The pipe assembly shown is subjected to a force F= 600 N. The pipe has an inner diameter of 20 mm and an outer diameter of 30 mm. It is made of steel with Sy 250 MPa. Determine the safety factor at point A using the maximum shear stress theory.

The pipe assembly shown is subjected to a force F= 600 N. The pipe has an inner diameter of 20 mm and an outer diameter of 30 mm. It is made of steel with Sy 250 MPa. Determine the safety factor at point A using the maximum shear stress theory.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The horizontal shaft with a diameter of d-41 mm is supported by a thrust collar that rests on a 31-mm-thick plate. The thrust collar is 24-mm thick. The thrust collar has an outer diameter of Dcollar - 64 mm. Determine the load P that causes an average shear stress of 89 MPa on the cylindrical surface of contact between the shaft and the thrust collar Thrust collar area P Thrust collar Plate d Dcollar
In the following structure if the temperature increases by 20 °C, determine the normal stress in Links (1) and (2). E (GPa) A (mm2) a (1/°C) 11.9x10-6 Link 1 200 310 Link 2 70 620 22.5x106 500mm 350mm B to A 100mm 300mm (2) 6kN 400mm
View Policies Current Attempt in Progress Aspherical rubber balloon is blown up until its diameter is three times the initial diameter. If E = 10750 psi and v = 0.47, determine the stresses in the balloon. Assume the stress-strain behavior is linear. Answer: o = i ksi
The gas storage tank is fabricated by bolting together two half cylindrical thin shells and two hemispherical shells as shown. If the tank wall has a thickness of 50 mm for cylindrical and hemispherical shells, The bolts were installed as 40 bolts/meter. The tank and the 25 mm diameter bolts are made from material having an allowable normal stress of 150 MPa and 250 MPa, respectively. The tank has an inner diameter of 4 m. What is the maximum pressure that tank can contain.
Question: Determine the average shear stress in the single pin A and double pin B as well as the average normal stress in member AD if member BA is subjected to load of 500N/m. Pin A and pin B have diameters of 20mm and 10mm respectively while member AD has a square cross section of 30 mm on each side. D 3000 mm 500 N/m B A 2000 mm 2000 mm
The pressure vessel has a thickness 2 cm, diameter 20 cm. Calculate the internal pressure longitudinally and laterally. If the longitudinal stress is limited to 150 MPa and the circumferential stress is limited to 100 MPa. Which one will be used for safety? *
A machinery uses a helical tension spring with wire diameter of 3 mm and coil outside diameter of 35 mm. The spring has 9 total coils. The design shear stress is 500 MPa and the modulus of rigidity is 82 GPa. Determine the force that causes the body of the spring to its shear stress in N. Consider ground ends.
The thin-walled pipe has an inner diameter of 0.5 in. and a thickness of 0.025 in. If it is subjected to an internal pressure of 500 psi and the axial tension and torsional loadings shown, determine the principal stress at a point on the surface of the pipe.
The d = 17-mm-diameter solid rod passes through a D = 22-mm-diameter hole in the support plate. When a load P is applied to the rod, the rod head rests on the support plate. The support plate has a thickness of b = 12 mm. The rod head has a diameter of a = 34 mm, and the head has a thickness of t = 9 mm. The shear stress in the rod head cannot exceed 125 MPa, the punching shear stress in the support plate cannot exceed 80 MPa, and the bearing stress between the rod head and the support plate cannot exceed 120 MPa. Determine the maximum value of Pmax that can be supported by the structure.
The assembly consists of a bronze tube fitted over a threaded steel bolt. The nut on the bolt is turned until it is finger-tight. Determine the stresses in the sleeve and bolt when the temperature of the assembly is increased by 200°F. Use the following data: Bronze Steel A (in. ²) 1.5 0.75 a (/°F) 10 × 10-6 6.5 x 10-6 Bronze tube 40 in. E (psi) 12 × 106 29 × 106 STA UT TEO
The steel pipe of length L = 541 mm is filled with concrete and subjected to a compressive force P = 91 kN. What is the average normal stress in the concrete due to this loading? The pipe has an outer diameter of 80 mm and an inner diameter of 70 mm. The modulus of elasticity is Est = 200 GPa for steel, and E. = 24 GPa for concrete.
A 60˚ strain rosette measures the following strain at a point on the aluminum skin ofan airplane. ϵ0 = 160 ×10-6 m/m, ϵ60 = -220 ×10-6 m/m and ϵ120 = 360 ×10-6 m/m. Using E = 10 ×106 psi and v = 0.3, Determine the principle stresses and the maximum in-plane shear stress.