The ladder of the fire truck rotates around the z axis with an angular velocity of w₁ = 0.20 rad/s, which is increasing at 0.16 rad/s². At the same instant it is rotating upwards at w₂ = 0.61 rad/s while increasing at 0.43 rad/s². (Figure 1) Figure 40 ft 30 < 1 of 1 > Part A Determine the velocity of point A located at the top of the ladder at this instant. Enter the components of the velocity in feet per second to three significant figures separated by commas. VAz.Ay.Az Submit Part B Az.Ay.Az = Submit AΣ vec Request Answer Provide Feedback Determine the acceleration of point A located at the top of the ladder at this instant. Enter the components of the acceleration in feet per second squared to three significant figures separated by commas. 195| ΑΣΦ | 11 | vec Request Answer 4 ? C ft/s ? ft/s²

The ladder of the fire truck rotates around the z axis with an angular velocity of w₁ = 0.20 rad/s, which is increasing at 0.16 rad/s². At the same instant it is rotating upwards at w₂ = 0.61 rad/s while increasing at 0.43 rad/s². (Figure 1) Figure 40 ft 30 < 1 of 1 > Part A Determine the velocity of point A located at the top of the ladder at this instant. Enter the components of the velocity in feet per second to three significant figures separated by commas. VAz.Ay.Az Submit Part B Az.Ay.Az = Submit AΣ vec Request Answer Provide Feedback Determine the acceleration of point A located at the top of the ladder at this instant. Enter the components of the acceleration in feet per second squared to three significant figures separated by commas. 195| ΑΣΦ | 11 | vec Request Answer 4 ? C ft/s ? ft/s²

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question 4 What is relation between product tolerance (engineering tolerance) and process variation.? Explain in some details showing some representation. Analyze the following study in terms: Components of variations and their contributions X Chart and R Chart 3. Calculate the process capability (show your method). Is it acceptable? Comment on this result.
Calculate to the correct number of significant figures. (9443+45-9.9)x8.1x10^6
2 1.54 Explain how you would go about estimating the C and n values for the four tool materials shown in Fig. 21.17.
forming proceɛɛ. 17) Tension is the only type of stress applied in 18) rolling mill type are associated with relatively small diameter rolls in contact with the work piece. 19) Straining a sheet of metal around a straight axis is called 20) The extra portion which must be separated from the extrudate by cutting it just beyond the die exit is called 21) In sheet metal forming the area to volume ratio is considered to be mm. 22) In rolling, if the maximum dratt is 12 mm, & the coefficient of friction is 0.2, thus the minimum roll diameter is 23) The starting work piece in steel hot rolling of plate and sheet stock is called a 24) are 3 methods that can be used to control the metal flow under the blank holder in deep drawing process.
aragraph v F 1 Normal 1 No Spac... Heading 1 Heading 2 85.00 50.00 25.00 A blanking operation is to be performed to create the part shown below out of 2-mm thick half- hard 405 stainless steel. Provide (a) a drawing showing the punch dimensions; (b) a drawing showing the die dimensions; (c) the blanking force necessary. Note: you will need to translate tensile strength to shear based on the conversion from the text and use material properties from the text as well, tensile strength of 405 can be found in Ch. 6 (Metals). All dimensions noted below are in mm. hp 25.00 T Title 25.00 Subtitle Subtle Em... Emphasis DI Styles
(i) A pump manufacturing company has to assemble bearing on the shaft in large quantities. The time study shows 134 seconds as an observed time for the assembly operation. Determine the standard time with fatigue and personal allowance as 8% and 5%respectively. Level factor for this time study is 0.8.
Question # 4 A cup of height h=30 mm and diameter d = 50 mm is to be drawn from a steel sheet of 2 mm thickness. a) Calculate the blank diameter Db. b) The Drawing ratio (DR). c) The shearing force needed to cut this blank if the shear strength of the steel sheet is S=180 N/mm2
Q2) Choose the correct answer for only 15 (fifteen) of the following. is about 67% of the total forces. A) Longitudinal force. 1) In turning operation, the force. E) thrust force. B) Radial C) feed force. D) cutting force. (C) 2) Which one of the following materials has the lowest hardness: (a) aluminum oxide, (b) cubic boron nitride, f) none of the previous answers. high-speed steel, (d) titanium carbide, or (e) tungsten carbide Which one of the following operations is generally capable of the closest tolerances: (a) broaching. (b) drilling, (c) end milling, (d) planning, or (e) shaping. F) none of the previous answers. 3)
An experiment to determine the effect of four different types of engine oil (A, B, C, and D) on the rolling friction coefficient of a car speed has been conducted. Three brands of car (Honda, Toyota, and Mazda) were chosen, and each engine oil was tested twice on each car, producing the following ANOVA output in Figure 2. i) How many treatments involved? Write down all the treatments.ii) Identify the number of replication for each treatment. iii) Based on the ANOVA table above, find the values of W, X, Y and Z. iv) Test the interaction effect on rolling friction coefficient of car speed between the four different types of engine oil and the three different brands of car. v) Do we need to test for marginal effect? Give a reason.
1. “The grain size of metal sheet influences its formability in two opposing ways. The yield strength of a metal increases as the grain size decreases. So, the formability of a component may decrease if the grain size gets too small. Larger grained metals have better formability, but the roughened surface that results from stretching metal with grain sizes that are too large is unacceptable for many applications. During a recrystallization anneal new grains form in the metal. The final grain size depends on the annealing temperature and annealing time.” As shown in the figure below (1"x1" area under a 50Xmagnification microscope), a cold-rolled metal has been annealed at 550 degrees C for one hour. Calculate the ASTM Grain Size Number for the following condition: image attached
I need answer within 20 minutes please please with my best wishes
Using the figures in Table 1, forecast the number of surgeries in year 9 using a 3-year moving average and exponential smoothing using an alpha of 0.20and assuming that the forecast for period 8 is 750