The flow rate of water through the pipe system shown in the figure is 25 lit/s under the total head loss of 10m. Assume C = 120 for all pipes. Determine the total head lost and the diameter of pipeline C. Line A L=250m, D = 150mm Line B L=270m, D = 150mm L=200m, D = ? Line D L=500m, D=200mm

The flow rate of water through the pipe system shown in the figure is 25 lit/s under the total head loss of 10m. Assume C = 120 for all pipes. Determine the total head lost and the diameter of pipeline C. Line A L=250m, D = 150mm Line B L=270m, D = 150mm L=200m, D = ? Line D L=500m, D=200mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3. Petrol is drained from a tank X to tank Y via pipeline A-B (see figure Q3). A pump is then used to pump the petrol from tank Y to tank Z via pipeline C-D. Pipe lengths, diameters and relative heights of the pump and tank levels are as shown in figure Q3. The density of the petrol is 760 kg/m³ and the Fanning friction factor (f) for all the pipes is 0.0075. • For pipe A-B the entrance loss at A is 0.5 • For pipe C-D the entrance loss at C is 0.5 u² • All valve losses are 0.2 each, 2g Neglect any entrance or exit head losses at the pump and all other pipeline component losses. X • The velocity in the pipe C-D cannot exceed 1.8 m/s The pump mechanical efficiency is 86% 10 m L = 50 m D = 100 mm B 00 30 m Y 5m 20 m and the exit loss at B is and the exit loss at D is D = 75 mm L = 10 m Figure Q3 D = 75 mm L = 50 m pump 2g N 10 m
On a circular conduit there are different diameters: diameter D1 = 2 m, changes into D2 = 3 m. The velocity in the entrance profile was measured: v1 = 3 m/s. Calculate the discharge and mean velocity at the outlet profile (see figure below). Determine also type of flow in both conduit profiles (whether the flow is laminar or turbulent) – temperature of water T = 12° C. (use Reynold’s number Re), For laminar flow: Re<2320, For turbulent flow Re>2320, Kinematic viscosity of water of 12°C, v is equal to 1,24 10^-6 m2/s.
Use f=0.012 for all pipes and initially assume equal flow in pipes AB and AE. Determine the corrected flow in pipes BC, BE, AB, DE, and AE of the pipe network shown. 0.6 m/s A 300m B 300m 0.4 m/s 300mm 250mm 424m 300m 300m 250mm E 300mm 250mm 300m D 0.2 m/s 250mm
4
Starting from the Bernoulli equation and conservation of mass equation, derive the flow rate equation for the pipe shown in Figure Q2. Then, determine the magnitude of the flow rate.
Question 1: Water is expelled by a jet to the environment (i.e. the water flow is surrounded by atmospheric pressure). To change the direction of the water flow, this enters to a curved pipe as show in the figure (top view perspective). Calculate the forces exerted by the flow to the pipe in x and y direction (both horizontal). Use a water density of 1000 kg/m³, Q=1 m³/s, diameter d-0.3 m. Follow the 4 steps explained in the lectures and state your assumptions clearly. 30 Question 2: Repeat question 1 but change the curvature from 30 degrees to 90 degrees. How the forces change? 90
Problem Consider a cylindrical pipe of length L and diameter D = 2R. The angle that the axis of the pipe forms with the vertical direction is a. Assume that when the fluid enters the pipe its velocity is uniform (i.e., it has the same value over the entire cross-section of the pipe) and equal to U in the axial direction. In the radial and angular directions, the velocity is zero. So, it is: 2 =0: v(r, 0, 2) = Ue, (1.1) Here v is the fluid velocity and e, is a vector of unit magnitude parallel to the coordinate axis z; furthermore, we have assumed that the pipe inlet is located at z = 0. Near the entrance of the pipe, the velocity profile varies in the axial direction. But after a certain entrance length, the profile becomes fully developed, no longer changing with z. The evolution of the velocity profile is sketched in Fig. 1, where, for clarity, the pipe inclination is not shown. The entrance length is denoted by L.. For z > L., the fluid velocity is no longer a function of the axial…
solve below
In Figure 1, water flows vertically downwards in a trococonical tube. Diameters are D1=40 in ; D2=20in and the height of the device H=6 ft .If the flow is 1 ft³/s, find the pressure difference between the ends of the pipe
Please don't copy the answer from the online pdf. I need explanation+diagram
If the water surface elevation in reservoir B is 110 m, what must be the water surface elevation in reservoir A if a flow of 0.03 m^3/s is to occur in the cast iron pipe. Use f= 0.0021 for all pipes. (DO NOT ROUND OFF)
P = Patm 1 Vį = 6.9 m/s Flow h = 0.89 ft water 2 Density of water = 1000 kg/m³ Determine the pressure at the point 3?