The mechanical system consists of two identical steel rods (A = 30 mm?, E = 200GPA, a = 15×106/°C) and a "rigid" beam AC. The beam is supported by a smooth pin at B. The nuts at A and C are initially tightened just enough to remove the slack, leaving the two rods stress-free. 1- Determine the axial stresses induced in rods (1) and (2) if the temperature of both rods is decreased by 60°C. 2- Determine the (small) angle 0 through which the beam AC would rotate due to this temperature change.

The mechanical system consists of two identical steel rods (A = 30 mm?, E = 200GPA, a = 15×106/°C) and a "rigid" beam AC. The beam is supported by a smooth pin at B. The nuts at A and C are initially tightened just enough to remove the slack, leaving the two rods stress-free. 1- Determine the axial stresses induced in rods (1) and (2) if the temperature of both rods is decreased by 60°C. 2- Determine the (small) angle 0 through which the beam AC would rotate due to this temperature change.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I am struggling with this question
The aluminum bar ABC has a cross-sectional area of 20 mm2 is supported by a pin at A and a steel wire at B. If P = 50 kN calculate the horizontal displacement of P. The cross- sectional area of the wire is 1.75 mm2, modulus of elasticity of aluminum is 70 GPa and the modulus of elasticity of steel is 200 GPa. D 90 cm 90 cm B 180 cm Ale 120 cm
In the figure, torsional moments act on a bar system of abruptly changing cross-section made of the same material. Accordingly, calculate the value of the factor α so that the support responses are of the same magnitude in absolute value. What must the torsional moment=Mb be for the D-end to be zero? Note: The shear modulus of the material is G = 80 GPa Mo= 10 kNm.
The assembly consists of two-rod brass C83400 copper alloy rods AB and CD of diameter 30 mm, a stainless 304 steel alloy rods EF and FG of diameter 40 mm, and a rigid cap H as shown in Figure 2. Neglect the size of the collar at F. Assume that the modulus of elasticity Esteel = 200 GPa and Ebrass = 101 GPa. If the force, P = 5 kN, (a) If the horizontal displacement of end G of rod FG is 0.6 mm, determine the new magnitude of P.
Please show the formula used and free body diagram A rectangular steel block is 4 inches long in the x direction, 3 inches long in the y direction, and 4 inches long in the z direction. The block is subjected to a triaxial loading of three uniformly distributed forces as follows: 48 kips tension in the x direction, 60 kips compression in the y direction, and 54 kips tension in the z direction. If ν = 0.30 and E = 29 × 106 psi, determine the single uniformly distributed load in the x direction that would produce the same deformation in the y direction as the original loading.
solve and draw fbd
( 48ll O O 2 9:YV The rod BD is made of material with G1= 135 GPa has a diameter 16 mm is bonded to the tube CA at point B, the tube made of material with G2=230 GPa has an outer diameter 37 mm and wall thickness of 7 mm. If T1=803 N.m and T2=1445 N.m, answer the following questions: A B T2 N-m 0.4 m 0.1 m 0.3 m T1 N-m The polar moment of inertia of the rod BD is Your answer The polar moment of inertia of the tube CA is
The assembly consists of two-rod brass C83400 copper alloy rods AB and CD of diameter 30 mm, a stainless 304 steel alloy rods EF and FG of diameter 40 mm, and a rigid cap H as shown in Figure 2. Neglect the size of the collar at F. Assume that the modulus of elasticity Esteel = 200 GPa and Ebrass = 101 GPa. If the force, P = 5 kN, (a) Sketch the free body diagram and calculate the internal forces acting in each section of the rod. (b) Determine the average normal stress developed in rods FG, EF and AB. (c) Determine the average normal strain in the rod of AB.(d) If the horizontal displacement of end G of rod FG is 0.6 mm, determine the new magnitude of P.
Problem #2 Calculate the increase in stress for each segment of the compound bar shown in the figure if the temperature increases by 110°F. Assume that the supports are unyielding and that the bar is suitably braced against buckling. Aluminum Steel A=1.5 in² A = 2.0 in² E = 10 x 10º psi E = 29 x 10² psl a=12.8 x 10/°F a = 6.5 x 10¹/°F TO 10 in 15 in dilman
A steel torsion bar AB with diameter d = 34 mm, and ductile material of tensile yield strength Sy = 276 MPa is attached to a rigid arm at A, supported by a bearing at C, and fixed at B, as the picture shows. At the right end of the arm is mounted the wheel on which the vertical force P acts from the ground and which passes through the center of the wheel. If bearing C acts as a simple support and the effect of transverse shear due to P is negligible, determine the maximum force P (in kN) that can be applied to the wheel. Consider a factor of safety n = 2.5. Use the maximum energy of distortion failure criterion and do the analysis on bar AB (torsion bar) in the section where the bearing is.
Brass Problem 3: A composite bar is made by attaching a copper rod of length 900 mm and diameter 30 mm and a brass rod of length 600 mm and diameter 45 mm as shown. A load of 20 kN is applied at 20°C. For unyielding supports, find the stresses in the materials when the temperature rises to 50°C. For copper, E = 120 GPa and a = 18 x 10-6 °C. For brass, E = 90 GPa and a = 20 x 106 °C. Copper 20 kN 900 mm 600 mm
‏The bars AB, CD and EF made of material with E=180 GPa and have a cross sectional area of 678 mm2. The beam ACE is subjected to the force P=163 N. Take L=1.6 m and d=519 mm. Answer the following questionsThe force in the barABThe force in the barCDThe force in the barEFThe stress in the bar ABThe stress in the barEFThe stress in the barCDThe elongtion in the bar ABThe elongtion in the bar EF