The magnetic structure of a synchronous machine is shown schematically in Figurel. Assuming that rotor and stator iron have infinite permeability, i.e., (μ→∞). For I-10 A, N=1000 trns, air gap length g= 1 mm, and pole face area, Ag-2000 cm²; (a) Find the air-gap flux d (b) Find the magnetic field density Bg through the air gap. (c) Calculate the magnetic energy stored in the magnetic circuit. Figure 1 Stator Air gap length g N turns Pole face, area Ag Rotor 818 Air gap permeability Ho

The magnetic structure of a synchronous machine is shown schematically in Figurel. Assuming that rotor and stator iron have infinite permeability, i.e., (μ→∞). For I-10 A, N=1000 trns, air gap length g= 1 mm, and pole face area, Ag-2000 cm²; (a) Find the air-gap flux d (b) Find the magnetic field density Bg through the air gap. (c) Calculate the magnetic energy stored in the magnetic circuit. Figure 1 Stator Air gap length g N turns Pole face, area Ag Rotor 818 Air gap permeability Ho

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 6-pole generatro has 600 conductors. If the flux per pole is 20mWb, at what speed must the armature be drive to generate 240V if a) lap wound connection, or b) wave wound connection.
× 4:03 K s.eng.ruh.ac.lk □ Û 8. Figure 4 shows the core of a simple dc motor. The magnetization curve for the metal in this core is given by Figure 5 and Figure 6. Assume that the cross-sectional area of each air gap is 18 cm² and that the width of each air gap is 0.05 cm. The effective diameter of the rotor core is 4 cm. L It is desired to build a machine with as great a flux density as possible while avoiding excessive saturation in the core. What would be a reasonable maximum flux density for this core? ii. What would be the total flux in the core at the flux density of part (i)? iii. The maximum possible field current for this machine is I A. Select a reasonable number of turns of wire to provide the desired flux density while not exceeding the maximum available current. Flux Density, B (T) 2.8 སྤྲ ཤཱ ཀ ཀཱ བྷ ཀ ཡཱཾ བ ་ 1.2 1.0 0.4 0.2 4-48cm Figure 4 0 10 20 30 40 50 100 → Depth 4 cm -0.05 cm 200 300 500 1000 2000 Magnetizing Intensity, H (A.turns/m) Figure 5 Magnetization curve…
A rectangular moving coil of a milliammeter is woundwith 30 turns. The effective axial length of the magnetic field is 20 mm and the effective radius of the coilis 8 mm. The flux density in the gap is 0.12 T and thecontrolling torque of the hairsprings is 0.5 × 10-6 N m/degree of deflection. Calculate the current to give adeflection of 60°.
a. If the material is the ideal material, N1I1 = 200, NIA = 100 and NIB = 150 If I am ampersand, what is the flux density in the middle of the air gap? okay? Calculate by drawing the magnetic circuit. b. If the material is not the ideal material (µr), the core material of each winding Find the inductance in terms of parameters c. What is mutual inductance between windings? D. Check the magnetic equivalent circuit of this system that there are no leakage fluxes. draw assuming. New magnetic with leakage fluxes in mind How about a circuit, draw?
Example(6): A magnetic circuit containing an air gap is shown in Figure below. With the dimension as marked, calculate the current in the coil to establish a flux density of 0.6 T in the air gap. The core has the B - H characteristics. Repeat above but correct for fringing and lamination. Consider SF=0.95, FF 1.08 while is as above. 2 mm) A-5cm²
4. In this figure, considering the straight wire is very long, find the magnetic flux through the loop. If the loop is directly pulled away from the wire, find the emf induced and the direction of induced current in the loop. a a
Suppose that, in designing an electrical generator, we need to produce a voltage of 120 V by moving a straight conductor through a uniform magnetic field of 0.5 T at a speed of 30 m/s. The conductor, its motion, and the field are mutually perpendicular. What is the required length of the conductor? It turns out that in generator design, a conductor of this length is impractical, and we must use N conductors of length 0.1 m. However, by connecting the conductors in series, we can obtain the required 120 V. What is the number N of conductors needed?
The magnetic structure shown in the figure is built with a material whose magnetization curve is expressed by: (See image with the equation) The length of the mean magnetic path in the core is equal to 0.75 m. The measurements of the cross section are 6 × 8 cm 2. The length of the air gap is 2 mm and the flux in it is equal to 4 mWb (in the direction indicated in the Figure). Determine the number of turns in coil B. Ans: NB =1,237 turns (I need the procedure)
To a magnetic core, with a relative permeability of 2100, a current I1 of 1 A and a current I2 of 2 A are applied, where the number of turns of the winding is 1000. The depth of the magnetic core is 20 cm. take into account that the bounded measurements are given in centimeters. The air gap shown in the figure is 0.2 cm and has an effective area equivalent to 1.1 times the cross-sectional area of the core. Determine:a) The equivalent circuit with sources and reluctance (Graph it)b) The magnetic flux of the central columnc) Magnetic induction at point Ad) Explain what would happen if the flow of current I1 is reversed
Amagnetic circuit has an average length of 1.4 m and a cross-sectional area of 0.25 m2. Excitation is provided by a 140 -turn, 30-Q, coil. Determine the voltage required to establish a flux density of 1.56 T. The reluctance of the magnetic circuit, when opera ting at this flux density is 768 A-t/Wb.
A 4pole lap wound armature when driven at 600rpm generates 120V. if the flux per pole I 25mWb, find the number of armature conductors.
Scenario: Consider a magnetic circuit with a mean length of 0.6 m. A 4x10? turn coil is wound around the left-hand limb. The magnetic circuit is made from silicon steel; core effects may not be ignored. The cross section is uniform and there is a 1.1 mm air gap in the circuit. Find the current required in the coil to give a flux density of 1.40 T in the air gap. The number of turns in the coil is The magnetic field intensity in the core, He. is A-t/m. The current in the coil, i, is A. (keep two decimals)