The orsat analysis of the excesses gases from a diesel engine using hydrocarbon fuel is given CO, 8.2%; 0 9.8%; CO 0.85%. Calculate (1) Fuel air ratio (2) mass analysis of fuel.

Q: Determine the Resultanto f the eoplanar orcesestem

A:

Q: where did 144 come from

A:

Q: Based on the system shown in Figure 1, develop the position equations from your fixed datum lines,…

A:

Q: resolve solution

A:

Q: S0ON so

A:

Q: Figure 3 shows one cart with a mass that is separated from two walls by two springs and a dashpot,…

A:

Q: Below are incomplete views of the parts or figures. Complete them by drawing the lines of…

A: Given:Find:Draw the lines corresponding between the views.

Q: Finding the y centriod.

A: Given data, the I section is given with dimensionFind outthe centroid along the y-axis

Q: 10 kNim 50 kN Identify the moment diagram of the beam shown. 3125 3125 (AN mA 022 (AN-m)A

A:

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: 3. both wires is identical at 1.5 meters and both wires are 5 mm in diameter. The steel wire is made…

A:

Q: 1. What is the type of robot?

A: ***As per our company policy we are supposed to do only 1 question if you need the rest please…

Q: Identify the following sectioning views (a, b, and c). a O Removed, Revolved and Removed O All…

A:

Q: can you answer 1B

A:

Q: Draw the box closing mechanism given in the figure in the given dimensions. Determine the velocities…

A:

Q: what is 1.54 from?

A: Given:The length of CD is .The length of BC is .The length of AG is The length of AD is .Consider…

Q: -150 mm 15 mm B C 150 mm -15 mm 15 mm - 100 mm·

A: given;

Q: A plane's propeller can be modeled as a thin, uniform rod that rotates about its frictionless center…

A: Given data  F = 591 N  L = 6.51  m  mass of propeller (m) = 10.1 kg    To determine  (a) direction…

Q: You are designing a new engine; this device operates with liquid fuel as an input and gener energy…

A: Hello. Since you have posted multiple questions we will solve the first question for you. If you…

Q: □ 18 F.V.

A: According to the details provided in the question, we need to draw three projection views.

Q: Tät-/e205+(17-78 2.

A: Given Data⇒a↦=202+17.782

Q: what is part number 4

A: Solution:

Q: Add the length of all the horizontal pieces. They go left and right.

A:

Q: how can I get the 85 α

A:

Q: As shown, a section of a roller coaster track (Eigure 3) follows the form of y = (2/3)x¹.5 Locate…

A:

Q: What is the average force magnitude?

A:

Q: ********** QI/A/ The 4-mm diameter cable BC shown in Figure Q1-4 is made of a steel with E-200 GPa…

A:

Q: A multi-stage pump, 260 gpm capacity is installed in a well 27 ft below the static water level.…

A: Given data:  The capacity of the pump is given as Q = 260 gpm = 0.579 ft3/sThe total discharge head…

Q: In this case, the applied force is always pulls upward, but the amount of force that can be applied…

A: According to the given data  We need to find The true statement

Q: (12m) ladder weighs 200N and is ed against a smooth vertical wall its lower and (6m) from the wall

A:

Q: number d and e?

A: To solve this question, we will use the moment equilibrium equation which is mentioned in the…

Q: A differential element on the bracket as shown in Figure Q1 is subjected to plane strain that has…

A:

Q: Figure 1 of 1 30 40 F2

A: Given, F1 = 210 N F2 = 510 N Angle between two forces = θ = 40°

Q: The 45° strain rosette is mounted on a surface of the bracket as shown in Figure Q1. The bracket is…

A: Esteel=120 GPaμ=.28 εa=100+60×10-6 εb=-200×10-6εc=-180×10-6 θa=0° ,θb=45°,θc=90°

Q: At a given moment four link mechanism OABO, is in the position shown on the figure and OA= AB = AO =…

A:

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.