4. The homogeneous cylinder of weight 150 N is placed on an inclined surface of negligible friction.The cylinder is prevented from moving by the vertical rod "BD", which is connected to thecenter of the cylinder by a rope. Assuming no sufficient friction between the bar and thecylinder. Determine the tensile force of the rope.150 NRopeDE45°frictionlessHinge40

Answered: Image /qna-images/answer/7eef643f-a6b5-4d99-a41e-75509bfb7133.jpg

Answered: The homogeneous cylinder of weight 150N…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For the given set up, the two cylinders on the left and right are movable horizontally, while the cylinder in the middle is fixed. Determine the distance a so that the system is in equilibrium and the tension T2 is equal to 2.5 N and T₁ is equal to 2.0 N. The radius of the three cylinders is equal to 20 mm, while the coefficient of friction between the cylinder and the rope (u) is 0.1529. T₁ T₂ a B
The bar shown is in equilibrium determine the forces P, T and R
Determine whether the block shown is in equilibrium, and find the magnitude and direction of the friction force when P= 150 N.
Determine the magnitude of the clamping forces (in pounds) exerted on the nut along line aa when two 78-lb forces are applied to the handles as shown. Assume that pins A and D slide freely in the slots in the jaws.
The bobcat loader (Figure Q3) has a mass of 1200-kg, shows the center of mass is at G1. If there is a 200-kg pebble in the bucket, with center of mass at G2 determine the reactions of each pair of wheels A and B on the ground and the force in the hydraulic cylinder CD and at the pin E. There is a similar linkage on each side of the loader. L0.5 m E 0.1 m_ D 0.2 m G2 0.18 m G1 0.6 m 0.5 m В 0.45 m 1.2 m 0.15 m 0.2 m 0.05 m Figure Q3
Members AC and AB support the 100-lb crate. Determine the tensile force developed in member (AB). 3 ft 4 ft 4 ft
A 200 lb rock is being lifted by a pry bar. Determine the force “P” required to lift the rock into the position show.
Determine the maximum downward force Pmax that can be applied to wedge A that will keep the assembly in equilibrium. Based on the value of the force in link BC, determine whether block C will slip or tip first. At Pmax, what are the frictional forces between wedge A and block B, fAB, and between wedge A and wall D, SAD? The weight of block C is 192 N while that of the wedge is negligible. Draw the FBDs of wedge A, block B, and block C. Label correctly all the forces (especially normal and frictional forces with proper subscripts) and indicate the direction of the impending motion next to each FBD. Note that the weight of block B, though not negligible, is not necessary in the computation. W HAD 0.27 D P A B 60° HAB= 0.14 |sg =0 E C 1 m HCF = 0.375 F R 2.4 m 3.2 m
A mechanic is reinstalling a newly-sharpened blade on a lawn mower. A wedged-in block of wood at C prevents the blade from rotating as the 34-lb force is applied to the wrench handle. The blade is bolted to a bracket attached to the motor shaft O, which protrudes through the bracket and blade. Determine the normal force at C. State any assumptions. Does it matter whether the bolt at B is installed? 6.9" 34 lb Answer: Nc= i 2.02.0" OoOB -9" C lb
Could you go step by step on how to solve this problem. I've been tackling it for the past few hours and I can't seem to get it quite right.
As shown, the truss is loaded by the forces P = 210 lb and P = 401 lb and has the dimension a = 3.30 ft L. P, Using the method of joints, determine FAR. FRG, and Frp, the magnitude of the force in each of the members connected to joint B. Assume for your calculations that each member is in tension, and include in your response the sign of each force that you obtain by applying this assumption. Express your answers numerically in pounds to three significant figures separated by commas. • View Available Hint(s) Hνα ΑΣφ vec FAB, FBC, FBD = lb

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS