The figure below is a schematic drawing of a shaft that supports two V-belt pulleys. The loose belt tension on the pulley at A is 15% of the tension on the tight side. The shaft material has a yield strength of 300 MPa and an ultimate tensile strength of 520 MPa. Calculate the shaft diameter. The loose belt tension on the pulley at A is 15% of the tension on the tight side. Theshaft material has a yield strength of 300 MPa and an ultimate tensile strength ofThe figure below is a schematic drawing of a shaft that supports two V-belt pulleys.520 MPa. Calculate the shaft diameter.30045°P2`400P0,0150- 300 D.250 D.E50 N270 N

Given, The yield strength of the material, sy=300 MPa The ultimate strength of the material, su=520…

The figure below is a schematic drawing of a shaft that supports two V-belt pulleys. The loose belt tension on the pulley at A is 15% of the tension on the tight side. The shaft material has a yield strength of 300 MPa and an ultimate tensile strength of 520 MPa. Calculate the shaft diameter. 300 45° P2 400 P, 150 B C 300 D. 250 D. 50 N E 276 N

The figure below is a schematic drawing of a shaft that supports two V-belt pulleys. The loose belt tension on the pulley at A is 15% of the tension on the tight side. The shaft material has a yield strength of 300 MPa and an ultimate tensile strength of 520 MPa. Calculate the shaft diameter. 300 45° P2 400 P, 150 B C 300 D. 250 D. 50 N E 276 N

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.8.10P: A steel punch consists of two shafts: upper shaft and lower shaft. Assume that the upper shaft has a...

See similar textbooks

Related questions

Q: The bar shown in the following figure has a diameter of 40 mm and is subjected to a force P = 4500 N…

A: The Point A will be subjected to tensile stress due to bending stress generated by force F.bending…

Q: A solid, circular bar ABC consists of two segments, as shown in the figure. One segment has a…

A: When a shaft is subjected to torque, shear stress produces in the shaft. The torsion equation is…

Q: Figure Q1 shows a shaft AB (modulus of rigidity G = 73 GPa) with a total length of 1270 mm that is…

A: This is a problem of indeterminate beam, so we can calculate the reactions at A and B. These…

Q: A steel shaft in the form of a solid body circular rod or a circular tube can be manufactured.…

Q: (b) Figure Q6(b) shows a cantilever shaft made of steel subjected to several loading T = 5kNm, M =…

Q: Useful equations; o = E A 1. The steel shaft carries the axial loads as shown in the figure below.…

A: Given axial load action on stepped shaft as shown below

Q: An input shaft of a gearbox with motor power P = 7 kW and rotation number n = 1300 rpm. The diameter…

Q: Three parallel vertical rods of equal length (L-2m) support a rigid beam AB to which a force…

A: Given dataLength of the rods L = 2mTransvers load acting on the rigid beam P = 40kNProperties of…

Q: A composite shaft consists of a brass sleeve securely bonded to half steel shaft, fixed at end A as…

A: Given data:

Q: Given the figure shown below, bronze and aluminum compound shaft are attached to rigid supports. The…

A: To find: The maximum torque carried by the aluminum shaft. Given: The diameter of bronze shaft is…

Q: B2 A tube of 50 mm outside diameter and 2 mm thickness is attached at the ends by means of rigid…

Q: A keyed sprocket delivers a torque of 778.8 N - m thru the shaft of 54 mm OD. The key thickness is…

Q: 4. A central horizontal section of a hook is symmetrical trapezium 90 mm deep. The inner width being…

A: Note:As per our guidelines we are supposed to answer only one question. Kindly repost other…

Q: A hollow cylinder is used as a torque sensing element with r= 2.5 cm, ro=3.3 cm and L=15 cm.…

A: Given:- T=30 N-mG=8×1010N/m2ri=2.5cm=0.025mr0=3.3cm=0.033mL=15cm=0.15mθ=45° To find:- Size of solid…

Q: A shaft made of steel receives 7.5 kW power at 1500 1.p.m. A pulley mounted on the shaft as shown in…

Q: A 1m long steel bar (E=200GPa) of 10mmx10mm dimension fixed at both ends is heated to 90°C from…

Q: A solid steel shaft of radius b is to be pressed into a wrought iron hub of outer radius c and…

A: A solid steel shaft of radius b is to be pressed into a wrought iron hub of outer radius c and…

Q: Fi=5 kN 100mm F1OKN 1s0mm 3R. 1,5 R $40mm 20 mm p ø Somm 25 mm Sa 150 mm IS0 mm 25mm

Q: A shaft whose torque varies from 2200 to 6400 in-lb. It has a diameter of 1.25 inches and yield…

Q: hena) A hot-rolled steel shaft with a shoulder fillet is subjected to an axial load P which varies…

A: When a load or force is acting on an object in a way that it is parallel and on its axis then it is…

Q: Problem 5: (D2) You are an engineering intern at a manufacturer of mechanical tools, your senior…

