ver. 1.0The following block diagram is for an Armstrong indirect FM transmitter.Find the missing five values (n1, f2, Af, n2fc) . Show your stepsf%=D200 kHz - 12.8 MHz f. 1.875 MHz f-A/= 24.4 HzMHz/= 75 kHz%3DA=1.56 kHz A=kHzfaCrystalOscr.NarrowbandPMFreq.multiplierFreq.multiplier RF amplifierMixer200 kHz8(1) = [fc)dtSerIntegratorCrystal oscr.MHzActivat

Given : Brief description: The question they have mentioned Armstrong indirect FM transmitter.…

The following block diagram is for an Armstrong indirect FM transmitter. Find the missing five values (n1,fe2, Af, n2f) . Show your steps fe=200 kHz f=12.8 MHz f.- 1.875 MHz f.- Af= 24.4 Hz MHz kHz Af=75 kHz %3D %3D Af= 1.56 kHz Af Crystal 200 kHz Narrowband РМ Freq. multiplier Mixer Xn Freq. multiplier RF amplifier Xn2 OScr. g(1) = [f(t)dt fer %3D Integrator Crystal oscr. MHz f()

The following block diagram is for an Armstrong indirect FM transmitter. Find the missing five values (n1,fe2, Af, n2f) . Show your steps fe=200 kHz f=12.8 MHz f.- 1.875 MHz f.- Af= 24.4 Hz MHz kHz Af=75 kHz %3D %3D Af= 1.56 kHz Af Crystal 200 kHz Narrowband РМ Freq. multiplier Mixer Xn Freq. multiplier RF amplifier Xn2 OScr. g(1) = [f(t)dt fer %3D Integrator Crystal oscr. MHz f()

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Figure (1) shows the block diagram of a wideband frequency modulator using the indirect method. This modulator is used to transmit audio signals containing frequencies in the range of 100 Hz to 15 kHz. The narrowband is supplied with a carrier of frequency fl-0.1 MHz by crystal- controlled oscillator also ß-0.2, a second crystal- controlled oscillator supplied a sinusoidal wave of frequency 9.5 MHz to the mixer. The system Carrier frequency at the transmitter output, fc-100MHz Minimum frequency deviation, Af-75, find nl and n2? f(t) NBFM Freq. Multiplier 1 Oscillator1 Fig. (1) Mixer Oscillator2 Freq. Multiplier 2 frm(t) n1=72, n2=47 O n1=73, n2-48 O n1=75, n2=50 n1=77, n2=52 O n1=76, n2=51 O
In an Amplitude Modulator where the carrier and modulating signals are both sine waves, the frequency spectrum of the resulting AM signal is shown below. 12V 2V 2V kHz 803 808.6 a) Determine the equation of the modulating signal b) Calculate the bandwidth of the AM signal c) Calculate the effective current of the AM signal thru a 75-ohm load. d) Sketch the AM wave and label the maximum and minimum voltage of the signal.
in FM , the maximum allowable frequency deviation is 4kHz and the frequency deviation by noise is 156.42HZ? then the signal to noise ratio is .......
Derive the frequency reuse factor for a triangular cell
12- A DVM measure... a- peak value. b- RMS value. Average value. d- peak to peak value. 13 The study of energy distribution across the frequency spectrum of a given electrical signal is done by a Distortion meter b-wave analyzer.
2. Write an OCTAVE program to plot the signal given below. P- Pmax Sin(21Ift); where Pmax= 10 MW, -60 Hz. %3D Find out time period and verify it with graph. Assume necessary data.
Draw the diagram of a halfwave power supply circuit and a fullwave supply circuit. Aside from the difference between the number of diode utilized in both circuits, state the main advantage of the fullwave power against the halfwave circuit for the following scenario . When there is a defective diode (open anode- cathode ) When the filter capacitor is defective (capacitor is open)
Determine the modulation index for a PM modulator with a deviation sensitivity of kp= 1.7 rad/V and a modulating signal of vm(t) = 7cos (2π3000t). A phase modulator has kp= 2.8rad/V. What rms voltage of a sine wave causes a peak phase deviation of 74°? Determine the peak phase deviation for a PM modulator with deviation sensitivity K = 3.8 rad/V and a modulating signal vm= 12 sin(2π1000t).
Q2. An angle modulated signal with a sinusoidal carrier 100 cos Znfat and a sinusoidal message with frequency fa-20 Hz, knowing that -0.7, a) Draw the single sided spectrum b) Determine the modulated signal bandwidth. c) Determine the 70% and 90% bandwidth and transınitted power.
How it is generated Single Sideband Modulator Using Filter Method
Q2: A modulating signal is used to modulate a carrier signal(AM modulation). Let Pr . Pc. PSB. PuSB. PLSB and u are the total power, carrier power, side band power, upper side band power, lower side band power and modulation index respectively. Prove the following: a. Pc = Pr () c. Pusn = Pisn =) Pr m2 b. Psn = Pr %3D 2+m2 LSB 2+m? (2+m2
An AM signal with a 40 V modulating signal and a carrier voltage of 50 V. What is the peak voltage of the upper side frequency?