The offset distance of a simple curve from the PT to the tangent line passing through PC is equal to 131m. The simple curve has a degree of 3 degrees. Evaluate the length of chord. Calculate the tangent. Calculate the stationing at PT given that Station PI is at 13400 m.

Q: Which of the following shapes are generally considered when the area is ?computed by map…

A:

Q: 5.1 The recommended scales for use on technical drawings are specified in the following table.…

A: To find: Choose the suitable code for the given scales for use on technical drawings.

Q: Compare and contrast the uses of T-square and setsquares.

A: T-square: It is a technical instrument that is used for drawing purposes.  It is mainly used by…

Q: How many "varas" are there in a single ruler measurement?

A: A single ruler is the standard ruler which has measurements given in inches or mm. It is used to…

Q: Meaning of scale in measurement

A: scale is used to show the actual dimensions that exist in a drawing sheet. you can clearly…

Q: how did you get 1.5 for the first part

A: In the original question it is stated that Vmax=2 Vmin In the solution, the following is given.…

Q: The shape factor for the uniform section shown below is 20 Î 20 + 50 50 * 50 50

A:

Q: Only Draw profile with appropriate scale

A: To draw the profile to the given levelling

Q: 10 divisions of vernier scale are equal to 11 divisions of a main scale of each 0.1 mm. What is the…

A: Given data- 10 divisions of vernier scale=11 divisions of main scalemain scale one division=0.1 mmTo…

Q: ETERMINE THE LOCATION OF CENTROIDAL X AND Y. NOTE: UNITS ARE IN INCHES.

A:

Q: express each measurement in feet.42 inches

A: Given: The measurement is 42 in.

Q: what is the difference between 42 square meter and 42 meter square

A: It is needed to differenciate between 42 square meter and 42 meter square.

Q: A line was measured as 79.52 Chains. What is the length of the line in feet? (to nearest 0.1 foot)

A: 1 chain = 66 feet 79.52 chains = 79.52 x 66                         = 5248.3 feet

Q: Calculate the dimension marked in red X in the following figure

A: for the given structure shown  22×26  unit2 - dimensions of the upper block40 unit - length of the…

Q: determine the centroid of the area shown with respect to the given x-axis

A:

Q: but I nee

A: Draw the figure Consider a differential element of size dy

Q: R10 30 50 O. 15 R30

A:

Q: From the diagram shown, all dimensions are in millimeters. Find the length of side x. 89 00' 2,268…

A:

Q: Which of the following shapes are generally considered when the area is ?computed by map…

A: Given: shape of map To determine:  Which shape generally considered  for area calculation.

Q: What type of meridian does the figure represent? W- S Meridian O True Meridian O Assumed Meridian…

A: To determine which of the following meridian is show in the figure.

Q: H MM 0 10 20 30 40 50 60 70 80 90 100 DIMENSION THE PART USING METRIC DIMENSIONS. USE DIVIDERS OR…

A: The front view and top view of an object is shown in the above figures. Also scale of dimensions…

Q: express each measurement in feet.50 inches

A: Given: The measurement is 50 in.

Q: Express all denominate numbers 8 gal 3 qt  35 qtin the same unit.

A: Solution:-

Q: Find

A:

Q: The coordinates of centroid for the following section is 150 mm - 20 mm 20 mm 20 mm 300 mm 500 mm

A:

Q: Part A What is the ratio scale for the equivalent scale of 1 in. = 80 ft? Express your answer using…

A: 1 ft =12 inch given 80 ft =12*80=960in Ratio scale=112×80=1:960

Q: Define matrix's diagonal, off-diagonal, subdiagonal, and superdiagonal elements. Illustrate each.

A: An n×n matrix, or a matrix with the same number of columns as rows, is known as a square matrix.

Q: can you explain how to do this in cad. using the details below. Can you like specify the dimensions…

A: Given data,

Q: Define Relative Density.

A: Relative density or specific gravity:

Q: express each measurement in feet.108 inches

A:

Q: 112 тm К30 тm ->- 30 тm -+30 тm ->-30 mт -> Рart a) Determine the moment of inertia of the shaded…

A:

Q: Draw the figure to an enlarged scale in Isohyetal method

A: The iisohyetal approach is a technique for calculating the average amount of precipitation within a…

Q: State of S and T during Spanish colonization

A: Brief concept- Spanish colonization- The arrival of Miguel López de Legazpi's expedition from Mexico…

Q: In the figure below, find the SAB 0 ,CAB OCF %D

A: Given data E=200000MPa P=36kN

Q: express each common fraction as a decimal fraction. 5⁄64

A: Given data:- The given each common fraction is, 564

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.