The holes are for 12 mm diameter bolts. Determine the total service load capacity if the live load is three times the dead load. The location of the centroid is 21.25 mm from the outer face of the web. a. Use LRFD. 100 100 100 100 b. Use ASD. Properties of C250 x 29.75 Ag = 2036 mm? 62.5 bf = 50 mm d = 250 mm tw = 6 mm tf = 6 mm 62.5

The holes are for 12 mm diameter bolts. Determine the total service load capacity if the live load is three times the dead load. The location of the centroid is 21.25 mm from the outer face of the web. a. Use LRFD. 100 100 100 100 b. Use ASD. Properties of C250 x 29.75 Ag = 2036 mm? 62.5 bf = 50 mm d = 250 mm tw = 6 mm tf = 6 mm 62.5

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.12.3P

See similar textbooks

Similar questions

Considering the following steel connection. The plates in Pink are 9mm steel plates. The middle plate (Yellow) is 18mm thick. The width of the plate is 100mm. The maximum allowable tension stresses on any of the plates is 100Mpa in Gross Area Yielding and 150 Mpa for Net Area or Tension Rupture. The bolts used are 8mm in diameter, the holes are 10mm in diameter, no need to add 1.6mm. The bolts allow a maximum of 280 Mpa of shear. Determine the maximum allowable "P" of the connection in kN.
Material Strengths: Fy = 248 MPa, F = 400 MPa For the two lines of bolt holes, the pitch is the value that will give a net area DEFG equal to the one along ABC. The diameter of the holes is 22 mm. The thickness of the plate is 12 mm. Determine the LRFD design tensile strength based on yielding on gross area. D A to 50 1 ÓB 50 50 ic O 410 kN O 464 kN O 446 kN O 401 KN F IG Pitch Pitch KISS|Y
4. An UPE 300 is to be used as a tension member and it is bolted to a 10mm thick gusset plate with bearing type 8-M20 8.8 bolts as shown in the figure below. a. Check all spacing and edge distance requirements. b. Compute the allowable tensile strength of the channel UPE 300. Don't consider shear strength of the bolts and bearing strength of the bolt holes. [all dimensions are in mm] Material both for gusset plate and UPE 300: S275 F-275N/mm² Fu=430N/mm² UPE 300 Ag = 5660 mm² tw 9.5 mm x = 28.9 mm 70 160 70 + 10mm thick gusset plate +50+ 80 -80-80-50 o +50+80 -80 80-50 UPE 300
A992 steel is used for the tension member shown. The bolts are ¾ inch in diameter. The connection is to a ⅜ inch thick gusset plate. A. Determine the nominal strength based on the gross area. B. Determine the nominal strength based on the effective net area.
Check the bolted section of the given gusset plate connection assuming that the connection is done by M12 bolts with a staggered arrangement. The maximum design tensile axial force to be sustained is Ned = 168 kN. Assume a grade of S235 steel. P. Gusset plate BỘ do=13mm Gusset plate O DO t=16mm t-16mm1 Ni.Ed FO NtEd do=13mm do3D13mm G. 40mm 40mm 140 mm 240mm 30mm
A double-channel shape, 2C8 x 18.75 is used as a tension member. The channels are bolted to a ¾-inch gusset plate with % - inch diameter bolts. The tension member is A572 grade 50 steel and the gusset plate is A36. If LRFD is used, how much factored tensile load can be applied? Consider all limit states. →2" popoy |-|-|-|-|-| n оо- 0 0 0 0 x + = ³/8" 288×18.15
The tension member shown in the figure below is a ¹/2 x 10 plate of A36 steel: Fy = 36 ksi, Fu = 58 ksi. The connection is with 9/8-inch-diameter bolts. -→| 20 |einetein | 21 | 6 spaces @2" t = 1/2 in. Compute the nominal strength based on the net section. (Express your answer to three significant figures.) P₁ = kips
1.A tension member is 25 mm thick plate as shown. The bolts are 20 mm. diameter high-strength bolts. The steel is A36. Compute the following: 130 mm 25 mm 0 0 a) The design strength for LFRD. b) The allowable strength for ASD. 25 mm CIVIL ENGINEERING STEEL DESIGN
Determine the LRFD design strength and the ASD allowable strength. Neglect block shear. A36 steel and 7/8-in Ø bolts N VA N SZ 2-MC 12 x 40 00 K All 2 in 2 in 3-in 3/in 2/in
The tension member shown is a PL 5/8 x 10, and the steel is A36. The bolts are 7/8-inch in diameter. a. Determine the design strength for LRFD. b. Determine the allowable strength for ASD. Tühitinin 2" 2" + 32 | 3² | O O O O OO O
A Channel C6x13 is used as a tension member. The holes are for 5/8 inch in diameter of bolts. Using A36 steel with Fy=36 ksi and Fu=58 ksi. The gross area of C6x13 is 3.81 in? and Assume U =0.85 Using LRFD what is the design strength based on Tensile Rupture/Fracture 4 @ 2" a 1 1/2 Ob 3" Oc 1 1/2 " I d e C6 x 13 Round your answer to 3 decimal places.
Determine the allowable tensile force P which can be appllied to the plates shown. The AISC specifications A36 steel and 20 mm diameter A325 bolts placed in standard holes with threads excluded from the shear plane are used in a bearing in a bearing type connection. Fy = 248 MPa, Fu = 400 MPa, Fv = 206.9 MPa and Fp = 1.5 Fu. P P CIVIZ 12mm 250 mm ENGINEERING - STEEL DESIGN 12mm P P