4. The output response of a temperature measuring system of a kiln in a Cement Plant is represented by Y(t) =4-4e-3t when it is subjected to a step input of magnitude 4. If an impulse input of value 3 is given to the system find the response function of the process?

Q: 4. Consider the tank illustrated below where the density if the fluid is p. The resistances R₁ and…

A: According to question we have figure Where ρ-density qmi-inflow rate R1 and R2-Linear resistance…

Q: Draw a graph of the cumulative cash position that shows the effect of cash flow over time for an…

A: The cash flow over time affects the industrial growth in both positive and negative ways. When the…

Q: Q4/I Answer two of the following: AI Derive an expression for the degree of reaction for axial…

A:

Q: Y(s) A first order system: G(s) = X(s) Given: - is given 0.5s+1 Required: Find: a. Time constant and…

A:

Q: Determine values for A and R from the step response

A:

Q: Energy transfer in mechanical systems 70 KW of input power through the input shaft and delivers…

A:

Q: In a non-interacting system consisting of two interconnected tanks, the liquid levels in the first…

A: Since you have posted a question with multiple sub-parts, we will provide the solution only to the…

Q: 3- A mixed tank heater of time constant t = 6 min.. Derive a transfer function relating the tank…

A: Mixed tank is a tank in which the properties of interest like temperature concentration of liquid,…

Q: If a hot water reheat coil is installed with a three-way modulating valve? A. The van box can only…

A: The correct option has to be chosen.

Q: A horizontal cylindrical tank shown in Fig.a is used to slow the propagation of liquid flow surges…

A:

Q: Obtain a model of a level tank of uniform cross section of area A, to which a flow resistance, such…

A:

Q: Response of a Ist order system to an impulse input is also a/an a. Impulse function b. Sinusoidal…

A: The correct option for the response of a 1st order system to an impulse input is to be chosen.

Q: Q1: A slab of high thermal conductivity at temperature T, at zero time receivers on one side a heat…

A: Heat is transferred to a solid slab through conduction at one side and other side is exposed to air.

Q: Determine the value of Kc in Figure Q2(b) for a regulator case in which the closed-loop response has…

A:

Q: A. What is cavitation? Where does it occur in centrifugal pumps?

A: Since you have posted multiple independent questions in the same request, we will solve the first…

Q: Continuity equation is

A: To choose  the option that correctly describes continuity equation

Q: Which of the following functions is not physically realizable?

A: we have to findout the function which is not physically realizable

Q: A surge tank in Fig. is designed with a slotted weirso that the outflow rate w is related to the…

A:

Q: gas above the liquid as shown below. Derive an ODE relating the liquid level h to the input flow…

A:

Q: A pressure difference of 2.40 x 10 Pa is used to inject a sample onto a 64.2 cm long capillary that…

A: It is given that,pressure difference, ,length of capillary, ,diameter, viscosity of the sample,

Q: Q/ Three chemical engineers (Mohammed, Ahmed and Ali) discussed about the effect of the pressure…

A: We are asked to find the answer for the efficicency of the Rankine cycle with the pressure of the…

Q: For the sinusoidal input of a zero order unit gain system the ratio of output and input amplitude is…

A: For a sinusoidal input with gain k, the input is k  sinθ. Since the system is zero order, output is…

Q: The response of a derivative time to a step input is: a. Sinusoidal O b. Step O c. Ramp O d. Impulse

A: Controllers are used in a Feedback system.The four types of controller used in the Chemical industry…

Q: The cross-section of the fuel tank of an experimental vehicle is shown in the figure below. The…

A: Given :The specific gravity of the fuel, Length of the vent,

Q: Q4: For the signal flow graph of a certain control system shown below, find the system…

A: Step 1:Step 2:

Q: a. A Waste Water (WW) tank initially containing 8 kgs of organic salt in 80 lit of water is being…

A:

Q: (1) Find out the transfer function between input U and output Y as shown in Figure 1 and write the…

A: ouputinput = Y(s)U(s)  = K1τ1s + 1 *K2τ2s + 11 + K1τ1s + 1 *K2τ2s + 1 ouputinput = Y(s)U(s)  = K1τ1s…

Q: A first order system with transfer function G₂ = Y(S)/X(s) = 1 /(s+1) is subjected to input X(t) =…

A:

Q: P.15.7 Water is pumped at a rate of 200 gpm through a control valve which has a pressure drop of 30…

A: To solve above problem, we will use the equation for the pressure drop across a control valve :ΔP is…

Q: A copper sphere initially at a uniform temperature To is immersed in a fluid. Electric heaters are…

A:

Q: Rfor the liquid-level system of figure below. q(s) Q4. Derive the transfer function The…

A:

Q: The output response of a temp measuring system of Kiln in a cement plant is respresented by y ( t )…

A: Given information: Output response of a step input of magnitude 9 is y(t) =6-6e^-6t Find the…

Q: In a tank heater with agitator, the tank outlet temperature (T) and the heater connected to the tank…

A: