Answered: The modulus of elasticity are slightly…

The modulus of elasticity are slightly higher for ceramic materials, Polymers have modulus values that are smaller than both metals and ceramics.

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter9: Time, Temperature, And Mechanical Properties

Section: Chapter Questions

Problem 1CQ

See similar textbooks

Related questions

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 540 mm.…

Q: A 30m long aluminum bar is subjected to a tensile stress of 172 MPa. Find the elongation in mm if E…

Q: A solid circular bar is acted upon by tensile force of 20N. The diameter of circular Bar is 10 mm.…

A: Given Tensile force, F = 20 N Diameter of bar, d = 10 mm Change in Length of bar, L' = 0.2 m…

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 860 mm.…

Q: he stress-strain relation shown in figure below was obtained during the tensile test of an aluminum…

Q: If the maximum bending stress is 600 MPa, find the corresponding bending moment.

A: Given data Yield point=800 MPa Cross section=2 cm × 6 cm Bending stress, σb=600 MPa

Q: extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 540 mm.…

Q: A steel bar is heated from room temperature to 800C while it is free to expand. The bar will…

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 560 mm.…

Q: A mild steel specimen originally 300 mm long is pulled in tension with astress of 500 MPa. If the…

A: Given: The length of the specimen is 300 mm. The stress is 500 MPa. The modulus of elasticity is 200…

Q: A cylindrical polymer with a diameter of 10nm when stress is applied to it and a change in diameter…

A: Let the applied Force be F in Newton and A is the area of polymer.Area of…

Q: A specimen of aluminum having a rectangular cross section 10.4 mm × 12.6 mm (0.4094 in. × 0.4961…

A: So, stress can be defined as ; σ = PA P = Tension pull = 35900 A = 10.4 * 12.6 = 131.04 mm2 σ =…

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 900 mm.…

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 820 mm.…

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 660 mm.…

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 680 mm.…

A: FIND NA :y=36×95(952)-22×22(95-7-222)36×95-22×22y=22.637mmFIND MOI…

Q: A mild steel specimen originally 300 mm long is pulled in tension with a stress of 500 MPa. If the…

Q: For a bronze alloy, the stress at which plastic deformation begins is 275 MPa (40,000 psi), and the…

Q: This is a mechanical property of engineering materials that exhibits a slow deformation under long…

A: given - mcq to find -mechanical property of engineering materials that exhibits a slow deformation…

Q: b2 a M d2 d1 | A B L b1 Answer: M = i N-m

Q: The linear portion of the stress- strain diagram of steel is known as the Modulus of elasticity B…

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 760 mm.…

A: Given:- The length of beam=760 mmb1=34 mmd1=106 mmb2=20 mmd2=20 mma=7 mmAllowable tensile bending…

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 620 mm.…

A: Aluminum billets are extruded by forcing them through a die at either a high or low temperature.…

Q: An aluminum specimen originally 300 mm long is pulled in tension witha stress of 275 MPa. If the…

A: Given data σ=275 MPaE=75×109N/m2l=0.3 m

Q: The deformation per unit length is called C(A) Tensile stress O(B) Compressive stress OCC) Shear…

A: Strain : Strain is defined as the ratio of change in length upon original length , It is…

Q: A cylindrical bar of aluminum 1.75 in diameter is to be deformed elastically by application of a…

Q: 1. The most important mechanical properties of brittle materials is

A: The most important mechanical property of brittle material is compressive strength. The compressive…

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 880 mm.…

Q: An extruded polymer beam is sub]ected to a bending moment M. The length of the beam is L= 860 mm.…

Q: Stress-Strain Behavior 6.3 A specimen of copper having a rectangular cross section 15.2 mm × 19.1 mm…

A: Given: Tension force, F= 44,500 N Cross-section=15.2 mm×19.1 mm

Q: An aluminum alloy rod has a circular cross section with a diameter of 7mm. The rod s subjected to a…

Q: b1 Answer: 1= i 648.03 N-m Save for Later Last saved 2 hours ago. Attemnt

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 580 mm.…

Q: len A material has the stress-strain behavior shown in the Figure below. Calculate the toughness (T)…

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 500 mm.…

A: Determine the largest moment M that can be applied as shown to the beam.

Q: A 12-mm thick steel tire has a width of 110 mm and an internal diameter of 800 mm. It is heated and…

Q: Draw a tensile stress-strain curve for a typical semi-crystalline polymer such as LLDPE, and define…

Q: An extruded polymer beam is subjected toa bending moment M. The length of the beam is L = 500 mm.…

Q: The following can NOT be determined from a tensile test : a- Mdulus of rigidity b. Ultimate tensile…

A: A material used in engineering consists of various properties which are considered while designing…

Q: Piano strings are made of a fibre which is pulled taut. When the string is tapped in the centre by a…

A: Given, e = 0.2% σ = 100 MPa

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L= 760 mm.…

Q: Determine the percentage of ductility of a metal alloy having the following tensile stress-strain…

A: From the given tensile stress-strain diagram of a metal alloy, The strain at limit of…

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 760 mm.…

A: Given an extruded polymer beam is subjected to a bending moment M. It is required largest moment M…

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L= 740 mm.…

A: Determination of largest moment M

Q: Bulk modulus of elasticity is the ratio of (a) Tensile stress to tensile strain (b) Compressive…

A: Bulk modulus of elasticity is the ratio of compressive stress to volumetric strain . Bulk…

Q: A mild steel specimen with an original length of 300 mm long is acted on with a tensile stress of…

A: Given: Original length, l = 300 mm Tensile stress, σ = 500 MPa Modulus of Elasticity, E = 200 GPa

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 580 mm.…

Q: The deformation per unit length is called O a. Strain O b. Tensile stress O c. Shear stress O d.…

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L= 620 mm.…

Concept explainers

Dependence on mechanical properties

The mechanical properties of materials are those structures that include the reaction to the load used. Metal switching features determine the scope of the usefulness of the content and establish the expected service life. Machine structures are also used to help distinguish and identify material objects. The most common mechanical properties considered are strength, ductility, stiffness, impact resistance, and resilience to fractures.

