The light boom AB is attached to a vertical wall by a ball and socket joint at A and supported by two cables at B. A force P is applied at B where P = 17i - 11j kN.Note that the reaction force at A acts along the boom because it is a two-force member. Calculate the magnitude of the reaction force at A in kN. 2m 4 m 6 m y 3. A Answer: Calculate the magnitude of the tension in cable BD in kN. Answer:

The light boom AB is attached to a vertical wall by a ball and socket joint at A and supported by two cables at B. A force P is applied at B where P = 17i - 11j kN.Note that the reaction force at A acts along the boom because it is a two-force member. Calculate the magnitude of the reaction force at A in kN. 2m 4 m 6 m y 3. A Answer: Calculate the magnitude of the tension in cable BD in kN. Answer:

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Start Consider the structure shown below (CD is a cable). 3a yllabus Da D sments aces 3a A В C 30 kN/m If P = 95 kN and a = 1 m, Determine the support force reaction at A.
a. If the tension in the cables is 150 kN, determine the reaction at the fixed end at E. b. For what value of the cable tension force would the moment at E be zero? A 20 kN 1.8 m B 20 kN 1.8 m 20 KN 1.8 m 20 kN 1.8 m D с E 4.5 m F 2.25 m 3.75 m
The hanging structure in the figure below is homogeneous. Its weight (40 kg) is acting at the center of the rectangular slab, parallel with the z-axis. Determine the magnitude (in N) of the force acting along the cable at point D. A 500 40 kg y C. 250 550 750 -550-
For the calble shown .in, determine the following: q. reactions for the cable b. the sag y at the 55-kip load C. cable length A 30ft 55 kips 6 5 kips 95 kips -50ft -50f *30ft -30ft 30ft. CS Scanned with CamScanher
7. Determine the horizontal and vertical components of reaction at the pin A and the tension developed in cable BC used to support the steel frame. TI 60 kN B ImIm- -1m- T 3 m A 30 kN - m
Show how the angles are gotten and step by step solution
Answer with complete fbd on solutions
Please solve
Calculate the magnitude of the reaction at A
The light boom AB is attached to a vertical wall by a ball and socket joint at A and supported by two cables at B. A force P is applied at B where P = 14i - 16j kN.Note that the reaction force at A acts along the boom because it is a two- force member. Calculate the magnitude of the reaction force at A in kN. 2m 4 m 6 m y A 6m u 7.
A- In Fig.A , Replace the loading system by an equivalent resultant force and specify where the resultant's line of action intersects the member AB measured from A. B- In Fig.B , A load Q is applied to pulley C, which can roll on cable ACB. The pulley is held in the position shown by a second cable CAD, which passes over pulley A and supports a load P. Knowing that P = 750 N, determine (a) the tension in cable ACB. C- In Fig.C, Determine the components of reaction at B. 1 m 3 m 20 N.m 1m A 1m В 25° 16 kN D 155 C 12 kN 10 kN 6 m Fig. Fig.A 600 N 800 N m B 1.5 m 1.5 m 2 m 2 m 45 D Fig. C
Q.1 The rigid beam is supported a pin connection at A and a cable BD at point the. Diameter of pin 3x at A is 20mm and Diameter of cable BD is 30mm. D P 15 (kN) x-2.7(m) 4х 4x Calculate the followings a) Support reactions at A and the axial force in Cable BD. b) Find the axial stress in cable BD and shear stress at pin A in the case of Double shear at A. c) Calculate the deformation and final length of BD if the modulus of elasticity E=200GPA d) Calculate the change in diameter of BD if the Poisson ratio v-0.3. |