The one-line diagram of a power system is shown below. Line impedances are shown on the one-linediagram. The generators, transformers and the load are rated as follows:: 100VA, 20 kV, X = 0.09 pu: 40 MVA, 18 kV, X = 0.09 puTransformer 1 (T1) : 100 MVA, 204/200Y kV, X = 0.16 puTransformer 2 (T2): 60 MVA, 200Y/20A kV, X = 0.2 puLoad: S = 100 MW+j 50 MVar, at 200 kVGenerator 1 (G1)Generator 2 (G2)Draw the impedance diagram and indicate all impedances in per unit. Choose a base of 100 MVA,20 kV in Generator 1 (G1) side.T1G1ΔΥj30 Ωj60 Ωj30 ΩLoadT2ΥΔG2

Base MVA=100 MVA,Base voltage Vb=20 kv,Asked to draw the impedance diagram?

The one-line diagram of a power system is shown below. Line impedances are shown on the one-line diagram. The generators, transformers and the load are rated as follows: Generator 1 (G1) Generator 2 (G2) Transformer 1 (T1) Transformer 2 (T2) Load Draw the impedance diagram and indicate all impedances in per unit. Choose a base of 100 MVA, 20 kV in Generator 1 (G1) side. T1 G1 : 100 VA, 20 kV, X = 0.09 pu : 40 MVA, 18 kV, X = 0.09 pu : 100 MVA, 204/200Y kV, X = 0.16 pu : 60 MVA, 200Y/20A kV, X = 0.2 pu : S = 100 MW+j 50 MVar, at 200 kV ΔΥ j30 Ω j60 Ω j30 Ω Load T2 ΥΔ G2

The one-line diagram of a power system is shown below. Line impedances are shown on the one-line diagram. The generators, transformers and the load are rated as follows: Generator 1 (G1) Generator 2 (G2) Transformer 1 (T1) Transformer 2 (T2) Load Draw the impedance diagram and indicate all impedances in per unit. Choose a base of 100 MVA, 20 kV in Generator 1 (G1) side. T1 G1 : 100 VA, 20 kV, X = 0.09 pu : 40 MVA, 18 kV, X = 0.09 pu : 100 MVA, 204/200Y kV, X = 0.16 pu : 60 MVA, 200Y/20A kV, X = 0.2 pu : S = 100 MW+j 50 MVar, at 200 kV ΔΥ j30 Ω j60 Ω j30 Ω Load T2 ΥΔ G2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The 240 kV transmission line is intended to be connected to a 220 kV transmission system through an autotransformer. The single-phase transformer that is available to make the connection is 120 MVA and 240kV/20kV Draw the connection of this autotransformer and show on the same diagram: The magnitude of the input and output voltages of the autotransformer (Magnitude and polarity)Currents and in the windings (magnitude and direction)The voltages in the windings (magnitude and polarity)The input and output currents of the autotransformer (magnitude and direction)Calculate the power capacity of this autotransformer
Q22) Consider a 3-phase, 33 kV transformers with N1:N2 = 900:150. Calculate the secondary line voltage on no load condition the windings are connected in the following configurations i) Star-Delta. ii) Delta-Delta.
3.8. Three identical 9-MVA, 7.2-kV/4.16-kV, single-phase transformers are con- nected in wye on the high-voltage side and delta on the low voltage side. The equivalent series impedance of each transformer referred to the high-voltage side is 0.12 + j0.82 S per phase. The transformer supplies a balanced three- phase load of 18 MVA, 0.8 power factor lagging at 4.16 kV. Determine the line-to-line voltage at the high-voltage terminals of the transformer.
1. A single-phase power system as shown in Figure 1 consists of a 240 V, 60 Hz generator supplying a load, Zod = 8 + j6 Q through a transmission line of impedance, Zne = 0.08 + j0.14 Q. Answer the following questions: (1) transformer, T; and T2. Determine the voltage at the load and transmission line losses without the (ii) Determine the voltage at the load and transmission line losses with the transformer, T, and T2. T1 T2 1:10 10:1 IG Zaine Zioad source Figure 1
2) The power system consists of generators, motors, transformers, and transmission lines. The ratings are as follows: G1: 3-phase generator 25 MVA, 11 KV, X = 20% M1: 3-phase motor M2: 3-phase motor T1:3 single phase transformers T2: 3-phase transformer Line: 15 MVA, 13 KV, X = 25% 7.5 MVA, 13 KV, X = 25% Single phase transformer rating 30 MVA, 6.9/69 KV X = 10% Three phase transformer rating 30 MVA, 13.8/69 KV X = 10% Χ - 50 Ω = Τι G₁ 2. Line Figure 1. 3 T2 Σ M₁ Δι M2 Find the reactance (X) in p.u. units, given the base value of 25 MVA, 11 KV.
There is a three-phase system such that the phase current in the generator, lines and charging phase is the same. The phase voltage in the generator must be 1000 [V] with clockwise sequence. The connected load must be such that the phase current in each load is 10 [A] and its power factor is 0.97 “lagging”. a) Determine phase currents in the generator, lines and phase in the load
Figure below shows a power system. The rating of generators and transformers are:G1:25MVA, 6.6KV, jO.2 p.u. G2:15MVA, 6.6KV, jo.15 p.u. G3:30MVA, 13.2KV, jo.15 p.u. T1: 30MVA, 6.6A- 115Y KV, jo.1 p.u.T2: 15MVA, 6.6A- 115Y KV, jo.1 p.u. T3:single phase units each rated 10MVA, 69/ 6.9 KV, jo.1 p.u. Find te reactances in p.u, take a base of 30MVA, 6.6 KV in the circuit of G1 .=.XG1 G2} 4 A lubu T2 T1 T3 G1 G3 j120 2 j90 N
Consider a 3-phase, 35 kV transformers with N1:N2 = 150:900. Calculate the secondary line voltage on no load if the windings are connected in i) Delta-Star [ ii) Star-Delta
It is bartleybe's policy that if questions objective than you need to solve at least first 3 questions.