The following are the true bearings of a closed traverse. Compute the interior angles of each side. BEARINGS LINE 1-2 N 50° 20' E S 42° 27' E S 45° 17' W N 28° 52' W N 35° 50' W 2-3 3-4 4-5 5-1

Q: 12 F2-10. If the resultant force acting on the bracket is to be 750 N directed along the positive x…

A:

Q: 16. Given the following sketch and tabulated data a 1osed traverse in which the bearings of side CD…

A: For the given question we have to convert all bearings in to WCB system so as to calculate latitude…

Q: Determine the internal shear in kip at the distance 14 ft. from point A (it is the point between…

A:

Q: --- Thanks for answering in advance ---

A: Step 1:Step 2:Step 3:Step 4:

Q: Determine the nominal moment strength of the irregular beam shown. fc' = 21 MPa and fy = 413.70 MPa.…

A:

Q: † weightleso $ homageneous bar ABe is being suppor ted by a 5-mm diameter cabes AD and AB Delermine…

A:

Q: Q3) For the circular arch shown in the figure, compute the value of "P" such that the vertical…

A:

Q: SLIDES 7-12: 30EI

A:

Q: Q4: A/ Defined (W.C.B) direction, then compare it with (R.B) direction. B/ In closed traverse ABCD…

A: A. WCB and RB Whole circle bearing (WCB) is a type of direction used in land surveying,…

Q: 3 mm (thickness) by 50mm (depth) rectangle machine component is supported by A pin at Z and a 2.5cm…

A:

Q: A movable bracket is held at rest by a cable attached at Eand by frictionless rollers. Assume that…

A:

Q: Problem 4.8 - The end of pole AD is buried deep in the ground. The tensions in cables BE and CF are…

A:

Q: Determine the moment of the 60-lb force about the point O of contact between the prybar and the…

A:

Q: What distance should a 2N load placed from the pivot so that the see saw won't move? 0.3 m ? m 3N O…

A:

Q: Construct influence lines and determine ordinates and slopes for given reactions, shears, and…

A:

Q: Ex! 2 Design a round spiral Glumn to support on axial dead lod Polof 1090KN and an oxial live load…

A: Spiral column reinforcement : Diameter : i) 14*ϕLL ii) 6 mm Take maximum of above  ϕLL is the…

Q: The homogeneous 120kg wooden beam is suspended from ropes at A and B. A power wrench applies the…

A:

Q: d W.S. 22.5KN 60⁰ pulley 5m hinged (Width normal to paper -2.8m)

A:

Q: 100 kN Find the horizontal base reactions for the portal frame shown, when the vertical bars have A…

A:

Q: 3:2KN 2.om 2.0m %23 1.5m 1.5m 1.5m 1.5m

A:

Q: P6-2. Draw the free-body diagrams of the boom ABCD and the stick EDFGH of the backhoe. The weights…

A:

Q: C16-2. The crank AB turns counterclockwise at a constant rate w causing the connecting arm CD and…

A: Angular velocity of crank AB = w

Q: Student Portal : FEU.. EG8245H5 Das Google M Inbox (258) - 20191... Mga Klase ? Student Login…

A:

Q: 103 H.W :- the simply supported beam shown below carries the factored louded indicated. Using f'c =…

A:

Q: Quo: Find the moment at Co) to hold the gate, shownin figure belouy closed. Negleet gate weight.…

A: pressure on the gatep=wAxhere.w=9.81KN/m3area of the gateA=width×length widthb=1.8mfrom the…

Q: 12 F2-10. If the resultant force acting on the bracket is to be 750 N directed along the positive x…

A:

Q: Find the moment (N-m) about point O Each square is Im. on each side. F1 -63N F2-82 N - 55N C 122 N…

A:

Q: Mlx y = 6EI (17) MI at x 93 EI at the center 16EI

A:

Q: F16-7. If roller A moves to the right with a constant velocity of vA the link and the velocity of…

A: Given:- The constant velocity of the roller A = vA = 3 m/s The length of the link AB = 1.5 m To…

Q: draw shear and moment diagram

A:

Q: P Zm X B 4m TR₁ Draw the shear and

A:

Q: At what distance, "a" should the bearing supports at A and B be placed so that the displacement at…

A:

Q: Problem Set 8 • Derive the following equation of maximum deflection using double integration method.…

A:

Q: For the propped beam shown determine the folicwing Max deflect'on Маx shear Maxirmum mornent 5kN/m…

A:

Q: A “scale” is constructed with a 4-ft-long cord andthe 10-lb block D. The cord is fixed to a pin at A…

A: The given figure is shown below:

Q: For the frame loaded as shown, draw the complete and correct FBDs of the following: whole frame,…

A:

Q: Draw the shear and moment curves label the maximum value of the moment Given: SN = 83 Maximum Shear…

A:

Q: draw shear and moment diagram

A: Given:Required:Shear force and bending moment diagram

Q: Replace the loading acting on the post by a resultant force, and specify where its line of action…

A: Given:Required:Resultant force and it's location from B on AB

Q: H.W: determine the magnitude of the resultant and the direction measured from the horizontal line. 8…

A: Direction Of force FA  is not given Assume Direction of force FA  from vertical is 50°Then foce on…

Q: 2/75 If the resultant of the loads shown passes through point B, determine the equivalent…

A: - In y direction : Ry = -10 + 4 - 12 = -18 kips - In x direction : Rx = 0 - Moment at point O : Mo =…

Q: From the given closed, adjust the bearing assume that the error is the for each anghe. Line 1-2 2-3…

A: Given: LINE REDUCED BEARING  WHOLE CIRCLE BEARING (WCB) 1-2 N 45° E 45° 2-1 S 45° 20' W 225°…

Q: The steel shaft DF consists of three concentr nooth bearings at D and E. It is coupled to 14 kW of…

A: We have to calculate shear stress for BC & CE. Shear stress - it is force per unit area that is…

Area Computations

The area is the mathematical estimation of the inner space occupied by any shape or object and area computation is the evaluation of how much inner space that particular shape or object has utilized. Simple applications include calculating the area of wall for the quantity of paint or plaster to be applied on it, area calculations for construction of a trapezoidal dam and how much material is required, calculating the area of a circle to determine the range or distance of wheels that they are capable of covering due to varied radii and so on.