The joint between a diagonal and a chord in a timber truss is shown. The compressive force P in the diagonal is 20 kN. Determine the compressive stress in the diagonal, the bearing stress on plane ab, and the shear stress on plane ac. Both the chord and the diagonal are 150 mm by 150 mm (full nominal size) in cross-section. 40 mm Diagonal Chord a 160 mm

The joint between a diagonal and a chord in a timber truss is shown. The compressive force P in the diagonal is 20 kN. Determine the compressive stress in the diagonal, the bearing stress on plane ab, and the shear stress on plane ac. Both the chord and the diagonal are 150 mm by 150 mm (full nominal size) in cross-section. 40 mm Diagonal Chord a 160 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the maximum tensile and compressive bending stresses developed in the beam shown. The cross-section has the given properties. NA 1-35 x 10mm a. RA = b. RE= c. fb(c) = d. fb(T) = 80 mm 200 mm A 1.5m kN KN 5kN m MPa MPa B 1.5m SkN/m 2m 5KN n 2m 4
Determine the maximum tensile bending stresses in the beam shown. LetP= %3D 19 Note Answer in whole number I = 100 × 106 mm4 P kN/m 2. NA 130 mm 6 m B = 4P 200 mm 2P kN 6-X= Am 4P : - GP
For the truss shown, calculate the stress in area of each member BD. The cross-sectional member is 1200mm². 4m B 6m U 3m 4m E 3m 100KN 200KN F M FLSNI
1. The assembly is shown is attached to supports at A and D. Section BCD is a solid 2" diameter aluminum [E = 10,000 ksi] rod. Steel [E = 30,000 ksi] tube AB has an outer diameter of 3.50" and a wall thickness of 0.216 in. Determine (a) the stresses is sections AB, BC and CD, and (b) the deflections of joints B and C. [OAB = 3.40 ksi (C), Osc = 5.863 ksi (T) Oc, = 4.959 ksi (C), 8, = 0,0054"– , d. = 0,02975"→] %3D %3D %3D %3D 13 kips 17 kips A C 13 kips 17 kips 4 ft 5 ft 5 ft
For the truss shown, determine the safe value of P if the allowable stress in tension is 146 MPa in tension and 92 MPa in compression. The cross-sectional area of vertical and horizontal members is 1260 mm2 while that of diagonal members is 862 mm2 .
Determine the maximum magnitude of load P that can be applied to the truss. The maximum allowable tensile force in the members of the truss is (Ft) max = 5.2 kN, and the maximum allowable compressive force is (Fe) max = 3 kN. Take d = 2 m. (Figure 1) Figure 1 of 1 E d/2 C PV d/2 <
8 kN 4 m 15 kN 5 kN 2 m 2 kN 2 m 2 m A B с D E The aluminum rod shown has a diameter of 20 mm and is subject to axial forces acting at A, B, C, and D. Assume the rod has a Young's modulus of E = 70 GPa. a) State the internal axial forces within sections AB, BC, CD, and DE. Remember to indicate whether they are in tension or compression b) What is the displacement of A relative to C? c) What is the displacement of A relative to E?
The wood beam has a rectangular cross section in the proportion shown. The allowable bending stress iss =10 MPa. 500 N/m 1.5 b OB - x m 2 m 2 m Calculate the centroid of the cross section of the beam O (1.5b, 1.5b] O (1.5b/2), (1.5b/2)] O (0.(1.5b/2)] O (0,0) [(1.5b/2), 0] O (0, 1.5b)
Physics The following truss is subjected to a load of P = 31 kN at joint C. The pin at joint A has a diameter of 25 mm and is subjected to double shear. Determine the average shear stress developed in pin A of the truss. Im PRN Im Pin A a. In your Hard Copy, draw a FBD of the truss. b. What is the Resultant force at A? Aresultant = Number Units (Answer to 3 sig digs) c. What is the shear stress in A? TA = Number Units (Answer to 3 sig digs
A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm
The rigid beam is supported by the three suspended bars. Bars AD andCF is made of A-36 steel and BE is made of 2014-T6 aluminum alloyeach having a cross-sectional area of 450mm2. Determine the angle oftilt of the rigid beam DEF and the average normal stress in each bar ifthe rigid beam is subjected to the loadings shown. Take ESt = 200 GPa and EAl = 73.1 GPa.
*4-88. If the allowable normal stress for the bar is O allow = 120 MPa, determine the maximum axial force P that can be applied to the bar. %3D 5 mm 40 mm 20 mm P- r = 10 mm 20 mm