Prob. 2.13-8. A. thin, rectangular plate is subjected to a uni- form biaxial state of stress (,,a,). All other components of stress are zero. The initial dimensions of the plate are L = 4 in. and Ly = 2 in., but after the loading is applied, the dimen- sions are L = 4.00176 in., and L=2.00344 in. If it is known that σ₂ = 10 ksi and E= 10 x 10³ ksi, (a) what is the value of Poisson's ratio? (b) What is the value of σ,? O₂ = 10 ksl -X

Prob. 2.13-8. A. thin, rectangular plate is subjected to a uni- form biaxial state of stress (,,a,). All other components of stress are zero. The initial dimensions of the plate are L = 4 in. and Ly = 2 in., but after the loading is applied, the dimen- sions are L = 4.00176 in., and L=2.00344 in. If it is known that σ₂ = 10 ksi and E= 10 x 10³ ksi, (a) what is the value of Poisson's ratio? (b) What is the value of σ,? O₂ = 10 ksl -X

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

ox The state of stress at a given point in a material component is = 120 MPa; Oy = - 80 MPa and t = 60 MPa The loading on the component is increased so that stresses are increased to values which are k times the given values. Determine the maximum value of k if the material can withstand maximum normal and shear stresses of 300 MPa and 200 MPa respectively. 1 11
The strain of a component, which has a tensile modulus of 3 X 105 MPa, and subjected to a stress of 5000KPA, is .a 0.0000167 .b 0.0000176 .C 0.000167 .d 0.00176
A thin polymer plate PQR is deformed so that corner Q is displaced downward 0.9 mm to new position Q', as shown in. Determine the shear strain at Q' associated with the two edges (PQ and QR). Assume a = 150 mm, b = 216 mm, c = 180 mm, and A = 0.9 mm. a b P R C Answer: Shear strain y = Q i A X urad.
2.58 Knowing that a 0.02-in. gap exists when the temperature is 75°F, determine (a) the temperature at which the normal stress in the alu- minum bar will be equal to -11 ksi, (b) the corresponding exact length of the aluminum bar. 0.02 in. - 14 in. - Bronze A = 2.4 in² E = 15 x 106 psi a = 12 x 10-6/°F Fig. P2.58 and P2.59 18 in.. Aluminum A = 2.8 in² E = 10.6 x 106 psi a = 12.9 x 10-6/°F 300 mm 0.5 mm 250
The state of stress at a point is shown with respect to xy-plane. The state of stress at a point is shown with respect to x'y'-plane? 8 MPa y'v 60° S MPa +S MPa 10 MPa 8 MPa
1. At a temperature of 5°C, a 3-mm gap exists between the end of polymer bar (1) and support A as shown. Bar (1) is 50 mm wide and 20 mm thick (E = 800 MPa, a = 140 x 10-6/°C). Bar (2) is 75 mm wide and 25 mm thick (E = 2.7 GPa, a = 67 x 106/°C). The supports at A and C are rigid (i.e., fixed). Determine: a) the temperature at which the normal stress in bar (2) will be equal to -3.0 MPa, and b) the lengths of the two polymer bars at this temperature. (1) 3-mm gap 50 mm 500 mm B 75 mm 400 mm (2)
For a thin plate with no body forces, a plane state of stress exists where ay + bx²y – cx dy - e Txy = fxy + gx*y – h where a, b, c, d, e, f, g, and h are constants. What are the constraints on the con- stants such that the stress field satisfies both equilibrium and compatibility?
Read the question carefully and give me solution according to the question... Give me both solution
13
a. At a point in a given material the three dimensional state of stress is given by ox = oy oz = 10 MPa ,Txy F 20 MPa, Tyz = %3D !! TXZ = 10 MPa. Compute the principle planes if the corresponding principles stresses are, ol = 37.3 MPa, c2 = 10MPA, o3 =2.7 MPa %3D %3D b. , What no
Two polymer bars are connected to a rigid plate at B, as shown. Bar (1) has a cross-sectional area of 1.21 in.? and an elastic modulus of 2350 ksi. Bar (2) has a cross-sectional area of 1.032 in.? and an elastic modulus of 4100 ksi. Assume L1=20 in., L2=49 in., Q=7.1 kips, P=2.9 kips, and R=12.9 kips. Determine the horizontal deflection of end C relative to end A. P (1) (2) C В L1 L2 Answer: uc/A in. %3D