The output signal given above is taken from a circuit with the frequency of the input signal 100 Hz, the capacity of the capacitor used is 4µF, and the value of the ripple factor is 1.21. Answer the following questions using the ones given. The diodes used are silicon diodes, their operating voltages are 0.7 volts, and can be omitted because their resistance is very small. a) draw a graph showing how the output voltage would have been if the capacitor had not been used in this circuit

The output signal given above is taken from a circuit with the frequency of the input signal 100 Hz, the capacity of the capacitor used is 4µF, and the value of the ripple factor is 1.21. Answer the following questions using the ones given. The diodes used are silicon diodes, their operating voltages are 0.7 volts, and can be omitted because their resistance is very small. a) draw a graph showing how the output voltage would have been if the capacitor had not been used in this circuit

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
What is the difference between a diode and rectifier?
Determine the current I in the circuit (i). Assume the diodes to be of silicon and forward resistance of diodes to be zero.
True or False. Please explain. thank you As the temperature increases, the forward voltage decreases in a silicon diode. Then, the graph of the forward bias region will shift to the left.
In a full wave rectifier circuit involving double diodes, a sinusoidal input signal of the following nature is applied e=10 sin(500*pi*t) V. What will be value of the dc voltage obtained at the output of the rectifier.
For the circuit shown below, compute the maximum current through each resistor when terminal A is a) positive and, b) negative. Assume the diodes are ideal.
Consider the following circuit diagram. Using practical diode model solve the following items. i. What is the type of rectification in this circuit? ii. Calculate the total peak secondary voltage (Note that “RMS" value is given in the circuit) iii. Sketch the plot of time vs voltage over Load (RL) iv. Find the average voltage over Load. v. Find the maximum current passing over diodes. vi. Find the peak inverse voltage (PIV) over the diodes. vii. Find the minimum fuse current rating for the primary coil. 5:1 D DA 120 V rms D3 D2 RL=10kQ RL out ell lelll
For the diodes used , at what Voltage (VD) does condection stars .
Q1 Figure Q1(a) is a full wave bridge circuit with a capacitor filter and the output waveform produced by the circuit is shown in Figure Q1(b). Assume all the diodes in the circuit have a forward voltage of 0.7 V. (a) (b) Sketch the waveform in A, B, C and D as shown in Figure Q1(a). Design the circuit by finding the value for the capacitor, C and the line voltage Vpri(rms) to the circuit to produce the output as shown in Figure Q1(b).
Given the clamper circuit below, assume that the value of R and C are large enough sothe voltage across the capacitor does not change significantly during the interval of time.a. Using the simplified diode model, simulate the action of the circuit when the Silicon diode isin forward and reverse bias condition and measure the corresponding output voltage.b. Draw the complete output waveform of the circuit
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as germanium and D2 as silicon diodes. Input Vpp%3D20V, V1=3 V and V2=10 V. R D2 D1 Vin Vout V1 V2 Maximum voltage of output waveform Minimum voltage of output waveform Ps
Find the value of RI in the circuit shown below, assume Ipz is twice Ipi. The diodes have constant voltage drop of 0.7v for silicone and 0.3v for germanium