Figure 1 of 1 30 40 F2

Q: A motor operates at 1800 RPM and expends 2 HP.  How many ft-lbs of torque does it provide at that…

A: Given data: The speed of the motor is; N=1800 RPM. The power of the motor is; P=2 HP.

Q: 00 0 021 0 043 0 25 0 1280

A:

Q: Successive approximation ADC explian

A:

Q: 8. Write the name of each component (1-19) in the figure selow.

A:

Q: TS DIAGRAM

A:

Q: Which percentile is typically for designing lower-limit dimensions? - 95th 5th 50th 99th

A:

Q: D Question 2 Express the force TBC as a vector (in terms of i, j, k). Show all calculations on your…

A: Express the force TBC as a vector (in terms of i, j, k). Show all calculations on your paper and…

Q: Q4 The L2 steel bolt as shown in Figure Q4 has a diameter of 5 mm, and the link AB which is made…

A:

Q: 400N 200 Z00 N さ

A: Given Data :

Q: Determine both magnitude of OA and Oy on the figure below? F=10-06 -A 30 45°

A:

Q: 400 300 stn 60

A: 400sinθ=500sin60=5003/2=10001.732=578.03

Q: 0.2 m B 0.2 m 1.3 m 0.7 m A P Circular

A:

Q: y F1 = 30 N 3 4 F3 = 50 N 20° F2 = 20 N

A: From the data given in question, F1 = 30 N F2 = 20 N F3 = 50 N

Q: 2 ft 2 ft 3 ft A 6 ft

A:

Q: 1-23.Determine the length of side C of the triangle shown in Figure P1-23.

A:

Q: 35 86 $ 38 51 20 R10 105 16 F

A: Given 3D model To find Orthographic view

Q: PROBLEM. A mechanism carries a constant load P applied to the seat as given. As CDFE and EFGH is a…

A: Force in pin H and member FG

Q: F Find the y-component of F2 in Newtons. If the calculated answer is not whole number, express it in…

A:

Q: 2. For the plan area shown, determine the location of the Centriod. Use you're the last two digits…

A:

Q: FIGURE 1 60 kN B 0.75 E F :1.00 1.00. 1.00 25 kN

A:

Q: F3 = 750 N 45° 5 30° F2 = 625 N F = 850 N

A:

Q: RIS R12 frant sew R32

A: Given 3D model To find Three views

Q: E 12.5 m C А 8 m 5 m

A:

Q: FA -X B FB Alpha = 34 degrees

A:

Q: 1st image : What is the reading on the micrometer? 2nd image : What is the reading on the…

A:

Q: Consider (Figure 1). Figure 0.3 m. 120° 45° 60⁰° 325m Y Part A Determine the magnitude of the…

A: Given data: Force (F)=260 N To find:-the magnitude of the moment of the 260-N force about the x…

Q: 150 m 50 mm 85 mm Section X-X 20 kN

A:

Q: 1-8. Determine angles a, b, and c (Figure P1-8). a 35° FIGURE P1-8

A:

Q: Determine the magnitude of F so that the resultant couple moment is 11.5 kN -m , counterclockwise.…

A:

Q: Find Rab for the circuit fn figure. 202 202 Rab 792 252

A: The circuit is shown below.

Q: Circle the letter corresponding to the view on the right that shows the result of rotating the…

A: (1) Find Rotate the object (1) about the z-axis and then about the x-axis.

Q: C O C

A: Given: Hatching: Differentiates the areas that are cut and those areas that are not cut by the…

Q: 50 mm 150 mm 50 mm 85 mm Section X-X 20 kN

A: Let us shift the load to section X-X. The moment M and force P will create the same effect.

Q: Use blank or isometric grid paper to draw the isometric views of the following objects.

A: Draw the given three views.

Atomic diffusion in solids

In material science, diffusion can take place in solid, liquid, and gases. In solids, atomic diffusion can take place with the help of thermally activated and randomly vibrating atoms. The atomic diffusion in solids is complex and very slow in comparison to atomic diffusion in liquids and gases because the interatomic distance between the atoms is smaller in solids as compared to liquids and gases.