Determine the maximum bending moment that can be applied to this cross…
SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and attached to two vertical rods. Assume that the rods were initially stress-free. Allowable stress in steel is 120 MPa and in bronze is 60 MPa. For this problem, a = 1.8m; b = 1.3m; c = 1.7m. a b C Steel: A-900 mm E = 200 GPa L=1.5m Bronze: A 1200 mm E=83 GPa L=2.0m What is the ratio of the elongation of steel to bronze? 0.367 0.433 0.467 0.333
Determine the normal stress in the steel plate. Gusset plate is 16 mm thick column pin diameter = 20 mm gusset plate steel plate 70 kN pin 60mm 8-mm plate thickness 183.45 MP 0148.53 MPa 58.33 MP3 22282 MP A 14583MP
Two steel tubes are joined at B by four pins (dp = 11 mm), as shown in the cross section a – a in the figure. The outer diameters of the tubes are dAB = 40 mm and dBC = 28 mm. The wall thicknesses are tAB = 6 mm and tBC = 7 mm. The yield stress in tension for the steel is (y = 200 MPa and the ultimate stress in tension is (U = 340 MPa. The corresponding yield and ultimate values in shear of the pine are 80 MPa and 140 MPa, respectively. Finally, the yield and ultimate values in bearing between the pins and the tubes are 260 MPa and 450 MPa, respectively. Assume that the factors of safety with respect to yield stress and ultimate stress are 4 and 5, respectively.Calculate the allowable tensile force Pallow considering tension in the tubes.Recompute the Pallow for shear in the pins.Finally, recompute Pallow for bearing between the pins and the tubes. What is the controlling value of P?
Problem 1: The steel rod is placed inside the copper tube, the length of each being ex-, actly 15 in. If the assembly is compressed by 0.0075 in., determine the stress in each component and the applied force P. The moduli of elasticity are 29 × 106 psi for steel and 17 x 10° psi for copper. 0.6 in. 0,75 in. Problem 2: A steel hoop, 10 mm thick and 80 mm wide, with inside diameter 1500.0 mm, 15 in. is heated and shrunk onto a steel cylinder 1500.5 mm in diameter. What is the nor- mal force in the hoop after it has cooleď? Neglect the deformation of the cylinder, and use E == 200 GPa for steel. 0.125 in. Problem 3: The timber member has a cross-sectional area of 1750 mm² and its modulus of elasticity is 12 GPa. Compute the change in the total length of the member after the loads shown are applied. 40 kN 35 kN 20 kN D +1.5 m -3 m 3 m
2. The bronze bar 3 m long with a cross-sectional area of 350mm2 is placed between two rigid walls. At a temperature of -20 oC, there is a gap of 2.2 mm. Find the temperature atwhich the compressive stress in the bar will be 30 MPa ifthe bar will experience:a. No tensile.b. With an tensile of 5,000 N.Use α = 18.0 x 10-6 /oC and E = 80 GPa.
A steel rectangular block is subjected to a uniform stress of o = 150 MPa acting on all faces. The dimensions of the block are as follows: L_x=100 mm,L_y=30 mm,L_z=40 mm. Determine the change in length along the y-axis. Use E = 200 GPa and v 0.3. Note that ɛ_0=-o/E(1+2v). A -0.03 mm -0.015 mm -0.009 mm -0.012 mm