The maximum applied load on cylindrical diameter 150 mm and length 300 mm a concrete specimen of tested as per the split tensile strength test guidelines of IS 5816 : 1999 is 157 kN. The split tensile strength (in MPa, round one decimal place) of the off to specimen is

The maximum applied load on cylindrical diameter 150 mm and length 300 mm a concrete specimen of tested as per the split tensile strength test guidelines of IS 5816 : 1999 is 157 kN. The split tensile strength (in MPa, round one decimal place) of the off to specimen is

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.4P: A tensile test was performed on a metal specimen with a diameter of 1 2 inch and a gage length (the...

See similar textbooks

Related questions

Q: What is the shear force to be carried by the reinforcements of a beam subjected to axial tension if…

Q: 3- Explain various factors affecting workability of concrete. 4- Explain the factors which effect on…

A: 3. Factors affecting workability of concrete water content : increase in cement content of concrete…

Q: A concrete cylinder of diameter 150mm and length 300mm when subjected to an axial compressive load…

Q: 2. Calculate the minimum beam width for the beam shown below. The clear cover to the stirrups on all…

A: The aggregate size is s=1 in. The depth of the section is D=24 in. Take the compressive strength of…

Q: The permissible bending compressive strength for M 25 grade of concrete is 8.5 N/ mm². Its…

A: Given- M25 grade of concretePermissible bending compressive strength-σcbc=8.5 N/mm2It is needed to…

Q: The maximum applied load on cylindrical diameter 150 mm and length 300 mm a concrete specimen of…

A: Given: The diameter is 150 mm. The length is 300 mm. The applied load is 157 kN.

Q: Q3: B: Design the concrete mix according to the following conditions: Design Environment Building…

Q: The maximum applied load on a cylindrical concrete specimen of diameter 150 mm and length 300 mm…

A: Given data- Diameter of the specimen D=150 mmLength L=300 mmLoad P=157 kNTo Find-The split tensile…

Q: Q1: The compressive strength of a (10×10×10) cm Cube is 20 MPa at 7-day, determine the flexural…

A: Compressive strength of concrete at 7 day= 20 MPa compressive strength at 7 day=65% of Full…

Q: Problem 5: A beam is 250 mm in width, 500 mm in total height and 3.5 meters in length. This beam was…

A: Given data width of beam= 250mm Height = 500mm Length= 3500 mm compressive strength= 32MPa we have…

Q: At twelve days the modulus of rupture (MOR) test of a 6x12 cylinder is as shown on the table:…

A: Given, Cylinder diameter = 6 in Cylinder height = 12 in

Q: ve desic Q4) Concrete is required for walls of a building that will be moderately exposed to…

Q: Consider the following statements: The effect of an air entrainment in concrete is to 1. increase…

A: Air entrainment in concrete : Increased workability Increased resistance to freezing and thawing…

Q: FLEXURAL ANALYSIS CONCRETE UNCRACKED Problem: Determine the cracking moment for the section shown…

Q: 6. Calculate the compressive stress in a 6-in.-diameter by 12-in.-high concrete test specimen if the…

Q: A normal-weight concrete has an average compressive strength of 20 MPa. What is the estimated…

A: Flexural strength of concrete is between 10-20% of compressive strength ie 2-4 N/mm2 or MPa

Q: removed? Calculate the coefficient of creep for normal strength concrete years. Assume the loading…

A: Members have residual creep strain even after removal of creep load cause : The residual strain is a…

Q: A half-block concrete masonry unit is tested for compressive strength. Theoutside dimensions of the…

A: given data: outside dimension=190 mm ×190 mm×190 mm load=225 KN

Q: n the 28th day after concrete was mixed, a 6.00-in-diame a compressive testing at a load of 145 000…

Q: Calculate the tensile steel stress

A: given- a concrete beam 240 mm by 450 mm reinforced with 5-16-mm-dia and f'c = 21 MPa, fy = 420 MPa.…

Q: A round concrete column has a diameter D.A force of 800 kN act on the column as shown. The yield…

A: Diameter = 50.46 mm

Q: To evaluate the effect of a certain admixture on the flexure strength of concrete, two mixes were…

A: Modulus of rupture in bending is the maximum stress at failure and in torsion is the maximum shear…

Q: What is the shear force to be carried by the reinforcements of a beam subjected to axial tension if…

Q: 1. A normal-weight concrete has an average compressive strength of 4500 psi. What is the estimated…

Q: A normal-weight concrete has an average compressive strength of 20 MPa.What is the estimated flexure…

A: Given:- average compressive strength =20MPa To find:- estimated flexure strength

Q: The permissible bending compressive strength for M 25 grade of concrete is 8.5 N/mm². Its short-term…

A: Given data in question Permissible bending stress Grade of concrete To find out Short and long…

Q: A hollow concrete masonry unit has an actual dimension of 150mm x 200mm x 400mm (W x H x L). The…

Q: Chapter 13 Question: What is the elasticity of concrete for a normal weight mix (unit weight equal…

