Q2 = 10 liter/sDI =?WaterD3 = 65mmTank base area=1 m²rigure 5(b) A water reservoir (p = 998 kg/m³ ) is being filled through section 1 at Vị = 3 m/s andthrough section 2 at Q. = 10 litre/s and exit at section 3 at 6.5 m/s which is shown inFigure 5. Calculate the diameter at section 1 so that :i.h is constant,ii.h decrease at 6 mm/sh is constant and section 2 is closediii.of

In the tank, some pipes are inlets and some are outlets. From inlet the water enters within the tank…

Answered: 2 Q2 = 10 liter/s %3D 3 DI =? Water D3…

Engineering

Mechanical Engineering

2 Q2 = 10 liter/s %3D 3 DI =? Water D3 = 65mm Tank base area=1 m²

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water flows inside a solid cylindrical pipe, which narrows as it goes up to a height h (see diagram below). The lower horizontal section has circular cross-sectional diameter d, whereas the upper horizontal section has diameter d/2. Let us denote A to be a point at the lower horizontal section and B to be a point at the upper horizontal section. The flow speed at A and B is uд and u, respectively. The pressure at A and B is PA and PB, respectively. РА UA Oom Ja d d/21 1 UB h (a) Assuming water to be incompressible, show that the flow speed at B is four times the flow speed at A. (b) Use Bernoulli's equation to find the drop in the water pressure from A to B. Express the result in terms of h, uд, the density of water p, and the acceleration of gravity g. (c) Above certain critical height h, vapour bubbles start to appear at the top horizontal section, which hinders water flow through the pipe. Explain why this happens.
4. A centrifugal pump delivers water to a height of 22 metres at a speed of 800 r.p.m. The velocity of flow is constant at a speed of 2-0 m/s and the outlet vane anglc is 45°. If the pump discharges 225 litres of water per second, find the diameter of the impeller and width of the impcller at oudet. (Ans. 375 mm: 95 mm)
The figure below shows a gasoline storage tank with cross-sectional area Asub1, filled to a depth h. The space above the gasoline contains air at pressure psub0, and the gasoline flows out the bottom of the tank through a short pipe with cross-sectional area Asub2. Derive expressions for the flow speed in the pipe and the volume flow rate. Thank you!
Q1) Using a system similar to that shown in figure, if air pressure p = 50 kPa., and the depth h1 = 0.3 m, compute the water flow from side nozzle of diameter (d = 10 mm) and the rise h₂ from that nozzle. vesn Air pressure It, 11₂ Nozzle
SUPPLEMENTARY QUESTION The figure shows two reservoirs connected by a pipe. The discharge rate in the pipe is known to be equal to SN/100 (m2/s) (where SN is the sum of your student number). Calculate the height of the second reservoir (H2), and the pressure head, velocity head and elevation head at point 3 (mid-point of the pipe). HI 300 m H2 datum A = SN/1000 L = 100 x SN (m) D 0.3 m Please solve these question my sn number 31
The water of a 14’ × 48’ metal frame pool can drain from the pool through an opening at the side of the pool. The opening is about h = 1.05 m below the water level. The capacity of the pool is V = 3740 gallons, the pool can be drained in t = 10.2 mins. P0 is the pressure of the atmosphere. ρ is the density of the water. a. Write the Bernoulli’s equation of the water at the top of the pool in terms of P0, ρ, h. Assuming the opening is the origin. b. Write the Bernoulli’s equation of the water at the opening of the pool in terms of P0, ρ, h and v, where v is the speed at which the water leaves the opening. Assuming the opening is the origin. c. Express v2 in terms of g and h. d. Calculate the numerical value of v in meters per second. e. Express the flow rate of the water in terms of V and t. f. Express the cross-sectional area of the opening, A, in terms of V, v and t. g. Calculate the numerical value of A in cm2
The plunger diameter of a single-acting reciprocating pump is 115 mm and the stroke is 230 mm. The suction pipe is 90 mm in diameter and 4.2 m long. If cavitation takes place at the suction head of 4 m, the barometer stands at 10.3 m of water, and the water level in the sump is 3 m below the pump cylinder axis. 3.1 Find the maximum allowable speed to operate the pump 3.2 What power is expected in overcoming friction at this speed, takef = 0.01
The plunger diameter of a single-acting reciprocating pump is 115 mm and the stroke is 230 mm. The suction pipe is 90 mm in diameter and 4.2 m long. If cavitation takes place at the suction head of 4 m, the barometer stands at 10.3 m of water, and the water level in the sump is 3 m below the pump cylinder axis.3.1 Find the maximum allowable speed to operate the pump3.2 What power is expected in overcoming friction at this speed, take ƒ = 0.01
The plunger diameter of a single-acting reciprocating pump is 115 mm and the stroke is 230 mm. The suction pipe is 90 mm in diameter and 4.2 m long. If cavitation takes place at the suction head of 4 m, the barometer stands at 10.3 m of water, and the water level in the sump is 3 m below the pump cylinder axis.1. Find the maximum allowable speed to operate the pump
P1 = Patm 1 V 7.3 m/s %3D Flow h = 0.96 ft water 3 Density of water 1000 kg/m Determine the pressure at the point 3?
10.0 m 200 m 2. An old western town has a water tower to deliver water to the residents. Pictured above is the water tower. The water tower is closed but there is a section of air that is atmospheric pressure just above the water. The corsss ectional area at point 2 is 4.75 x 10 m. The cross sectional area fot the water tower is very large. What is the speed of the water coming out of the pipe at point 2? (density of water = kg/m³) 3. On a vacation trip up in Oregon my boys decided to build a 10 kg raft that they made out of driftwood. 1000
Q4:- Given - = 2 (2 - ) where u is the velocity of water in meter per second and y the distance from the boundary as shown below.(U=30 m/s, B=5 mm „u=1.005*10* N.s/m²).U, is the velocity of the plate. Calculate 1-The shear stress when y=2mm, 2-Velocity 3-The velocity in order to obtain t=0. Moving Ut=30 m/s Dr.Mun B Fixed