The following instruction is executed. Assume that before execution, register R15 contains 0x18, and the flags are ZF=0, SF=1, and CF=1. Ox indicates hexadecimal; do not include a Ox with your answer. Instruction: CMP R15, Ox21 After execution, register R15 contains (in Hex) and the flags will be ZF= SF= and CF=

Q: Question 4 The ARM allows any instruction, including branches to be executed conditionally. O True O…

A: Introduction: The Arm processor was created by Acorn Computers in the 1980s. Up until recently, the…

Q: In the following instruction sequence, show the value of AL for each line of code. Write the value…

A: Instructions Value of AL(H) MOV AL, 01100001B AND AL, 00011101B 1H MOV AL, 12H MOV AL,…

Q: LOAD R, (600)

A: In this addressing mode, The address field of the instruction refers to a CPU register that…

Q: An instruction is given as: ADD Ax, Bx. Identify and explain the two key sections of the…

A: Microprocessor or microcontroller are programmed with something called as assemble language. This is…

Q: AND BX with DX and save the result in BX b) AND 0AEH with DH

A:

Q: Which of the following instructions JMP, CMP, JZ, and JNZ can transfer control to another point in a…

A: Ans : The following instructions JMP, CMP, JZ and JNZ in this that can transfer control to another…

Q: Q3/ Initially assume all flags are set, find the values of status flags and AL after each…

A: Status Flags: Bits in a register indicating results or status of arithmetic/logical operations.AL…

Q: Write the instruction to add the carry flag to AH register. You must write only one instruction.…

A: The instruction is:

Q: 14. A subroutine was called using a conditional branch (BR) instruction. The subroutine ends, as…

A: About BR instruction:…

Q: Which assignment statement would be implemented by the following machine instructions LD  R1, b LD…

A: Here is the explanation regarding the assignment statement for the given statement.

Q: A, B and C are in XO, X1, X2; and A-6, B=3, C-9. ZERO is a special register holding the value of O.…

A: In this question we have to find the final value in X2 after executing the assembly code Let's find…

Q: what operation is performed when the instruction "LXI H, 9001H" is executed?

A: Given instruction is LXI H, 9001H  In 8085 microprocessor, there are seven internal data…

Q: The following program is stored in the memory unit of the basic computer. Show the contents of the…

A: Step 1: To analyze and demonstrate how the program progresses through its execution on a basic…

Q: Q4- What is the result of each instruction of the following program and its effect on flag register?…

A: Given:A = 4E (in hexadecimal)D = 20 (in hexadecimal)MVI A, 4E: Moves the immediate value 4E into…

Q: NAME THE INSTRUCTION ONLY that will perform the following function (i.e. ADD,MOV,SUB...etc.) NOTE:…

A: The answer is ADC (Addition with carry)

Q: efore EACH of the following statements execute assume that register A contains 19AC and register X…

A: The provided statements describe the step-by-step execution of a computer program or assembly…

Q: What will be the contents of BX after the following instructions execute?mov bx,5stcmov ax,60hadc…

A: Given: mov bx,5 stc mov ax,60h adc bx,ax the contents of BX register is 0110 0110b=0066h

Q: 5. For the instructions that execute one after the other, give the states of the Hags and the…

A: Here is the complete solution of the above problem. See below steps.

Q: If a read-loop is written to process an unknown number of values using the while construct, and if…

A: Answer: To receive an unknown number of values from a file and get their sum, use the algorithm…

Q: 2. Write an algorithm by using a proper control instruction to calculate y(x)! equation -2x x≥0 y(x)…

A: Here is the algorithm based on the the conditions above.

Q: Exercise 1: Write a program to perform logical AND operation between any data in register A and…

A: as per bartleby policy we are allowd to only solve 3 question when multiple questions are uploaded.…

Q: For questions 6 through 10, state whether the statements are True or False (Do not provide any…

A: 6. After the LMC instruction 333, the original number in the calculator is unchanged - TRUE

Q: Which of the following is true with respect to the LC-3 Control Unit? O The Instruction Pointer is…

A: The LC-3 (Little Computer 3) stands as an instructive computer architecture, purposefully designed…

Q: What happens to the rest of the code when the RET instruction is omitted from a procedure?

A: Instruction: Instructions for CALL and RET. The use of assembly-language operations is controlled…

Q: The destination operand of the IMUL instruction cannot be a memory operand. True False

A: Ans) IMUL instruction is used for signed multiplication of two operand.

Q: 2. Determine the C, Z, V, S, N flags of the status after the following instructions: 1) LDI R18, 25…

A: Dear Student, LDI is used to store a 8-bit constant in registers starting from 16 up to 31 it does…

Q: 12- Write a program to count from 0 to 15D using LOOP instruction.

A:

Q: "Given the initial statuses of FLAGS -- OF = 0; ZF=1; AF=0; PF=1 and CF=0 and that AL=1F and BL=F1.…

A: Flag:- The flag is defined as a special purpose flag.

Q: The LFSR needs to be written as function and the main function should call the LFSR function using…

A: We have to write a function in MIPS Assembly Language that computes the next state of a linear…

Q: The execution of the RET instruction causes the continue of the execution of the main program…

A:

Q: Q1: If DX contains 81FEH and CX contains 1986H, explain the effect of the following instructions on…

A: i)  SUB DX, CX

Q: Which of the following instructions JMP, CMP, JZ, and JNZ can transfer control to another point in a…

A: Question about JMP, CMP, JZ AND JNZ

Q: The "popl" instruction will set the processors condition codes (i.e., ZF, CF, SF, and OF).…

A: The objective of the question is to determine whether the 'popl' instruction in assembly language…

Q: Assume AL=23h; CL=05. Write the content of AL after ROL AL, CL- showing the calculation steps.…

A: STC instruction will set the carry flag initially.

Q: What may possible trigger a return to the instruction presently being performed in the case of an…

A: It is a collection of instructions that constitutes the programmed that will be run: An expression…

Q: OI AL and register after execution of the program MOV AL, FFh MOV BL, AL TEST AL, BLH SUB BL,0FH HLT…

A: Here is the explanation.

Q: An example of a control instruction is? a. MOVE O b. LOAD O c. JUMP O d. ADD

A: Program Control Instructions are the machine code that are utilized by machine or in low level…