The figure shown is a built-up cross section composed of C-shaped and W-shaped steel beams attached by bolts of % in. diameter. It is a 20 ft simply supported beam subjected to a uniform loading of 411 b/ft throughout its span and a concentrated load, P (in Ib), at the midspan. a) Compute for the moment of Inertia of the cross section b) Determine the maximum bending stress in the beam. c) Calculate the spacing of bolts if its allowable shearing stress is 5000 psi. GIVEN: P = 65.0 kips E = 29000 ksi -C8X11.5 W8x28 C8X11.5 A d br t x(bar) ry AISC_Manual_Label Ibs/ft in in in in in in in in in in C8X11.5 11.5 3.37 8.00 2.26 0.220 0.390 0.572 32.5 3.11 1.31 0.623 W A d ry AISC_Manual_Label Ibs/ft in in in in in in in in in W8X28 28.0 8.25 8.06 6.54 0.285 0.465 98.0 3.45 21.7 1.62 Ik Y X- tw- eo bf k Хр bf PNA

The figure shown is a built-up cross section composed of C-shaped and W-shaped steel beams attached by bolts of % in. diameter. It is a 20 ft simply supported beam subjected to a uniform loading of 411 b/ft throughout its span and a concentrated load, P (in Ib), at the midspan. a) Compute for the moment of Inertia of the cross section b) Determine the maximum bending stress in the beam. c) Calculate the spacing of bolts if its allowable shearing stress is 5000 psi. GIVEN: P = 65.0 kips E = 29000 ksi -C8X11.5 W8x28 C8X11.5 A d br t x(bar) ry AISC_Manual_Label Ibs/ft in in in in in in in in in in C8X11.5 11.5 3.37 8.00 2.26 0.220 0.390 0.572 32.5 3.11 1.31 0.623 W A d ry AISC_Manual_Label Ibs/ft in in in in in in in in in W8X28 28.0 8.25 8.06 6.54 0.285 0.465 98.0 3.45 21.7 1.62 Ik Y X- tw- eo bf k Хр bf PNA

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A beam AB with a total length of 3m is supported by vertical rods at the ends, and it supports a downward load at Cof P-60KN, as shown in the figure. The diameters of the steel hanger rods are d130 mm and d2-25 mm. Neglect the weight of the beam AB and the rods. At what distancex from A must the load be placed such that o 0 And what is the corresponding axial stress in the rods? 3 m 3m (1) P=60 kN 2 m "Rigid
The Figure below shows a two-member truss supporting a block of weight W. The cross-sectional areas of the members are 800 mm² for AB and 400 mm² for AC. Determine the maximum safe value of W (kN) if the working stresses are 110 MPa for AB and 120 MPa for AC. ... B 40 deg. A 60 deg. A) 38.90 в) 55.30 61.70 76.2
A single span member is 3m in length is made up of Apitong 200mm x 300mm wooden section, with an allowable stress based on 80% stress grade. The beam carries a uniform load of 18 kN/m including its own weight. The beam carries an axial tensile load of 180 kN a.) Give the actual tensile stress if only tensile force is acting. b.) Give the interaction value of both bending and tensile stress. Determine whether the wooden section is safe or not. not redesign the wooden section. c.) Give the ratio of the difference between its actual bending and tensile stress to the adjusted bending stress for slenderness
The cross section of a steel beam is constructedof a W 18 × 71 wide-flange section with a 6 in. × 1/2 in.cover plate welded to the top flange and a C 10 × 30channel section welded to the bottom flange. This beamis subjected to a bending moment M having its vector atan angle θ to the z axis (see figure).Determine the orientation of the neutral axis andcalculate the maximum tensile stress σt and maximumcompressive stress σc in the beam. Assume thatθ = 30° and M = 75 kip-in. Note: The cross- sectionalproperties of this beam were computed in ExamplesD-2 and D-5.
A bridge girder AB on a simple span of length L = 20 m supports a distributed load of maximum intensity q at midspan and minimum intensity q/2 at supports A and B that includes the weight of the girder (see figure). The girder is constructed of three plates welded to form the cross section shown. (a) Determine the maximum permissible load q based upon an allowable bending stress sigma = 140 MPa. Round to the nearest tenth. qmax = ___ kN/m (b) Determine the maximum permissible load q based upon an allowable shear stress Tau = 60 MPa. Round to the nearest tenth. qmax = ___ kN/m
Two steel plates are welded together to form an inverted T-beam and are loaded as shown below. Determine the maximum bending stress developed. Also, determine the maximum shear stress at the neutral axis of the cross section. The following Inte Av = 9K Bv = 11K location of centroid = 3.56" above X-Ref Shear diagram Moment diagram 1" x 10" steel plate 1" x 8" steel plate X-reference A 6' 8K 12' 24' 12K 6' B of your work is accurate. Yo ment Mmax = 66K' Vmax 11K Moment of Inertia = 218 inª
Determine the maximum tensile and compressive bending stresses developed in the beam shown. The cross-section has the given properties. NA 1-35 x 10mm a. RA = b. RE= c. fb(c) = d. fb(T) = 80 mm 200 mm A 1.5m kN KN 5kN m MPa MPa B 1.5m SkN/m 2m 5KN n 2m 4
11. Link BC is 6 mm thick and is made of a steel with a 450-MPa ultimate strength in tension. What should be its width w if the structure shown being designed to support a 20-kN load P with a factor of safety of 3? 600 mm- A B 90 480 mm
From the given figure below, determine the maximum flexural stress of the beam if it has a cross section of 150mm wide by 250mm deep. (JN 10 N/m o' RA=42N 42N 3M B IM 75Nm 81NM Im RD=3N -3N 0° 78 Nm 3NM V-DIAG M-DIAG
a.what is the maximum bending stress fbx (MPa) in the girder b.determine the maximum bending stress fby (MPa) in the girder c.using interaction formula fbx/Fbx + fby/Fby
The T-beam in the floor system has a slab thickness of 90 mm and supported by beams 6.5 m span. The beam is casts monolithically with the slab. The spacing of beams is 2 m on centers and width the web is 400 mm. The effective depth of the beam is 600 mm. It is reinforced at tension side with 8-28mm Φ bars. fc’ = 28 MPa, fy = 415 MPa 1. Which of the following most nearly give the effective width of the flange? a. 1565 mm b. 1305 mm c. 1275 mm d. 1625 mm 2. Which of the following most nearly gives the depth of compression block? a. 62.25 mm b. 52.86 mm c. 60.26 mm d. 58.29 mm 3. Which of the following gives the nominal moment capacity of the beam? a. 1461.25 kN/m b. 1156.36 kN/m c. 1163.15 kN/m d. 1172.58 kN/m
O FS = 2.4 O FS = 2.2 Consider a simple supported beam subjected to the load shown. The beam has a solid square cross-section with edge "a", and made of steel alloy having a yielding tensile and compressive strength of oy = 400 MPa. Determine its minimum required edge "a" for a factor of safety against yielding FS = 2.5. The area moment of inertia of that section about its neutral axis N.A. is INA = b.h³/12. of 3 kN 2 kN/m D 6 m + Select one: 5:37 PM 86°F Light rain ENG 6/18/2021 hp