2. The beam with cross-section shown carries a uniformly distributed load of intensity w over its entire length. Determine w if the allowable stresses are g = 40 MPa, g = 80 MPa, and T = 12 MPa. w (kN/m) 75 mm 10 mm 10 mm- 150 mm ost 0.5 m 1 m 3 m :10 mm 150 mm

2. The beam with cross-section shown carries a uniformly distributed load of intensity w over its entire length. Determine w if the allowable stresses are g = 40 MPa, g = 80 MPa, and T = 12 MPa. w (kN/m) 75 mm 10 mm 10 mm- 150 mm ost 0.5 m 1 m 3 m :10 mm 150 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Problem #2. The steel rod is stress-free before the axial loads P₁ = 150 kN and P₂ = 90 kN are…

Q: 4. (a) A cantilever AB of length Im carries a uniformly distributed load, w N/m from the fixed end A…

A: Above given data we have to find total permissible load w

Q: The beam shown is hinged at one end. It is supported by two steel rods of equal length of 1.5m.…

Q: f the bending stress at section 2-20 MPa. What are the bending stresses at sections 1, 3, and 12 mm…

Q: SOLVE BOTH AND GET A LIKE <3

A: This question is related to the Structure Analysis. In Both question Option A is correct answer ,…

Q: The beam shown below has a cross section of channel shape with width b=400 mm and height h=80 mm,…

Q: 2 A leaf spring is made of plates 50 mm wide and 8 mm thick. The spring has a span of 700 mm.…

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of…

Q: mm rectangles arranged as shown. A. Determine the maximum value of w without exceeding the…

A: solution of above problem is below:

Q: The beam with cross-section shown carries a uniformly distributed load of intensity w over its…

A: Given, There is a two side overhang beam given in the question. Total length of the beam = 4.5m…

Q: A W410 x 60 standard steel shape is used to support the loads shown on the beam in the figure.…

A: P= 132kN,w= 24kN/ma= 3mb= 2mFree body diagram of beam:-

Q: A rectangular beam has a dimension of 210 mm x 260 mm. The simply supported beam is 5-m long and…

A: To Determine Maximum flexural stress of the beam.

Q: 16 kN 60 12 70 Ölçüler mm cinsindendir.

A: Finding out stress at point A.

Q: if the maximum shear stress acting on rectangular beam is 50 N/mm, determine the average shear…

Q: 5 kN 5 kN - 5 kN/m B I m 1m 1 m

A: Given, b = 100 m h = 250 mm

Q: Question 2) In the system given in the figure, a distributed load of w=85 kN/m acts on the rod AB of…

Q: The force P is applied at d = 50 mm from the bottom as shown. Compute the normal stress at section…

A: Given: The value of d is 50 mm. The value of P is 85 kN. Consider the figure,

Q: Upvote will be given. Please write the solutions legibly. Solve in 2 decimal place 15 KN 20 KN/m 4m…

Q: Upvote will be given. Please write the solutions legibly. Solve in 2 decimal places. A 10 KN 10 KN…

A: A simply supported beam is loaded as followsmax shear stress=?max flexural stress=?crossection :…

Q: 50 lb-ft T2 (1) 30 lb-ft A (3) B C D Assume for the above sketch that the shaft is restrained from…

Q: The beam shown below with a length L = 16 m and a rectangular cross section that has a width of b =…

A: Find reactions:∑ MR=0R1L-PL-x=0R1=13P16

Q: A beam with the cross-section shown is subjected to a vertical shear of 28 kN. Determine: (a) the…

Q: For the simply supported beam with the given cross-section, the shear force diagram has been…

Q: The beam with cross-section shown carries a uniformly distributed load of intensity w over its…

A: Here we find 1. Support reaction by the help of three equilibrium equation. 2. Draw shear force…

Q: In the figure, find the length c of the overhangs so that the beam made of U profile can carry the…

Q: The beam shown below has a cross section of channel shape with width b3200 mm and height h=80 mm,…

Q: Problem 3 A block with a weight W hangs from a pin at A. Support bars AB and AC are pinned to the…

Q: Two plates each 25 mm thick and 130 mm wide are fastened by three 20 mm diameter rivets. Assume that…

A: The tensile stress is defined as the ratio of the applied load in the direction of increasing length…

Q: A wooden beam whose length is 1 m is 100 mm wide and 200 mm high. It carries a load of 100 kN as…

A: Given data :- A wooden beam length = l = 1m width = b = 100 mm = 0.1 m height = h = 200 mm = 0.2 m…

Q: 4. A force Q is applied to a rectangular member with a size of 3oomm x 450mm. Q is located 37.5mm…

A: Applying Bending stress and Direct stress concept Q load is applied with ecentricity on both axis…

Q: Question 3. The steel shaft has a diameter of 40 mm and is fixed at its ends A and B. If it is…

A: Given data: LAC=400 mm LCB=600 mm diameter= 40 mm G=75 GPa.

Q: The principal stresses are incorrect but the maximum shear stress is correct. What are the two…

A: Compressive stress is the force that deforms the material in a way that reduces the volume of the…

Q: In the figure, find the length c of the overhangs so that the beam made of U profile can carry the…

Q: In урат N 5cm shear and horma Find stress Find moment of inertia, Find the normal stress / Volume…

Concept explainers

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.

Question

2. The beam with cross-section shown carries a uniformly distributed load of intensity w over
its entire length. Determine w if the allowable stresses are g = 40 MPa, gs = 80 MPa, and T =
12 MPa.
w (kN/m)
75 mm
10 mm
10 mm-
150 mm
0.5 m
1 m
3 m
:10 mm
150 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A beam shown below has a T-shaped cross section. Determine the maximum compressive stress of the beam. T I = 87-49 in 4 400 16/+ ↓ ↓ ↓ ↓ ↓ ↓ ↓ B TOFT 16001b 160016 4.17 1° 3200 lbft 2.914 in - 3400/6 5.886 in -NA 4FT 10° 100016 -240016 -4000 16 ff 1000lb dc V M
Final answer must be 2 decimal places. Don't round off initial values ty
A rigid beam is being supported by three suspender bars made of bronze and loaded as shown in the figure. The cross-sectional area of each bar is 442 mm². Determine the axial stress in each bar. B 2 m O 1 m 5Q KN 1 m O E 1 m 8T KN 1 m LL
A cantilever beam AB is loaded as shown in the Cross-section of the beam figure and the beam is supported with a cable BD. The beam's cross-section is rectangular as shown. It is known that the tension force in cable BD is 10.39 kN. Calculate the normal stress at point a, and calculate the shear stress at point c. Ignore the weight of the beam. 10cm 10cm +15cm+ 75cm B F-13.99KN 30cm 60cm 90cm
2. The beam with cross-section shown carries a uniformly distributed load of intensity w over its entire length. Determine w if the allowable stresses are g = 40 MPa, g = 80 MPa, and t = | T 12 MPa. w (kN/m) 75 mm 10 mm 0.5 m : 10 mm 3m 10 mm- 150 mm 150 mm
working stress method
A square bar carries a series of loads as shown in Figure P1-47. Compute the stress in each segment of the bar. All loads act along the central axis of 1-47. the bar.
1000 N/m Given: A cantilever beam has loading and cross section as shown. The allowable stress is 64 MPa. 150 mm Determine: the minimum width for the beam 6 m b
2. The bending moment acting on the triangular cross section of a beam is M = 3.6 kN m. Determine the maximum tensile and compressive bending stresses acting on the cross section. M 120 mm 60 mm-