Question

The modulus of elasticity are slightly higher for ceramic
materials, Polymers have modulus values that are smaller than
both metals and ceramics.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

If it is constrained between two supports A and B and is stress-free at 20 ℃, what would be the stress in the two materials when it is heated to 70 ℃, For Steel: Es = 210 GPa, Coefficient of expansion = 12x10^6/℃. For Brass: Eb = 105 GPa, Coefficient of expansion = 19x10^-6/℃
How can some high strength polymers such as Kevlar polymer have higher strength than some metals?
Calculate the stress and strain at each force interval. Plot a graph of the stress-strain curve. Estimate the yield point of the steel and note its location on the curve. Estimate the ultimate strength of the steel and note its location on the curve.
Material A is known as a high strength material and Material B has high toughness. Explain the difference between properties of Materials A and B.
Question 5 A steel component is subjected to a biaxial state of stress in which both stresses are tensile in nature, and having magnitudes 100 and 60 MPa. The plane at which the resultant stress has maximum obliquity with the normal (in degrees) is
Rotational stiffness
With the help of a diagram, contrast the stress-strain relationship with respect to ceramic and metalsWith the help of a diagram, contrast the stress-strain relationship with respect to ceramic and metals
At a temperature of 60°F, a 0.04-in. gap exists between the ends of the two bars shown. Bar (1) is an aluminum alloy [E = 10,000 ksi; v = 0.32; a = 12.5 x 10-6/°F] bar with a width of 3.0 in. and a thickness of 0.75 in. Bar (2) is a stainless steel [E = 28,000 ksi; v = 0.12; a = 9.6 x 10-6/°F] bar with a width of 2.0 in. and a thickness of 0.75 in. The supports at A and C are rigid. Determine (a) the lowest temperature at which the two bars contact each other. (b) the normal stress in the two bars at a temperature of 250°F. (c) the normal strain in the two bars at 250°F. (d) the change in width of the aluminum bar at a temperature of 250°F. (1) 3.0 in. 32 in. 2.0 in. B ↓ (2) 44 in. 0.04-in. gap Determine the lowest temperature, Tcontact, at which the two bars contact each other.
Given your understanding of what initiates and controls failure in materials, which of the following will increase the failure strength or lifetime of a test piece or component and why? a. Decreasing the difference between the maximum and minimum stress values, as this effects the stress concentration factor b. Decreasing the temperature below the brittle-ductile transition temperature, to make it harder C. Polishing to reduce surface defects Od. Increasing its volume, to give a larger cross sectional area Oe. Increasing the grain size so there are less grain boundaries to initiate failure
An aluminum alloy [E = 70 GPa; v = 0.33; a = 23.0×10-6/°C] bar is subjected to a tensile load P. The bar has a depth of d = 260 mm, a cross-sectional area of A = 14720 mm2, and a length of L = 5.5 m. The initial longitudinal normal strain in the bar is zero. After load P is applied and the temperature of the bar has been increased by AT = 46°C, the longitudinal normal strain is found to be 1680 µɛ. % D Calculate the change in bar depth d after the load P has been applied and the temperature has been increased. L P Answer: Ad = i mm
1. The tensile strength vs. temperature curves of aluminum are plotted below. Explain the meaning of these two curves. 400 Ultimate strength 300 Yield strength 200 100 -200 -150 -100 -50 50 100 150 200 250 Temperature, °C Strength, kPa
At a temperature of 60°F, a 0.04-in. gap exists between the ends of the two bars shown. Bar (1) is an aluminum alloy [E = 10,000 ksi; v = 0.32; α=α=12.5 x 10-6/°F] bar with a width of 2.5 in. and a thickness of 0.75 in. Bar (2) is a stainless steel [E = 28,000 ksi; v = 0.12; α=α=9.6 x 10-6/°F] bar with a width of 1.7 in. and a thickness of 0.75 in. The supports at A and C are rigid. Assume h1=2.5 in., h2=1.7 in., L1=31 in., L2=46 in., and Δ=Δ= 0.04 in. (A) Determine the lowest temperature, Tcontact, at which the two bars contact each other. (B) Find a geometry-of-deformation relationship for the case in which the gap is closed. Express this relationship by entering the sum δ1+δ2, where δ1 is the axial deflection of Bar (1), and δ2 is the axial deflection of Bar (2). δ1+δ2= _____in. (C) Find the force in the Bar (1), F1, and the force in Bar (2), F2, at a temperature of 225oF. By convention, a tension force is positive and a compression force is negative. IN KIPS (D) Find σ1 and σ2,…