The electric motor exerts a 500-N-m torque on the aluminum shaft ABCD when it is rotating at a constant speed. The torques exerted on pulleys B and C are as shown. Take a = 1.4 m, b= 0.6 m, and G= 27 GPa. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 200 N.10 40 mm 300 N-m 44 mm 45 man nine the angle of twist between B and D. gle of twist between B and Dis 16.2

The electric motor exerts a 500-N-m torque on the aluminum shaft ABCD when it is rotating at a constant speed. The torques exerted on pulleys B and C are as shown. Take a = 1.4 m, b= 0.6 m, and G= 27 GPa. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 200 N.10 40 mm 300 N-m 44 mm 45 man nine the angle of twist between B and D. gle of twist between B and Dis 16.2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Required information The electric motor exerts a 500-N-m torque on the aluminum shaft ABCD when it is rotating at a constant speed. The torques exerted on pulleys Band Care as shown. Take a= 1.5 m, b= 0.9 m, and G= 27 GPa. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 300 N n 200 N. m 44 mm a 40 mm I m Determine the angle of twist between B and D. The angle of twist between B and D is
The aluminum rod BC (G= 26 GPa) is bonded to the brass rod AB (G= 39 GPa). Each rod is solid and has a diameter of 12 mm. Take T= 124 N-m. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 200 mm Brass B Aluminum 300 mm T Determine the angle of twist at B. The angle of twist at B is[
Find the relationship between 8₁, the elongation of rod (1), and the internal tensile force, F₁, in rod (1). Assume 8, is a positive value in units of mm and F₁ is a positive value in units of kN. So, the answer you enter for the ratio (8₁/F₁) must be in units of ( mm/kN). 8₁ F₁ = i ! mm/kN
The motor delivers a torque of T = 60 N-m to the shaft AB. This torque is transmitted to shaft CD using the gears at E and F. The bearings B, C, and D allow free rotation of the shafts. Figure ▼ 50 mm 35 mm Part A 30 mm B T = Submit Part B Determine the equilibrium torque T on shaft CD (Eigure 1) Express your answer with the appropriate units. D μA Value ▼ Part C 1 Request Answer HÅ (TAB)max = Value Submit Request Answer Determine the maximum shear stress in AB shaft. Express your answer with the appropriate units. μÃ C 125 mm (TCD)max = Value Submit Request Answer Units Determine the maximum shear stress in CD shaft. Express your answer with the appropriate units. 3 PHIE Units 0 Units B < 1 of 1 ? DAME ? ?
Three springs A, B, and C has spring constants 213 N/mm, 143 N/mm, 341 N/mm respectively. Determine the equivalent spring constant if the springs are in SERIES
F1=603N F2 =818N show a detailed solution please
Turning moment 1mm = 60NM: crank angle, 1 mm = 1°. The turning moment shows the maximum energy that needs to be stored by the flywheel in unit area is 2850 m?. The flywheel rotates at an average speed of 220 rpm with a total speed change of 2.5%. If the mass of the flywheel is 500 kg, find the appropriate dimensions (inner diameter, outer diameter and thickness) of the flywheel. Given that inner diameter of the flywheel is 0.9 outer diameter and the density is 7.2 Mg/m3. Reply.
The aluminum alloy [G = 4000 ksi] pipe is fixed to the wall support at C. The bolt holes in the flange at A were supposed to align with mating holes in the wall support; however, an angular misaligment of 4° was found to exist. To connect the pipe to its supports, a temporary installation torque T'B must be applied to B to align flange A with the mating holes in the wall support. The outside diameter of the pipe is 5.5625 in. and its wall thickness is 0.258 in. The segment lengths are L1= 16 ft and L2 = 24 ft. a) Determine the temportary installation torque T'B that must be applied to B to align the bolt holes at A b) Determine the maximum shear stress τinitial in the pipe after the bolts are connected and the temporary installation torque at B removed c)Determine the magnitude of the maximum shear stress in segment (1) and (2) if an external torque TB= 150 kip-in. is applied at B after the bolts are connected
Questio The non-linear spring shown in the image below has a stiffness, K, given by the equation: K = 7 - 5u where u is the extension of the spring. Using the incremental method with 4 increments, calculate the extension of the spring if the end force, F, is 1. Give your answer to 4 decimal places. Fun F K 21 Your Answer: Answer
In the design in the figure, a force of Fn=45992 N acts in the vertical plane on a machine element with a diameter of D=200 mm on the shaft resting on the A and B bearings. If the angle made by this force with the horizontal is b=40o, find the life of the 6210 coded Deep Ball bearing to be used in the B bearing, in hours. Number of revolutions = 30 rpm. 1-) The diameter of the machine element on which the force acts will be taken into account in the calculation of bearing forces (That is, it will be assumed that the Fn force AFFECTS THE GROUND shown in the figure, NOT the axis of the shaft). 2-) Pi number will be taken as 3.14.
My answer here is R_av= 150 kN, R_b= 210 kN amd R_ah= 0 kN please verfy if my answers are correct
What is the power output of a motor that provides a torque of 2,917 N*m while running at 2,641 rpm? Provide your answer in kW and round to the nearest whole number.