Q: The strength of a fully matured concrete sample is 500 kg/cm². When cured at an averag temperature…

Q: The maximum applied load cylindrical diameter 150 mm and length 300 mm on a concrete specimen of…

A: Given data: Diameter = 150 mm Length = 300 mm Maximum load applied = 157 kN = 157×103 N

Q: Consider the following strengths of concrete: 1. Cube strength 2. Cylinder strength 3. Split-tensile…

Q: 42. Permissible tensile strength of concrete, M150 is: A) 150kg/cm² C) 150N/mm? B) 15kg/cm D)…

A: The given data is: Grade of concrete = M150

Q: The flexural strength of a cross-section can be reduced by O A. Replacing larger bars by same number…

A: Note:- Hi! Thank you for the question As per the honor code, We’ll answer the first question since…

Q: The compressive strength is linearly correlated with the tensile strength of the concrete and…

A: The statement is false

Q: A normal-weight plain concrete beam is 6 in. x 12 in. is simply supported on a span of 4 ft…

Q: The third-point loading flexure strength test was performed on a IVI ... concrete beam having a…

A: From above figure 2P=35.7 kN P=17.85 kN The expression for maximum moment is given as…

Q: ined Concrete (Moderate) d Strength = 35 MPa d Slump = 6 inches m Size of CA = 3/4 inches ater =…

Q: Problem 5: A beam is 250 mm in width, 500 mm in total height and 3.5 meters in length. This beam was…

A: Given data Width = 250 mm Height = 500 mm Length = 3500 mm compressive strength= 32 MPa We have to…

Q: c = 25 mpa, fy = 414 the tensile stress is in the concrete is?

A: Given fc = 25 MPa fy = 414 Mpa

Q: Calculate the tensile steel stress

A: given- a RCC beam having 5-16-mm-dia rebars in a concrete beam 240 mm by 450 mm at ultimate stage if…

Q: . A split-tension test was conducted on a concrete cylinder with a 150 mm diameter and 300 mm…

Q: The rectangular beam shown in the figure is subjected to a factored moment Mu= 288 k-ft. ■ Calculate…

Q: It is the Standard Practice for Making and Curing Concrete Test Specimens in the Field A ASTM C192 B…

A: ASTM C192 is used for Standard Practice for Making and Curing Concrete Test Specimens in the…

Q: A rectangular beam has the dimensions (see Fig. 3.2b) b = 250 mm, h = 650 mm, and d = 600 mm and is…

A: Given data Rectangular beamwidth=b=250 mmdepth=h=650mmeff. depth=d=600mmArea of steel=As=1530…

Q: A normal-weight concrete has an average compressive strength of 20 MPa. What is the estimated…

A: "As per our guidelines we are supposed to solve the first question, kindly post the other question…

Q: Estimate the modulus of elasticity and the shear modulus of a concrete specimen with a dry density…

A: Estimate the modulus of elasticity and the shear modulus of a concrete

Q: The design engineer specifies a concrete strength of 5500 psi. Determine the required average…

A: (a) The specified concrete strength is 5500 psi. The expression for the average compressive strength…

Q: What is the dimension b and d of the specimen in mm?

A: given= a concrete specimen with equal sides having a span of 600mm and carrying a load of 100kn.…

Q: (a)Determine the Young's modulus for this particular concrete under

A: Givendata: Maximum compressive stress σE = 20x107 Pa. Maximum compressive strain e = 8x10-3.

Concept explainers

Electronic Spreadsheet

Tabular listing has many advantages ranging from time management to efficient scheduling of tasks. Electronic spreadsheets allow the user to tabulate and analyze data, using its easy-to-use interface. An electronic spreadsheet is a staple application used among accountants, management staff, and IT professionals. It is used in various sectors worldwide for data management. An electronic spreadsheet is a system and computer software that could be used to do numerical computations automatically. Spreadsheet application programs are often organized as a table with rows and columns. Each row and column intersect to form a cell, which may be used to store data. These data can take the form of a written label, a number, or a formula that combines information from other cells.

Question

Plzz answer

The maximum applied load
cylindrical
diameter 150 mm and length 300 mm
on
a
concrete
specimen
of
tested as per the split tensile strength test
guidelines of IS 5816 : 1999 is 157 kN.
The split tensile strength (in MPa, round
one decimal place) of the
off to
specimen is

