The liquid in the figure has a specific gravity of 3.0. The gage pressure Pa=70Kpa and Pb is atmospheric. The orifice is 75mm⌀ and C=CV=0.95 with h=1.5m, determine the discharge and the head loss in the orifice.

Q: A pipe carrying oil of specific gravity 0.877 changes in size from 150 mm at section 1 and 450 mm at…

A: Given data Specific gravity(SG) = 0.877 Diameter at section 1 = 150 mm Diameter at section 2 = 450…

Q: A turbine is supplied with 0.6 m³/s of water from a 0.3m diameter pipe; the discharge pipe has a…

A:

Q: Water at 20°C is flowing through a horizontal nozzle at a flow rate of 0.005 m3/s. At the nozzle…

A:

Q: d iron pipe system whose diameter is 0.75 inches and flow rate is 0.020 cfs. Do you agree with the…

A:

Q: 1) At the instant the valve is opened, the Venturi meter indicates a pressure difference of 735 kPa.…

A:

Q: Ex 6: If oil (SG=0.9) is flowing at a rate of 0.06 m/s, determine the difference in pressure between…

A: Given data:- Specific gravity of oil, SG=0.9 => density of oil, ρ=900kgm3 Discharge, Q=0.06m3s…

Q: 1. Is steady flow a good approximation for this problem? Why?2. What assumption will you use about…

A: Given data as per question

Q: The pumper truck shown in the figure below is to deliver 1.6 fts to a maximum elevation h of 61 ft…

A: To find : determine the power that the pump must add to the water. Given : flow rate Q=1.6 ft3/s…

Q: A pipe carrying oil of specific gravity 0.877 changes in size from 150 mm at section 1 and 450mm at…

A: Given, Q=150 lit/secS.G=0.877d1=150 mmd2=450 mmz1=0z2=3.6 mp1=90 kPap2=60 kPa

Q: The impact force exerted by water on the reduction element (spacer for reducing the pipe diameter)…

A: The solution of this question would require the impulse momentum equation, Bernoulli's equation and…

Q: Q1: A pipe connecting a reservoir to a turbine which discharges water to the down through another…

A:

Q: Water is pumped though the system bellow using a 6 hp pump. Pipe 1 is from exit Q1 to point b and…

A: Inorder to find out the pressure at point B, first of all, we need to find the discharge in the pipe…

Q: A nozzle meter, with an orifice diameter of 3 cm, is being used to determine the velocity of ethanol…

A: Write the given data with suitable variables: Do=3 cm=0.03 mSG=0.789μ=0.986×10-3 Pa-s100 cm1 mD1=6…

Q: venturi meter is introduced in a 300 mm diameter horizontal pipeline carrying a liquid under a…

A: Diagram and solution is attached below:

Q: 2gh (YNg-Yw20) YH20 A2

A:

Q: In the figure below, the losses up to section A is 5V,2/2g and the nozzle losses are 0.05V," /2g…

A: Given data as per question Height H =8 m D1 =150 mm D2 =50 mm calculations Water is incompressible…

Q: The vertical orifice shown in the figure is 70 mm in diameter with Cy = 0.96 and the fluid is oil…

A:

Q: Water flows at the rate of 0.80m3/s in a 900-m long pipe. The total head loss in the pipe is 4m.…

A: GIVEN DATA - Q=0.80 m3/s L=900m h=4m f=0.018 We have to find diameter of pipe using Darcy-Weisbach…

Q: Example the bottom and upper end respectively. The intensity of pressure at the bottom end is 350…

A: The entire mechanical energy of the flowing fluid, which includes the gravitational potential energy…

Q: Q3: The 6-cm-diameter pipe as shown in Figure H.I contains glycerin (p = 1260 %3D kg/m', u= 1.49…

A:

Q: 08. The turbine shown in Figure develops 2500 kW when the water flowrate is 20 m'/s. The head loss…

A: Given: Assume the diameter of the pipe as 2 m.

