Complete the following comparison table with the possible answers indicated in each comparison factor: Volumetric deformationComparison factorSurface area/volume ratio:High, LowBasic operations:Rolling, bending, cutting, forging,Sheet metal workextrusion, deep drawing, drawing.Shape of raw material:Sheets, strips, cylindrical billets,rectangular bars, rolls.Tools used:Die, piston, punch, rollersWorking temperatures:Cold, warm, hot

comparison factor volume deformation sheet metal work surface area/volume ratio; the area of…

Comparison factor Volumetric deformation Sheet metal work Surface area/volume ratio: High, Low Basic operations: Rolling, bending, cutting, forging, extrusion, deep drawing, drawing. Shape of raw material: Sheets, strips, cylindrical billets, rectangular bars, rolls. Tools used: Die, piston, punch, rollers Working temperatures: Cold, warm, hot

Comparison factor Volumetric deformation Sheet metal work Surface area/volume ratio: High, Low Basic operations: Rolling, bending, cutting, forging, extrusion, deep drawing, drawing. Shape of raw material: Sheets, strips, cylindrical billets, rectangular bars, rolls. Tools used: Die, piston, punch, rollers Working temperatures: Cold, warm, hot

Welding: Principles and Applications (MindTap Course List)

8th Edition

ISBN:9781305494695

Author:Larry Jeffus

Publisher:Larry Jeffus

Chapter23: Fabricating Techniques And Practices

Section: Chapter Questions

Problem 11R: What is the difference between plate and sheet material?

See similar textbooks

Similar questions

Sheet Forming Processes; V-Bending of Sheets is more expensive than Edge Bending. (T or F)In Metal Forming Processes there are 2 Basic Categories; Bulk Deformation Sheet Metalworking (T or F)In Sheet Metalworking there are 3 types of processes used; Bending Drawing Cutting (T or F)An Advantage of Hot Rolling is the process produces a final product with Small Tolerances (T or F)Direct Extrusion produces Hollow or Semi-Hollow types of Cross-Sections. (T or F)Designing a metal sheet product in the elastic zone of the Stress-Strain curve gives a longer life cycle for the products service (T or F)In the Bulk Deformation, Drawing Process, there is Tension Residual Strain. (T or F)Hot Rolling metal prevents residual stresses from building up in the made product (T or F)
For the mass production of flat metal sheet shapes; Waterjet cutting is the most appropriate manufacturing solution Stamping is used to obtain the sheet geometry Casting is an optimal solution Laser cutting is the optimal choice
Major metal forming processes include ______ a rolling to reduce the thickness for making metal sheets, strips, bars, structure shapes, and pipes. b forging to produce parts with higher strength c extrusion to produce hollow shapes, and shapes with muliple longitudinal cavities. d all of the above.
View Help RCM -EEE A Paragraph ¶ AaBbCcDc AaBbCcDc AaBbC AaBbcct AaB AaBbCct AaBbCCDA AaB 1 Normal 1 No Spac... Heading 1 Heading 2 Title Subtitle Subtle Em.... Emp Styles A cup-drawing operation is performed in which the cup's inside diameter = 80 mm and its height = 50 mm. Stock thickness = 3.0 mm, and blank diameter = 150 mm. Punch and die radii = 4 mm. Tensile strength = 400 MPa and yield strength = 180 MPa for this metal. Determine (a) drawing ratio (b) reduction, (c) drawing force, and (d) blankholder force? (Ctrl) I=
An automated blanking and forming line is designed to from 2 mm thick sheet, made from 2024 Aluminum, T4 temper, into a square sheet metal part. Elongation at 50mm 20% Young’s Modulus 70GPa Yield strength 325 MPa UTS 470 A) What is the force required to punch a square piece that is 500 mm on each edge? B) If the sheet blank was bent to a radius of 5 mm, what will be the radius after springback occurs? C) What is the required bend angle to achieve a 90° final bend angel for a bend radius of 5 mm?
Question: 2 a. Distinguish between roll bending and roll forming.b. What are some of the simple measures used to assess the feasibility of a proposed cup drawingoperation?c. Compare spinning over the press work for sheet metal products.d. Identify a major technical problem in tube bending.
Engineering drawing Find, top section, side section and front section?
A forging press plant must be planned to manufacture engine components as per the details given. Parts are placed in the furnace an hour prior to forging; they are then removed, forged, and trimmed one at a time. The complete cycle takes 3 min per part. Each time a new batch is started, the forging cell must be changed over, which consists of changing the forging and trimming dies for the next part style. This takes 4 hr on average. Applicable direct labor rate in that location is RM50 per hour, factory overhead rate on labor = 30%; capital investment in machine = RM750,000; rate of return = 10%; and applicable factory overhead rate on machine = 25%. The plant will operate 24 hr/day, 5 days/week, 50 weeks/year. Total output from the plant must be 800,000 forgings per year in batches of 1000 parts per batch. Assume scrap rate as 3%. i. For the above conditions, recommend the number of forging press cells that would be required for in the new plant. State reasons and assumptions if any,…
Name some products that can be manufactured by shape rolling and thread rolling
What is the working principles of Sheet Metal Rolling Machine?
What is the difference between plate and sheet material?
Name the four basic bulk deformation processes.