The input impedance of a particular commercial true rms multimeter can be considered to be the parallel combination of a resistance of 10x106 n and a capacitance of 100 pF. The multimeter is being used to measure the output voltage of a transducer with a 50 kHz sinusoidal output voltage. The Thevenin equivalent voltage and impedance of the transducer, relative to its output terminals, are 1 volt (rms) and 23.85 ko respectively. The Thevenin impedance may be assumed to be purely resistive. Which one is the correct statement? Select one: O a. The reading of the voltmeter will be 0.80 V O b. The reading of the voltmeter will be 1.0 V O c. The reading of the voltmeter will be 0.60 V O d. The reading of the voltmeter will be 0.57 V

The input impedance of a particular commercial true rms multimeter can be considered to be the parallel combination of a resistance of 10x106 n and a capacitance of 100 pF. The multimeter is being used to measure the output voltage of a transducer with a 50 kHz sinusoidal output voltage. The Thevenin equivalent voltage and impedance of the transducer, relative to its output terminals, are 1 volt (rms) and 23.85 ko respectively. The Thevenin impedance may be assumed to be purely resistive. Which one is the correct statement? Select one: O a. The reading of the voltmeter will be 0.80 V O b. The reading of the voltmeter will be 1.0 V O c. The reading of the voltmeter will be 0.60 V O d. The reading of the voltmeter will be 0.57 V

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 7RQ: An RC series circuit is connected to a 120-V, 60-Hz power source. The resistor is 25 and has a...

See similar textbooks

Similar questions

An RC series circuit is connected to a 120-V, 60-Hz power source. The resistor is 25 and has a voltage drop of 65 volts. What is the capacitance of the capacitor?
For the following parts, identify the name of each circuit, plot the output waveform, and find the DC output average voltage. Part (a) V 1 cycle V₁ = V sin cor Part (b) PE Part (c) Vm Vi ele eeeeeeeeeeeeee D D₂ D₁ D₂ R Va + D₂ D₁
Determine the rms current in the figure for Vrms = 16 V and C = 74µF V f=10 kHz
Q/ Design a circuit to limit a 20 V rms sinusoidal voltage to a maximum positive amplitude of 10 V and a maximum negative amplitude of -5 V using a single 14 V dc voltage sour.
A step down converter is operated with a duty cycle of k = 0.75. The input voltage is Vs = 20V, and the load is: L = 5mH, R = 1502. The minimum inductor current is I₁ = 0.1A. The maximum inductor current is: Select one: a. 1.9 A b. None of these OC. 0.9 A O d. 1.1 A Oe. 2 A
Determine the waveform, theoretical, of the peak output voltage at Resistor L. 120 V rms 5:1 ooooo elele D₁ D3 D21 DA 4 R₁ WWW II Vout
A three phase full controlled converter is supplied by a phase voltage Vs-120V, 60 Hz. Consider a resistive load R=10 Q. If the RMS value of the output current is equal to 10.94A, then the RMS value of the input line current would be equal to: Select one: O a. 4.93A Ob. 2.93A OC. 6.93A O d. 8.93A TOSHIBA
C'uk Converter Design A C'uk converter has an input of 12 V and is to have an output of - 24 V supplying a 60 W load. Select the duty ratio, the switching frequency, the inductor sizes such that the change in inductor currents is no more than 12 percent of the average inductor current, the output ripple voltage is no more than 1.5 percent, and the ripple voltage across C1 is no more than 3 percent.
2. The circuit given below is using a transformer of 230V/30V. The load resistance is 10KS. Find Vin (rms and peak values), Vdiode and VLOAD (Peak and dc values). Draw the input and output voltage waveforms. (Si diode) Vin: Vin rms= Vin peak = VDIODE Vdiode = 4 Vin VLOAD: VLOAD Peak =. Load VLOAD VLOAD DC= 2031 Supply wwwwww
The peak to peak distance of a sinusoidal waveform displayed on a C.R.O. screen is 9 cm and the 'volts/cm' switch is on 25 V/cm. The peak voltage is given by O 2.78 V O 159.07 V O 112.50 V O 225.00 V
Electrical Engineering (25) It seems that a suburant in the negative impedance converter is the one that simulates negativity for a given floating impedance. Explain how the indicated subar- cuit operates.
Design a Cuk converter that has an input of 25V and the output of -30V. The load is 60W. Specify the duty ratio, switching frequency, inductor values and capacitor values. The maximum change in inductor currents must be 20 percent of the average currents. The ripple voltage across capacitor C1 must be less than 5 percent, and the output ripple voltage must be less than 1 percent.