The extruded plastic shape will be subjected to an internal shear force of V = 245 Ib. Dimensions of the cross section are b= 1.4 in., d = 2.8 in., c = 1.9 in., and t = 0.12 in. Determine: (a) the magnitude of the horizontal shear stress at points A and B. (b) the magnitude of the horizontal shear stress at point C, which is located at a distance of yc = 1 in. below the z centroidal axis. (c) the magnitude of the maximum horizontal shear stress in the extrusion. (tур.) A B d Ус V C

The extruded plastic shape will be subjected to an internal shear force of V = 245 Ib. Dimensions of the cross section are b= 1.4 in., d = 2.8 in., c = 1.9 in., and t = 0.12 in. Determine: (a) the magnitude of the horizontal shear stress at points A and B. (b) the magnitude of the horizontal shear stress at point C, which is located at a distance of yc = 1 in. below the z centroidal axis. (c) the magnitude of the maximum horizontal shear stress in the extrusion. (tур.) A B d Ус V C

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the absolute maximum shear stress for each of the following plane stress states for which the principal stresses are given. (a) op1 = 2700 psi, op2 = -2470 psi, Op3 = 0 (b) op1 = 44 MPa, op2 = 25 MPa, op3 = 0
Due to loading, the plate is deformed into the dashed shape shown in the figure. Assume a = 39 in., b= 33 in., δ1= 0.1625 in., δ2= 0.1 in. Determine the average normal strain along the side AB?in micro rad And answer in right and clear way Determine the average shear strain in the plate at A relative to the horizontal and vertical axes?
Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sy-17 MPa, S, - 60 MPa, and Swy- 29 MPa. (a) Draw Mohr's circle for this state of stress. (b) Determine the principal stresses (ơp > op2) and the maximum in-plane shear stress Tmax acting at the point. (c) Find the smallest rotation angle 0, (counterclockwise is positive, clockwise is negative) that will rotate to principal directions. Then show these stresses in an appropriate sketch (e.g, see Figure 12.15 or Figure 12.16) Say Answers: MPa. Opl = MPa. MPa. Tmax = 0, =
Determine the absolute maximum shear stress for each of the following plane stress states for which the principal stresses are given. (a) Op1 = 2780 psi, Op2 = -2440 psi, op3 = 0 (b) op1 = 58 MPa, op2 = 35 MPa, Op3 = 0 Answer: (a) Tabs max= psi (b) Tabs max = MPa
The extruded plastic shape will be subjected to an internal shear force of V= 315 lb. Dimensions of the cross section are b = 1.3in, d= 2.6 in, c= 18 in, and t= 0.11 in. Determine: (a) the magnitude of the horizontal shear stress at points A and B. (b) the magnitude of the horizontal shear stress at point C, which is located at a distance of yc = 0.9 in. below the z centroidal axis. (c) the magnitude of the maximum horizontal shear stress in the extrusion. (tуp.) B' d Ус Answer: (a) TA = psi Tg = psi (b) Tc =1 psi (c) Tmax psi
Determine the absolute maximum shear stress for each of the following plane stress states for which the principal stresses are given. (a) Op1 = 3300 psi, Op2 = -1830 psi, Op3 = 0 (b) 0p1 = 44 MPa, Op2 = 29 MPa, Op3 = 0 Answer: (a) Tabs max psi (b) Tabs max= MPa
Your answer is partially correct. Determine the absolute maximum shear stress for each of the following plane stress states for which the principal stresses are given. (a) op1 = 2780 psi, o,2 = -2440 psi, op3 = 0 (b) Op1 = 58 MPa, Op2 = 35 MPa, Op3 = 0 Answer: (a) Tabs max psi 1390 (b) Tabs max MPa 29