The microwaves in a certain microwave oven have awavelength of 12.2 cm.Review | ConstantsPart AHow wide must this oven be so that it will contain five antinodal planes of the electric field along its width in the standing wavepattern?ΠΙ ΑΣΦ?L =SubmitRequest AnswerPart BWhat is the frequency of these microwaves?[ΠΙ ΑΣΦf =SubmitPart CRequest Answer?cmHz Suppose a manufacturing error occurred and the oven was made 6.0 cm longer than specified in part (a). In this case, what wouldhave to be the frequency of the microwaves for there still to be five antinodal planes of the electric field along the width of the oven?

Given : a Wavelength : 12.2 cmLength of oven : L = 6×λ2L = 6×12.22L = 36.6 cm

The microwaves in a certain microwave oven have a wavelength of 12.2 cm. Part A How wide must this oven be so that it will contain five antinodal planes of the electric field along its width in the standing wave pattern? ΫΠΙ ΑΣΦ ? L= Submit Request Answer Part B What is the frequency of these microwaves? IVE ΑΣΦ f= Submit Request Answer ? cm Hz

The microwaves in a certain microwave oven have a wavelength of 12.2 cm. Part A How wide must this oven be so that it will contain five antinodal planes of the electric field along its width in the standing wave pattern? ΫΠΙ ΑΣΦ ? L= Submit Request Answer Part B What is the frequency of these microwaves? IVE ΑΣΦ f= Submit Request Answer ? cm Hz

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Electrical Engineering How to measure the electric field intensity at 2m away from a Parallel coupled microstrip lines in HFSS?
Why are capacitance voltage dividers preferred for high ac voltage measurements?
Facts A clipper is a device that removes either the positive half (top half) or negative half (bottom half), or both positive and negative halves of the input AC signal. In other words, a clipper is a device that limits the positive amplitude or negative amplitude or both positive and negative amplitudes of the input AC signal. In some cases, a clipper removes a small portion of the positive half cycle or negative half cycle or both positive and negative half cycles. In the below circuit diagram, the positive half cycles are removed by using the series positive clipper. Question: In your own opinion. Why do we need to clip a certain amount of voltage in positive or negative or on both sides? What is the benefit of that in our devices or circuits in doing such thing?
A 3V sinusoidal signal with frequency 100 Hz amplitude is applied to channel A of an oscilloscope. A sinusoidal signal with the same frequency but opposite phase and amplitude of 1.5V is applied to channel B. What will be the equation of the Lissajous curve when the oscilloscope is switched to XY mode while the channels are at the same Volt/div setting?
4/. The cathode ray oscilloscope is used to display the applied ____________ in the output terminals. ac or dc signal current capacitance resistance
POWER SISTEMS high voltage technlque it is possible to measure pulsed (AND ANSWER THE SAME QUESTION FOR AC AND DC ) high voltages with the help of two spheres of equal radius placed on the same axis. In which case the approxlmate pulse voltage for pulse hlgh voltage , approxlmate voltage value for DC voltage , AND effective value for AC VOLTAGE voltage value that can be measured with such a system with diameters of 500 mm and known spacing between them is 2.5 cm, is given correctly. (Ambient conditions are neglected and take Ed = 30 kV / cm2 k = 0.9) a) 68,65114 kV b) 81.30081 kv c) 97,08737 kv d) 65,35947 kv e) 57.48835 kv f) 46.21612 kv PLEASE ANSWER THE THREE EQUESTION AND THE OPTIONS ARE THE SAME approxlmate pulse voltage for pulse hlgh voltage, approxlmate voltage value for DC voltage , AND effective value for AC VOLTAGE
A frequency modulated signal which is modulated by a 3-kHz sine wave reaches a maximum frequency of 100.02 MHz and minimum frequency of 99.98 MHz. Determine the peak frequency deviation in KHz. No unit in the final answer.
5. Compare the frequencies measured with the oscilloscope (Measured Menu and Cursors) to the function generator setting. What are the main sources of error in this measurement? An oscilloscope displays the waveform shown below. If the volts/div setting is set on 10 and the sec/div setting is on 1.0 ms, determine the peak-to-peak voltage and the frequency. 6. 109
What is Ferranti effect?
-) Below are two voltage patterns measured from an oscilloscope. The voltage stage of the CHI probe is 5 V / div, the CH2 probe voltage stage is 10 V / div and the time axis is 2ms / div. According to this information, a) What are the peak to peak and rms voltage values of the voltages in CHI and CH2? b) What is the frequency of the voltages in Hz? c) How many degrees is the phase difference between the two voltages, which voltage is leading?
8. Liquids with solid impurities a) Have higher dielectrie strength b) Of large size have higher dielectric strength c) Have lower dielectric strength as compared to pure liquids d) None of the above 9. Peak to peak ripple is defined as a) the difference between average de voltage and peak value b) the difference between maximum and minimum de voltage c) the difference between maximum ac and average dc voltages d) the difference between ac (rms) and average de voltages 10. In a Cockroft-Walton circuit, input voltage 100 kV load current 25 mA, supply frequency 100 Hz, each capacitor 10 nF. The optimum no. of stages for maximum output voltage is a) 1 b) 2 c) 10 d) 35
29) For the Double beam oscilloscope shown in Figure. Determine (a) the periodic time, (b) the frequency and (c) the peak to peak voltage of both waveform, (d) R.M.S. value of both waveform and (e) phase difference between the two waves. The time/cm switch is on 230µs/cm, the volts/cm switch for waveform A is on 28 V/cm and the volts/cm switch for waveform B is on 51000 mV/cm.