The following data pertaih to a sandstone formation((a 0.81, m 2): formation thickness -15 ft; formation wateralinity =140,000 ppnh, saturation exponert, n-2, and formation temperature 180°F The vertical resistivity profile of the formation is shown by the following figure. R,, ohm.m 10 20

Q: Can you add the datum line in the illustration and make a bettter illustration based on solution

A: Given, Angle made by nozzle = 45o Horizontal distance = 15 to 20 m

Q: Determine the ỹ coordinate. y b. = ky? a

A:

Q: For the given structures, determine the degree of indeterminacy. 7. A 7

A:

Q: Locate the centroid 10 mm 20 mm 10 mm 10 mm 20 mm 50 mm y

A:

Q: 6 in Gin Gin 9 in 3in

A: Schematic diagram of the given problem:

Q: Fo B - P 800 mm C -600 mm

A:

Q: For the given structures, determine the degree of indeterminacy. 8. 8

A: Solution : The number of external reactions ( r ) = 9  The number of members ( n ) = 2  These values…

Q: 7⁄8 inch+  5⁄32 inch

A:

Q: y 500 50 80 -140- - 140- 80 60 400 500 50 500

A: Given- plate area is given  To find- centroid of given plate area

Q: X 0.75 3 -3.5 1.5 1.5

A:

Q: 1⁄6 yard +3⁄8 yard

A:

Q: 05 Find the XT 0.5 1.5 3 2.5

A:

Q: Find the domains of: f(x)=- x - 9 a. {x\x€R, x#9} b. {x|x€R, x#-3, x#3} c. {x|x€R, x+-3, x # 3, x #…

A: Hello dear this is the solution of your problem The answer is found to be Option (b)  For…

Q: a) top most, hef tmost

A: X = 1.5 cm Y = 5.48 cm

Q: 31⁄5 / 4⁄7

A: 31/5=6.2 4/7=0.571

Q: hat about pin d?

A: We know that Forces acting at Joint D are shown in figure below Forces moving away from joints are…

Q: Explain any fiften (15) AUTOCAD commands used in drawing

A: Autocad is a computer based drawing software which is in the field of civil engineering to prepare…

Q: For the following items, answer whether the multiview projection matches the isometric drawing depic…

A: The given figure shows the different items, it is required to state whether the Multiview projection…

Q: +y") dx ly

A:

Q: 38 O 18 22 66 102 The known: front projection, side projection Required: Draw the three projections…

A:

Q: The column section shown above is reinforced with equal number of 20 mm bars с 1. on each face.…

A: Answer  1) Calculation of neutral axis 'c' We know that at balanced condition strain at extreme…

Q: where did 3sqrt of 2 came from?

A: Given, A structure with carrying varying load   To find : Where 32 came from.

Q: For the given structures, determine the degree of indeterminacy. 3. 3

A: The given structure has two fixed supports at ends and one roller support in the middle. The fixed…

Q: The 4th root of 81

A: Answer : 3

Q: The block of mass m1 = m0 is attached to a spring of elastic constant k = (m0g)/H and natural length…

A:

Q: There are 7 dimension commands in AutoCAD. True False

A: These are the dimension commands available in AutoCAD:

Types of Composite

Composite materials are formed by merging two components that have different chemical and physical properties. The merged output is termed as a composite, whose properties are completely different from the individual components. Composite materials also have better strength than the individual components.Composite materials usually have two main parts, reinforcement material, and matrix material. The matrix material acts as a binder and surrounds the fiber of another material that bears a much higher strength. This material is known as the reinforcement material. The matrix materials are usually high-strength additives resins, while the fibers of the reinforced material can be random, oriented, and in a mat format.Composite materials are also known as fiber-reinforced composite polymers because they are composed of the polymer matrix which is reinforced to laboratory-created fibers or naturally occurring fibers, such as glass fibers, carbon fibers, or aramid fibers. Under the application of external loads, the matrix material absorbs and transfers the loads to the fibers, these fibers in return provide good compressive strength, tensile strength, and stiffness to the fiber-reinforced composite materials.Depending upon the matrix and the reinforcement material, different properties can be induced to the fiber-reinforced composite materials, including good corrosion resistance properties. The most common matrix material is the resin while the glass fibers act as the reinforcement material. Strong fibers provide strength and stiffness to the composite materials while, a soft and flexible resin provides shape to the composite materials.