Q: Turbulent water flows through the pump at 0.1 m /s. Total head losses between 1 and 2 are 15 m, and…

A:

Q: 3. In the figure shown, oil with specific gravity of 0.80 flows down at the rate of 15 m³/s. The…

A:

Q: 1. A pipe carrying oil of specific gravity of 0.877 changes in size from 150 mm at section 1 and 450…

A: GivenS.G=0.877d1=150mmd2=450mmZ2=3.6mP1=90kPaP2=60kPaQ=150L/s=0.150 m3/s

Q: A venturi meter is introduced in a 300 mm diameter horizontal pipeline carrying a liquid under a…

A: Given data: D=300 mmd=100 mmP=150 kPaHead loss=3% of differential pressure headhloss=-400 mm Need to…

Q: a! Water flowing through a tapering pipe having diameters of 300mm and 150mm at section one and two…

A: Calculate the velocity at section 1. v1=QA1 Here, Q is the discharge, v1 is the velocity at section…

Q: Two pipes are connected in series with a diameter ratio of 2:5. If the flow velocity in the smaller…

A:

Q: Water at 20°C is flowing through a horizontal nozzle at a flow rate of 0.005 m3/s. At the nozzle…

A:

Q: Q2. The turbine shown in figure 2 develops 3000 kW when the water flowrate is 24 Is. The head loss…

A:

Q: pump shown in the figure pumps 0.03 m' of water per second from the large reservoir through the pipe…

A:

Q: Q2/: As shown in the figure, the Assumptions of the flow through the venturi is steady,…

A: (1) Draw the diagram of the venturi meter.

Q: The flow rate of water through the pipe system shown in the figure is 25 lit/s under the total head…

A: To find :- The total head loss and the diameter of pipeline C. Given:- The flow rate of water is Q =…

Q: The device shown in the fugure below is known as a venturi. In theis specific venturi the…

A: Given:P1-P2=5psiD2D1=0.35D2=8in=812fthere,P1 and P2=Pressure at section 1 and 2 of venturiD1 and…

Q: 1. The pressures at points 1 and 2 are 150 kPa and -35 kPa, respectively with flow rate of seawater…

A:

Q: Problem 5: A pressurized tank of water has a 10-cm-diameter nozzle at the bottom, where the liquid…

A: Taking point 1 above liquid surface and point 2 just after nozzle exit.

Q: The 600-mm pipe shown in Figure 8 conducts water from reservoir A to a pressure turbine, which…

A:

Q: Q2. The turbine shown in figure 2 develops 3000 kW when the water flowrate is 24 m /s. The head loss…

A:

Q: Problem 2: The device shown in the figure is known as a venturi. In this specific venturi, the…

A: P1-P2=5 psiD2D1=.35D2= 8 inchesz1=z2 since horizontal vernturimeterNow apply bernoulli equation…

Q: C3. An oil of specific gravity 0.81 is flowing through a horizontal venturimeter fitted to a 260 mm…

A:

Q: In the test of the reaction turbine, the water flowing over the weir in the tailrace was found to be…

A:

Q: The vertical orifice shown in the figure is 70 mm in diameter with Cv = 0.96 and the fluid is oil…

A: Orifice diameter, d=70 mm=0.070 Coefficient of velocity, Cv=0.96Depth of oil up to the center of the…

Q: Water flows steadily into the Venturi tube in the following figure. In the section considered,…

A: Given data: -  The entrance area is A1 = 20 cm2. The throat area is A2 = 10 cm2. The weight density…

Q: An oil of specific gravity 0.85 is flowing through a horizontal venturimeter fitted to a 240 mm…

A: Given details:  Soil=0.85Smercury=13.6Dinlet=240mm=0.24mDthroat=98mm=0.098X(mercury level)=835mm of…

Q: For this siphon the elevations at A, B, C, and D are: 30 m, 32 m, 27 m, and 26 m, respectively. The…

A: Given Data Elevation are : A=30 m,B=32 m,C=27 m,D=26 m Diameter of pipe is : d=25 cm =0.25 m…

Q: A water pipe is laid on a slope of 1 in 40. The pipe is 50 m long. Water flows downwards at the rate…

A: Given   Flow rate, Q = 0.06 m3/s           Slope = 1/40     Length, L = 50 m Diameter, D = 400 mm…

Q: Water at 20°C is flowing through a horizontal nozzle at a flow rate of 0.005 m³/s. At the nozzle…

A: Given Data: Discharge rate, Q=0.005 m3/s Inlet diameter, d1=5 cm

Q: A turbine, at the end of a pipeline 1800 m long, beneath a dam, produces 200 kW of power, when the…

A:

Q: From a very large tank with an absolute pressure of 3 bar, the water is discharged to the atmosphere…

A:

Q: A 50 mm diameter siphon discharges oil (SG=0.88) from a reservoir (elev. 20m) into open air (elev.…

A:

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.