Q: Rigid bar ABC is supported by two identical solid bronze [oy = 331 MPa; E = 105 GPa; a = 22.0 x…

Q: 1. Two short shafts having identical diameters of 35 mm and rotating at 1000 rpm are connected by a…

Q: When a bar with the hexagonal cross section shown in Fig. (a) is subjected to a torque T, numerical…

Q: A spherical tank contains an internal pressure of 3.0 MPa, the diameter is 16 m, the yield stress…

Q: P1.8 (WP Determine the normal stress in rod (1) for the mechanism shown in Figure P1.8. The diameter…

Q: A composite shaft consists of a brass sleeve securely bonded to half steel shaft, fixed at end A as…

Q: No results for "2. A 50 mm diameter shaft was made of steel with a yield strength ad ultimate…

A: Given data as per the question diameer of shaft =50 mmyield strength of shaft=220 Mpaultimate…

Q: Q4/A 40 kw power at 300 rpm is transmitted from 50 mm diameter shaft by means of two identical…

A: Given data: Power transmitted by the shaft (P) = 40 kW Speed of the shaft (N) = 300 rpm Diameter of…

Q: Rigid bar ABC is supported by two identical solid bronze [oy=331 MPa; E = 105 GPa; a = 22.0 x…

Q: 0.6 m 1 m 1200 N.m d,= 30 mm- B A 800 N.m d, = 60 mm Figure 4 c) Consider a shaft in Figure 4 is a…

Q: A rod as shown in Figure Q1 is fixed to a rigid wall at its end point A and is made of a steel tube,…

A: Answer: (i) The minimum diameter of rod d is 43.245 mm. (ii) The angle of twist of point B relative…

Q: 1. A taper pin is used to fix a lever to a shaft, if it is to transmit a maximum torque of 850…

A: Given: The torque transmitted by shaft, T = 850 lb.in The shaft diameter, d = 1.75 in The ultimate…

Q: B. 5 m 3 m 30 mm -20 mm T20 mm The assembly above includes pin-connected column AB. Suppose that an…

Q: A composite shaft consists of a brass sleeve securely bonded to half steel shaft, fixed at end A as…

Q: 1 Point A mild steel tie bar is to withstand a maximum tensile force of 100 kN. The ultimate tensile…

A: We have to determine diameter of bar

Q: 40 Steel d = 30 mm A G= 83 GPa 1.2 m

A: Calculated resisting torque at support at A and B .

Q: A 2-inch line shaft is transmitting 20 hp rotating at 200 rpm, carrying two pulleys spaced 30 inches…

Q: A composite shaft consists of a brass sleeve securely bonded to half steel shaft, fixed at end A as…

Q: The cantilevered bar in the figure is made from a ductile material and is statically loaded with Fy…

Q: The figure below shows a stepped shaft having D = 35 mm, d = 25 mm, and r= 3 mm. The shaft is made…

A: Given Data: The ultimate tensile strength of the shaft is, σut=450 MPa. The corrected fatigue…

Q: The bar shown in the following figure has a diameter of 40 mm and is subjected to a force P = 1500 N…

A: Given:F=500 NP=1500 Nd=40 mmSyt=60MPaI=π64*404 =125663.70 mmStresses acting at point A:The Force…

Q: A steel pipe is part of a drilling rig to build foundation piles The outer d 2 is equal to 6 in and…

A: To obtain the magnitude of the shear force on the various fibers of the beam, we must use the pure…

Q: 5 m 3 m 30 mm 20 mm 20 mm The assembly above includes pin-connected column AB. Suppose that an…

Q: Question 4 The bar in Figure is made of steel that is assumed to be elastic perfectly plastic, with…

Q: Aluminum A = 400 mm Bronze A = 200 mm Problem 2: An aluminum rod is rigidly attached between a steel…

A: Given dataMaximum stress in steel σmaxs = 140MPaMaximum stress in aluminium σmaxa = 90MPaMaximum…

Q: A steel rod of diameter D = 50 mm has a tensile yield strength of 345 MPa supports an axial load P =…

Q: PROBLEM 4. An airplane wing made of 2014-T6 aluminum alloy is modeled as a closed cross-section thin…

A: Given data: The uniformly distributed torque is t = 500 kN-m/m. The length of the wing is L = 8000…

Q: Figure Q6(b) shows a cantilever shaft made of steel subjected to several loading T = 5kNm, M =…

Concept explainers

Torsion

In mechanical engineering, torque, torsion, and twisting moment are three of the most important concepts which have different meanings. Torque is the consequence of a moment of a force that produces an angular acceleration in a body or induces rotational kinetic energy in a body. For instance, in an automobile, the power transmission shaft is a body that is always under rotation due to the external torque acting on it, this torque is created by the engine.

Question

The loose belt tension on the pulley at A is 15% of the tension on the tight side. The
shaft material has a yield strength of 300 MPa and an ultimate tensile strength of
The figure below is a schematic drawing of a shaft that supports two V-belt pulleys.
520 MPa. Calculate the shaft diameter.
300
45°
P2
`400
P
0,0
150
- 300 D.
250 D.
E
50 N
270 N

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Trending now

This is a popular solution!

