Q.4) Rod AB is in the x-y plane and supported by two cables as shown. The tension in cable AC is 910 N and the tension in cable AD is 585 N. (a) Determine the angle between cables AC and AD. (b) Determine the magnitude of the combined projection of the forces in cables AC and AD onto rod AB. 2.4 m 1.2 m 3 m 2.6 m 1.8 m 2.4 m

Q.4) Rod AB is in the x-y plane and supported by two cables as shown. The tension in cable AC is 910 N and the tension in cable AD is 585 N. (a) Determine the angle between cables AC and AD. (b) Determine the magnitude of the combined projection of the forces in cables AC and AD onto rod AB. 2.4 m 1.2 m 3 m 2.6 m 1.8 m 2.4 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A transmission tower is held by three guy wires attached to a pin at A and anchored by bolts at B, C, and D. If the tension in wire AB is 110 lb. (a) Determine the vertical force P exerted by the tower on the pin at A. (b) Determine the moment about point O of the Resultant Force.
Please be clear
4. For the beam and loading shown, determine the tension in the cable and the support reactions at hinge A. Neglect the thickness of the beam and the size and friction of the pulley at E. E 2 kipsft 3 ft 3 ft 2 ft 10 kips 5. Find the maximum weight of the bucket that the wire system can support so that no single wire develops a tension more than 500 N. 3/3 25° 1300 300
The frame ABCD is hinged at A and D and is supported by a cable that passes through a ring at B and is attached to hooks at G and H. Knowing that the tension in the cable is 450 N, determine the moments about the diagonal AD of the force exerted on the frame by portion BH and portion BG of the cable.
Can you please answer these two questions?
Engineering Mechanics Answer this question ASAP
The block shown in the figure has a250 kg mass. The despicable weight bar ABrests against a smooth vertical wall in theend B and is supported by end A with aball joint. The two cables areconnected at the midpoint of the bar.Determine the reactions at supports A and B and thevoltage on the DC cable.
In this statics problem I am given a triangular distributed load on a cable. Attached is the given info for the problem. I know the basic steps to complete the problem but I am having issues figuring out where the triangular distributed load and 15 degrees given work into the problem. I’ve tried finding the Moment around B with the distributed load and then the two components of Tension at A (using sin(15) and cos(15) respectively but this did not work.
The transmission tower OA is being hoisted into position by the cables AB and AC. The resultant of the cable tensions P and Q, along with the 2400-lb weight of the tower, is a force R acting at point O. Determine P and Q. 40 ft 28 ft 69 ft 32 ft 2400 lb 20 ft 20 ft 36 ft A P=1063lb ; Q=915|b B P=1360lb ; Q=519lb C P=1063lb ; Q=951|b P=915lb ; Q=1063lb
Q3: A telephone cable is clamped at A to the pole AB. Knowing that the tension in the left-hand portion of the cable is T1 = 800 lb, determine by trigonometry (a) the required tension T2 in the righthand portion if the resultant R of the forces exerted by the cable at A is to be vertical, (b) the corresponding magnitude of R. 25° T₂
03.
The frame ACD is hinged at A and D and is supported by a cable that passes through a ring at B and is attached to hooks at G and H. Knowing that the tension in the cable is 625.00 N, determine the moment about the diagonal AD of the force exerted on the frame by portion BG of the cable. y 0.925 m 0.35 m G 0.5 m B 0.875 m 0.5 m P H D 0.75 m 0.75 m The moment about the diagonal AD of the force exerted on the frame by portion BG of the cable is N.m.