The horizontal force F acts on the handle of the wrench (i.e Fis parallel to xy-plane). What is x-component of themoment of this force about the origin "O"? F = 19.5 N, a = 36 mm, b = 200 mm, c = 10 mm, 0 30°.ofB

When forces acting on any body then by applying the equilibrium condition in static will give us the…

Answered: The horizontal force F acts on the…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The 20-mm-diameter A-36 steel rod is subjected to the axial forces shown. Determine the displacement of end C with respect to the fixed support at A. 600 mm 400 mm 50 kN 40 kN B 50 kN
The uniform rectangular panel ABCD has a mass of 40 kg and is hinged at its corners A and B to the fixed vertical surface. A wire from E to D keeps edges BC and AD horizontal. Hinge A can support thrust along the hinge axis AB, whereas hinge B supports force normal to the hinge axis only. Find the tension T in the wire and the magnitude B of the force supported by hinge B. 2580 mm 1110 mm Answers: T = B = i B D 40° N N E
SITUATION 1. The quarter circular plate is subjected to forces asshown. If the plate weighs 50 kg, and assuming equilibrium.a. Determine the reaction ? in the ball-and-socket joint A.b. Determine the reaction ? in the roller at B.c. Determine the tension ? in the chord CD.
calculate the location of the centroid, the second moments and product of area for the cross- section if; D = 67 mm, B = 41 mm & t = 2.41 mm A L Test beam A Strain gauge W (a) Unsymmetrical cantilever beam with weight applied at the free end and at the "shear centre", so that there is no torsion induced. Section A-A Strain gauge 1 Strain gauge 2 b Strain gauge 3 a B (b) Location of Huggenberger strain gauges From these, calculate the orientation and position of neutral axis for pure bending in the vertical plane (i.e. bending about a horizontal axis).
The thin plate ABCD of mass 8 kg is held in the position shown by the wire BH and two links AE and DF. Neglecting the mass of the links, determine immediately after wire BH has been cut (a) the acceleration of the plate, (b) the force in each link. H. E 150 mm 30% A B F 200 mm 30 D. IC 500 mm
Q2. Member ABC is supported by two fixed supports at points A and C. The member has heights of 100mm at points A and C whereas the height is 600mm at point B. A point torque of 10KN.m is applied Im away from the point A. Determine the reactions at supports A and C. Write vour results in the box below. Use G-100GPA. B A T= 10 kN.m 100 mm 600 mm 1 m 1 m 2 m
The frame shown in the figure is supported by a hinge at A and a roller at E. Compute the horizontal and vertical components of the hinge forces at B and Cas they act upon member AC. (Positive Upward and to the Right) 240 lb D 3'
回の shear stress tmax in any of the three bars? P3 9 m P 135° up. (D 135° 90 dz s applied Knowing the steel the steel 09. A circular steel tube of length L = 0.90 m is loaded in torsion by torques T. s in the (a) If the inner radius of the tube is r, = 40 mm and the measured angle of twist between the ends is 0.5°, what is the shear strain y1 (in radians) at the inner surface? (b) If the maximum allowable shear strain is 0.0005 rad and the angle of twist is to be kept at 0.5° by adjusting the torque T, what is the maximum permissible outer radius (r2)max? B 12 mm is to be of ACR
Consider the simply supported beam shown below. L= 3m, w= 12kN/m, E= 180GPa, I = 140(10)^6 mm^4. Determine the following: A B |- -1 a. The maximum moment in the beam in kN-m b. The deflection at B in mm c. The location of maximum deflection measured from A in meters d. The maximum deflection of the beam in mm W C
The uniform beam is supported by two rods AB and CD that have cross-sectional areas of 12 mm? and 18 mm², respectively. Determine the force in bar CD in kN. ... D d 4kN/m A 5m ----
The flanged steel cantilever beam with riveted bracket is subjected to the couple and two forces shown, and their effect on the design of the attachment at A must be determined. Replace the two forces and couple by an equivalent couple M and resultant Rat A. The couple is positive if counterclockwise, negative if clockwise. 2.05 KN Answers: M= I R-1 1.25 m 690 N-m 0.44 m KN-m 1+ 67" 10.14 m 0.14 m 1.16 KN 1) KN
The symmetrical beam cross-section shown is loaded by a transverse shear force V 25 kip. Calculate the maximum transverse shear stress acting on the sec- tion. ΝΑ -+-1 in.|-- H V 6 in. 1 in. - 1 in.|-—_ 6 in.

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

The horizontal force F acts on the handle of the wrench (i.e F is parallel to xy-plane). What is x-component of the moment of this force about the origin "O"? F = 19.5 N, a = 36 mm, b = 200 mm, c = 10 mm, 0 = 30°. B