The internal resistance of a high voltage power supply is 24 MO and the output is set so that the potential difference across the output when on open circuit is 4000 V? When a load resistor R₁ is connected across the supply the voltage across R₁ is 3000 V. What is the value of the load resistor?

The internal resistance of a high voltage power supply is 24 MO and the output is set so that the potential difference across the output when on open circuit is 4000 V? When a load resistor R₁ is connected across the supply the voltage across R₁ is 3000 V. What is the value of the load resistor?

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

Physics
In RC Circuit, the current decreases exponentially with time as the capacitor charges. Explain the reason for this behavior.
R +1₁H sa In the circuit shown, the resistor has a value of 821 kohms and the capacitor has a value of 49.9 microfarads and the supply voltage is 24.0 volts. Given these values for this circuit, how long will it take for the capacitor to charge up to a voltage of 10.0 volts?
Three resistors are connected as shown to a battery. The value of the resistors are: R1 = 1.25KΩ R2 = 1.5kΩ and R3 = 3kΩ. The battery voltage is measured to be 45V. (i) What is the equivalent resistance for the circuit? (ii) What is the voltage drop over R2?
I'm trying to understand this figure Assume the capacitor in the circuit is initially uncharged. Can you calculate the current through each resistor right after the circuit is connected? If so, can you explain and show how you did it? What if the circuit has been connected and left alone for a long time. Calculate the charge on the capacitor plate
A student performs a lab where the voltagedrop across a resistor is measured as a functionof current. Plot a graph from the values givenin the following table, and determine theresistance of the circuit. Current, I (mA) Potential Difference, Current, I (mA)V (V)0.00 0.00200 9.00400 16.0600 24.0800 31.01000 40.0
can u explane
The figure below shows how a bleeder resistor (R = 246 kN) is used to discharge a capacitor (C = 63.7 µF) after an electronic device is shut off, allowing a person to work on the electronics with less risk of shock. Electronic circuit (a) What is the time constant? S (b) How long will it take to reduce the voltage on the capacitor to 0.100% of its full value once discharge begins? S (c) If the capacitor is charged to a voltage Vo through a 133 2 resistance, calculate the time it takes to rise to 0.865V, (this is about two time constants).
An accumulator with U1=150 V and negligible internal resistance is connected to a voltage divider as shown in the figure. a) How big will the voltage U2 be if no external load is connected? b) How large will U2 be if a load with resistance RL = 2250.0 Ω is connected between A and B? c) How large will U2 be if a load with resistance RL = 9000.0 Ω is connected between A and B? d) How big will the effect be in the load c)?
A resistor and a capacitor are connected in series to an ideal battery of constant terminal voltage. When the system reaches its steady state, what is the voltage across the resistor and the capacitor?
An ECG monitor must have a time constant less than 100 microsecond to be able to measure variations in voltage over small time intervals. If the resistance of the circuit (due mostly to that of the patient’s chest) is 1000 Ohms, what is the maximum capacitance of the circuit? Please submit your answer in units of nanoFarad (nF).
You have a circuit consisting of a power supply, switch, resistor, two capacitors, and voltage/current probes. The resistor has the value R1 = (1.8 ± 10%) MQ. The capacitors have %3D the values C1 = (0.6 ± 20%) µF and C2 = (2.2 ± 20%) µF. The logger pro data resembles the plot below. 40 35 30 25 20 15 10 1 2 3 5 6 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 a) Label the title and all the axes on the plot above. Identify which region corresponds to the capacitors charging and discharging. Be sure to include appropriate units (MKS).