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
A hollow aluminum tube is rigidly attached between steel rod and a bronze rod as shown. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in aluminum of 80 MPa, in steel of 150 MPa or bronze of 100 MPa. Steel Aluminum Bronze А P> ЗР - 2P outside = 30 mm d inside = 20 mm d d = 16 mm d = 60 mm -100mm- -150mm- -125mm-
Problem 1.5-2 A bar of length 2.0 m is made of a structural stoel having the stres-strain dingram shown in the figure. The yield stresa of the steel is 250 MPa and the slope of the initial lincar part of the stress-strain curve (modulus of elasticity) is 200 GP. The bar is loaded axially until it eklongates 6.5 mm, and then the load is removod. How does the final length of the bar compare with its orig- inal length? Hint: Ue the concepts illustrated in Fig. 1-36h) MP 300 200 100 0.002 0.004 0.006
The state of plane stress shown occurs at a critical point of a steel machine component. As a result of several tensile tests, it has been found that the tensile yield strength is o, = 250 MPa for the grade of steel used. Determine the factor of safety with respect to yield using (a) the maximum shearing stress criterion, and (b) the maximum distortion energy criterion. ↑y 40 40 MPa 80 MPa 25 MPa ➜X
3) An bronze rod is rigidly attached between a aluminum rod and a steel rod as shown. Axial loads are applied at the positions indicated. Find the maximum allowable value of P that will not exceed a stress in steel of 140MPA, in aluminum of 90MPA or in bronze of 100MPа. Aluminum A = 500mm? Bronze A = 200mm? Steel A = 150mm2 2P ЗР L st = 1.2m L br = 2m Lal = 3.5m
1.(e) The state of plane stress shown occurs at a critical point of a steel machine component. As a result of several tensile tests. It has been found that the tensile yield strength is o, = 250 MPa for the grade of steel used. Determine the factor of safety with respect to yield using (a) the maximum shearing stress criterion, and (b) the maximum distortion energy criterion. ↑Y 40 MPa 80 MPa 25 MPa
Steel 1 m Aluminum T 0.75 m Determine the maximum permissible value of T subject to the following conditions: tt S 80 MPa, Tal 50 MPa, and the angle of rotation of the free end is limited to 0.1 radian. For T. Hollow Solid d= 30 mm D= 40 mm %3D steel, G = 82 GPa and for aluminum, G= 28 GPa. %3D d = 30 mm %3D
This figure shows typical stress-strain behaviour for a brass. The inset figure shows the behaviour at low strains. 500 70 Tosle strength 450 MPa 166,000 ps 60 400 300 MP 40 30 200 Yeld steg 250 MPa (,0a 200 20아 100- 20 100 10 0.20 030 040 If the cylindrical test sample is initially 14cm long with an initial radius of 2mm, estimate the true stress in MPa at the ultimate tensile stress. (Enter your answer to the nearest whole number) an es
1.4-7 The data shown in the table below were obtained from a tensile test of high-strength steel. The test specimen had a diameter of 13 mm and a gage length of 50 mm (see figure for Prob. 1.4-3). At fracture, the elongation between the gage marks was 3.0 mm and the minimum diameter was 10.7 mm. Plot the conventional stress-strain curve for the steefor the steel and determine the proportional limit, modulus of elastics of elastic- ity (i.e., the slope of the initial part of the stress-strain,tress-strain curve), yield stress at 0.1% offset, ultimate stress, percent, elongation in 50 mm, and percent reduction in area. 'ess, percent area. TENSILE-TEST DATA FOR PROB. 1.4-7 Elongation (mm) 0.005 0.015 0.048 Load (kN) 5 10 30 50 0.084 60 0.099 64.5 0.109 67.0 0.119 68.0 0.137 69.0 0.160 70.0 0.229 72.0 0.259 76.0 0.330 84.0 0.584 92.0 0.853 100.0 1.288 112.0 2.814 113.0 Fracture
2. The Goodman diagram relates oa and om for fatigue failure after a specific number of cycles Nf, where da is the cyclic stress amplitude, and om the mean stress. For a steel specimen it is found that oa oa (0). [1- (om/OTS)] where Ors is the metal's tensile stress (375MPa), and oa (0)~0.450TS is the 107 cycle fatigue limit at zero mean stress. Assuming the specimen is cycled repeatedly between 0 stress and a peak stress, what is the maximum peak stress if failure in < 107 cycles is to be avoided? Ans: 233 MPa
A state of plane stress (σ3=0) occurs at a critical point of a mild steel machine component (see Figure 1 below). As a result of several tension tests, it has been found that the tensile yield strength is = 250MPa for the grade of steel used. (a) Determine the factor of safety (FS) with respect to yield using (i) the maximum shear stress criterion and (ii) the maximum distortion energy (von Mises) criterion. (b) Graph the Tresca Hexagon and the von Mises oval for this material and note the location of the given state of plane stress as a point on the graph.
As shown, an aluminium alloy construction BCD with a circular cross section is fixed at end B and affected by a force of 150 N at the free end D. The diameter of the cross-section a-a is 20 mm. The yield strength of the material is 80 MPa: a) Determine the stresses at point A of the a-a cross-section. As indicated in the picture, draw the stress element in Cartesian coordinates and specify the stress values.(b) Calculate the factor of safety, n for Tresca, and the von Mises yield criterion to see if the structure would yield based on the stresses at point A.(c) In the major stress area, draw the yield loci of both criteria and indicate the operational stress state & why is the Rankine failure criterion inappropriate for aluminium alloys?