Q2. Member ABC is supported by two fixed supports at points A and C. The member has heights of 100mm at points A and C whereas the height is 600mm at point B. A point torque of 10kN.m is applied Im away from the point A. Determine the reactions at supports A and C. Write your results in the box below. Use G=100GPA. B T- 10 kN.m 100 mm 600 mm 1 m 1 m 2 m

Q2. Member ABC is supported by two fixed supports at points A and C. The member has heights of 100mm at points A and C whereas the height is 600mm at point B. A point torque of 10kN.m is applied Im away from the point A. Determine the reactions at supports A and C. Write your results in the box below. Use G=100GPA. B T- 10 kN.m 100 mm 600 mm 1 m 1 m 2 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The bridge truss shown carries the following uniform live load and concentrated live load. в с D A B E 3m K F G H J SO8m W(LL) P(LL) 15 110 Calculate the following: 7. Maximum force on member GH
RBH TRBV 3. The frame shown in the figure is hinged to rigid supports at A and E. find the components of the hinge forces at A and E and the forces in members BC and BD. RAH A REH TRAV E REV 120 D 5 0 ction
F ., É, are applied to the truss system. В a) Find member forces in each member and state if the members are in tension or 4 m compression. b) If the maximum force that any member can support is Tmax in tension and Cmax in compression, determine the maximum value of P that can be supported. A E 3 т 3 m 3 т 3 m F1 F2 F3 F4 F5 Tmax Cmax P 2P 40° 7 kN 8 kN 2P Note: Do not show zero forces in your calculations.
20kN/m P2=70 EN A=70° 1,5m um Im 1- Find the support reactions of the simple beam 2- Fnd internal equatrons and values force 3- Plot N vM draerams and elastic curve 7 moment L- Pind the location and value of max and Mn Moments
Q3. The truss shown below is fastened to E using a fastening strap. If the strap is to be considered as a support reaction, find the force in the strap. Next, determine the reactions at the other supports and forces in all members of the truss. The cross-sectional area of each member is as indicated. Use the value of E-210 kN/mm². A E (1000) 4m (800) (009) B (1000) (008) 3m D 100 KN 2m 4m FIGURE 03
回の shear stress tmax in any of the three bars? P3 9 m P 135° up. (D 135° 90 dz s applied Knowing the steel the steel 09. A circular steel tube of length L = 0.90 m is loaded in torsion by torques T. s in the (a) If the inner radius of the tube is r, = 40 mm and the measured angle of twist between the ends is 0.5°, what is the shear strain y1 (in radians) at the inner surface? (b) If the maximum allowable shear strain is 0.0005 rad and the angle of twist is to be kept at 0.5° by adjusting the torque T, what is the maximum permissible outer radius (r2)max? B 12 mm is to be of ACR
Given: Consider the truss shown below and the series of loading. 20 k Required: 8⁹ An 8⁹ 8⁹ 8' 8' a 10 k 8' (A) (A) Calculate the force in member bd for case (A) (B) Calculate the force in member bd for case (B) (C) Calculate the force in member bd using the principle of superposition for the truss loading below. DO NOT use equilibrium equations. 10 k d 5 k a 8⁹ 8' (B) b 8'
E oth ends of the steel shaft are attached to rigid supports. Find the distance a where the torque T must e applied so that the reactive torques at A and B are equal. 2 0.75d B T a A.
5. Bar ABD and bar CEF are connected using a pin at point C and a strut member BE to support a 9000 N load as shown below. Determine the reaction of strut member BE and determine the reaction of hinge at point F and the reaction of roller at point A. 2.5 m 2.5 m 3.5 m 1.5 m E D B C 4 m 2.5 m A F- 9000 N
Problem # 4. A 12-mm-diameter steel E 200 GPa] rod (2) is connected to a 30mm wide by 8 mm thick rectangular aluminum [E 70 GPa] bar (1), as shown. required to Determine the force P stretch the assembly 10.0 mm. Ans: = A (1) 0.45 m B (2) 1.30 m - C
The 20-mm-diameter A-36 steel rod is subjected to the axial forces shown. Determine the displacement of end C with respect to the fixed support at A. 600 mm 400 mm 50 kN 40 kN B 50 kN
The truss in the figure is loaded by four external forces as shown below. Knowing that P1= 3 kN, P2-4 kN, P3-6 kN and P4-2 kN, a= 2 m and h=2 m, you are required to: h A. P1 P2 E. НУ B a the supports A and E. P3 C a P4 F P1 E a) Determine the reactions at b) Using the method of joints, determine the forces of the members at joint c) Using the method of joints, determine the forces of the members at joint d) Using the method of sections, determine forces on members GF, GC, CD. e) Using the method of sections, determine forces on members GH, BG, BC. Note: You are required to draw the FBD and apply the equilibrium equations for each case.