Step by step

Solved in 7 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
A crank arm consists of a solid segment of length bxand diameter rf, a segment of length bltand a segment of length byas shown in the figure. Two loads P act as shown: one parallel to — vand another parallel to —y. Each load P equals 1.2 kN. The crankshaft dimensions are A] = 75 mm, fr> = 125 mm, and b3= 35 mm. The diameter of the upper shaft isd = 22 mm, (a) Determine the maximum tensile, compressive, and shear stresses at point A, which is located on the surface of the shaft at the z axis. (b) Determine the maximum tensile, compressive, and shear stresses at point B, which is located on the surface of the shaft at the y axis
A steel punch consists of two shafts: upper shaft and lower shaft. Assume that the upper shaft has a diameter d1= 24 mm and the bottom shaft has a diameter d2= 16 mm. The punch is used to insert a hole in a 4 mm plate, as shown in the figure. If a force P - 70 kN is required to create the hole, what is the average shear stress in the plate and the average compressive stress in the upper and lower shaft of the punch?
The piston in an engine is attached to a connecting rod AB, which in turn is connected to a crank arm BC (see figure). The piston slides without friction in a cylinder and is subjected to a force P (assumed to be constant) while moving to the right in the Figure. The connecting rod. with diameter d and length L, is attached at both ends by pins. The crank arm rotates about the axle at C with the pin at B moving in a circle of radius R. The axle at C, which is supported by bearings, exerts a resisting moment M against the crank arm. (a) Obtain a formula for the maximum permissible force Pallow. based upon an allowable compressive stress acin the connecting rod. (b) Calculate the Force Pallowfor the following data:
Two sections of steel drill pipe, joined by bolted flange plates at Ä are being tested to assess the adequacy of both the pipes. In the test, the pipe structure is fixed at A, a concentrated torque of 500 kN - m is applied at x = 0.5 m, and uniformly distributed torque intensity t1= 250 kN m/m is applied on pipe BC. Both pipes have the same inner diameter = 200 mm. Pipe AB has thickness tAB=15 mm, while pipe BC has thickness TBC= 12 mm. Find the maximum shear stress and maximum twist of the pipe and their locations along the pipe. Assume G = 75 GPa.
Two steel wines support a moveable overhead camera weighing W = 28 lb (see figure part a) used For close-up to viewing of field action at sporting, events. At some instant, wire I is at an angle a = 22° to the horizontal and wire 2 is at angle fi = 40°. Wires I and 2 have diameters of 30and 35 mils, respectively. (Wire diameters are often expressed in mils; one mil equals 0.001 in.) (a) Determine the tensile stresses s and s2 in the two wires. (b) If the stresses in wires 1 and 2 must be the same, what is the required diameter of wire 1 ? (c) To stabilize the camera for windy outdoor conditions, a third wire is added (see figure part b). Assume the three wires meet at a common point coordinates (0, 0. 0) above the camera at the instant shown in figure part b. Wire I is attached to a support at coordinates (75 ft, 48 ft, 70 Ft). Wire 2 is supported at (-70 ft. 55 ft, 80 Ft). Wire 3 is supported at (-10 ft. -85 Ft, 75 ft). Assume that all three wires have a diameter of 30 mils. Find the tensile stresses in all three wires
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield stress is 590 MPa, and the factor of safety is 3.0. (a) Determine the required thickness to the nearest millimeter. (b) If the tank wall thickness is 85 mm, what is the maximum permissible internal pressure?
A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
Repeat Problem 11.2-14 using L = 12 ft, ß = 0.25 kips/in., ßRl= 1.5ßL2, and ßR2= 2 ßR1.
Compare the angle of twist 1 for a thin-walled circular tube (see figure) calculated from the approximate theory for thin-walled bars with the angle of twist 2 calculated from the exact theory of torsion for circular bars, Express the ratio 12terms of the non-dimensional ratio ß = r/t. Calculate the ratio of angles of twist for ß = 5, 10, and 20. What conclusion about the accuracy of the approximate theory do you draw from these results?
The strength-to-weight ratio of a structural material is defined as its load-carrying capacity divided by its weight. For materials in tension, use a characteristic tensile stress obtained from a stress-strain curve as a measure of strength. For instance, either the yield stress or the ultimate stress could be used, depending upon the particular application. Thus, the strength-to-weight ratio RS/Wfor a material in tension is defined as Rs/w= in which a is the characteristic stress and 7 is the weight density. Note that the ratio has units of length. Using the ultimate stress Uas the strength parameter, calculate the strength-to-weight ratio (in units of meters) for each of the following materials: aluminum alloy 606I-T6, Douglas fir (in bending}, nylon. structural steel ASTM-A57.2, and a titanium alloy. Obtain the material properties from Tables [-1 and 1-3 of Appendix I. When a range of values is given in a table, use the average value.